Da-Lite PRO IMAGER Manuel utilisateur

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 13

Warsaw, Indiana 46581-013

Phone: 5 4-26 -8101

800-622-3 3

Fax: 5 4-26 - 804

www.da-lite.com

e-mail: [email protected]

POWER

PRESENTATION PRODUCTS

The

Instruction Book for

PRO IMAGER

IMPORTANT SAFETY INSTRUCTIONS

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled,

or contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rat-

ing at least equal to that of the appliance should be used.

Cords rated for less amperage than the appliance may over-

heat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric

shock when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by

the manufacturer may cause a risk of fire, electric shock, or

injury to persons.

SAVE THESE INSTRUCTIONS

FRAME ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

5/16" socket or wrench

Carpenters level

Tape Measure

1. Unpack frame pieces and lay them face down on

the floor. The top frame has the roller and motor

assembly attached to it. The side frames are the

two short pieces.

2. Attach the side frame pieces to the top frame.

See figure 1. Insert the slat bar into the small

channel located on the side frame. Fasten the

frame pieces with four #10 x 3/4" hex head

screws.

NOTE: the top and bottom frame pieces will over-

lap the side frame pieces.

3. HORIZONTAL MASK ONLY - Attach the bottom

frame with four #10 x 3/4" hex head screws.

Attach the bottom brackets with the two screws

at the back of the frame as shown in figure 2.

VERTICAL MASK ONLY - Attach the pull straps to

the bottom slat bar by sliding the looped end of

the pull straps over the ends of the slat bar (See

figure 2 for pull strap attachment). The bottom

roller is spring loaded and has an internal lock to

keep it from retracting during shipping. To disen-

gage the lock pull on the slat bar to unroll the

mask but DO NOT let go of the slat bar. To lock

the roller let the mask retract slowly and the lock

will engage. The lock will only engage when the

frame is laying face down on the floor. When the

frame assembly is hanging on the wall the lock

will not engage. Insert the slat bar into the small

channel on the side frame. Fasten the bottom

frame with four #10 x 3/4" hex head screws.

Attach the bottom brackets with the two screws

at the back of the frame as shown in figure 2.

SLAT BAR

FIG. 1

CHANNEL

1/ " MAX.

PULL STRAP

GUIDE

PULL STRAP

SLAT BAR

VIEWING

SURFACE

FIG. 2

#10 x 3/4" SCREWS

BOTTOM

BRACKET

#10 x 3/4" SCREW

1. To install the Pro Imager over a Da-Lite Perm-Wall screen you will need to place the supplied wooden spacers

between the screen and the wall.

Da-Snap and Imager screens do not require any spacers.

2. Refer to figure 3 for hanger bracket location. Dimension A will vary depending on the type of screen you have.

Dimension A is measured from the top of the screen frame to the top of the hanger bracket.

Screen type Dimension A

Perm-Wall 3-7/ "

Imager 3-7/ "

Da-Snap 4-3/ "

Securely fasten the hanger bracket to the wall. It is recommended that you

use #10 x 1-3/4" wood screws (not supplied) and fasten into the wall stud.

Use a level to make sure the bracket is level.

To provide easy access to the limit control switches (see adjustment proce-

dures) you will need at least 7" clearance above the top of the Pro Imager.

3. Hang the frame assembly on the hanger bracket as shown in figure 3.

4. Fasten the bottom bracket to the wall with the appropriate type fastener for

your wall.

INSTALLATION (Continued)

HANGER

BRACKET

SPACER

BLOCK

FIG. 3

SCREEN

PRO IMAGER INSTALLATION

DOWN

RED

BLACK

COMMON

WHITE

BLACK WITH

YELLOW

BLACK

WHITE

RED

DOWN

ROCKER

SWITCH

AC COMMON

AC HOT

OPERATING SWITCH,

SWITCH BOX, AND

PLATE FURNISHED

WITH SCREEN. (SPDT

WITH CENTER OFF)

120V. 60-HZ 2.5 MAX. AMP

TO MOTOR

IN MULTIPLE CONTROL

INSTALLATIONS THIS SWITCH

IS REPLACED BY THE LOW

VOLTAGE CONTROL, OPER-

ATED FROM PUSH BUTTON

STATIONS.

THIS SWITCH CANNOT BE USED WITH LVC.

Note: A single switch cannot be used to operate more than

one screen. Contact the factory for further information.

SIDE VIEW

OF SWITCH

AND BOX

120V WIRING DIAGRAM

OFF

2 0 VOLT WIRING DIAGRAM

FOR STANDARD WALL SWITCH:

Da-Lite offers two styles of 240 volt

wall switches for standard operation.

Please see wiring diagram included in

wall switch box included with screen.

ADJUSTMENT

Masking travel is stopped automatically in the up and down positions by limit switches that are properly adjusted at

the factory. Should it be necessary to adjust the stop positions, proceed in the following manner using a small flat

screwdriver or a 5/32" allen wrench. Access to the switches is provided by holes on the top left side of the Pro

Imager. Refer to figure 4.

UP LIMIT CONTROL

The up limit controls the stop position when the mask is traveling up,

or unmasking the screen. Set the Pro Imager to the down, or masked

position. Turn the up limit control CLOCKWISE to DECREASE the up

travel. Turn it COUNTER-CLOCKWISE to INCREASE the up travel. Turn

the control a quarter turn at a time and then run the Pro Imager to

check the stop position. Repeat the above steps until the desired po-

sition is reached.

NOTE: The bottom of the slat bar should be no more than 1/ " above

the edge of the frame while in the up position. See figure 2.

DOWN LIMIT CONTROL

The down limit controls the stop position when the mask is traveling

down, or masking the screen. Set the Pro Imager in the up position.

Turn the down limit control CLOCKWISE to DECREASE the down travel.

Turn it COUNTER-CLOCKWISE to INCREASE the down travel. Turn the

control a quarter turn at a time and then run the Pro Imager to check

the stop position. Repeat the above steps until the desired position is

reached.

UP LIMIT

CONTROL

VIEWING

SURFACE

DOWN LIMIT

CONTROL

FIG.

TROUBLESHOOTING

SYMPTOM

1. Screen will not operate or will

not go “down”.

Motor does not hum.

Motor hums.

2. Screen will not move “up”.

Motor does not hum.

Motor hums.

3. Noise.

NOTE: Screen will operate with a

low-pitched hum.

4. Coasting.

5. Roller displaced from mounting

brackets.

6. Mask hangs crooked.

7. Mask does not stop at proper

position.

CAUSE

(a) Blown facility fuse.

(b) Tripped facility circuit breaker.

junction.

Power at junction box.

(d) Thermal overload tripped.

(e) Defective motor, limit switch or

capacitor.

(f) Temporary binding.

(a) Blown facility fuse.

(b) Tripped facility circuit breaker.

junction box.

Power at junction box.

(d) Thermal overload tripped.

(e) Defective motor, limit switch or

capacitor.

(f) Temporary binding.

(a) Grinding. Foreign object in screen

rubbing on roller or fabric.

(a) Defective brake.

(a) Pin end slipped out of nylon bearing.

(a) Screen not installed properly.

(b) Fabric is damaged.

(a) Limit switches out of adjustment.

SOLUTION

(a) Replace facility fuse.

(b) Reset circuit breaker.

connections. Recheck wiring. See

installation instructions.

“Down” Position

Check for power across black and white

leads.

(d) Let motor cool down for 15 minutes.

Try again.

(e) Replace motor assembly.

NOTE: Motor is a sealed assembly.

(f) With power “off“ turn roller by hand

to free binding.

(a) Replace facility fuse.

(b) Reset facility circuit breaker.

connections. See above.

“Up” Position

Check for power across red and white

leads.

(d) Let motor cool down for 15 minutes.

Try again.

(e) Replace motor assembly.

NOTE: Motor is a sealed assembly.

(f) With power “off”, turn roller by hand

to free binding.

(a) Remove.

(a) Replace motor assembly.

(a) Remove pin end mounting. Realign

motor in tube. Reattach pin end.

(a) Check for level and plumb.

(b) Replace fabric.

(a) See adjustment procedures.

Printed in U.S.A. 82391 Rev. 7/09

Autres manuels Da-Lite Écran de projection

Da-Lite

Da-Lite PERM WALL FRAME Manuel utilisateur

Da-Lite

Da-Lite ADVANTAGE ELECTROL Manuel utilisateur

Da-Lite

Da-Lite ASCENDER ELECTROL Manuel utilisateur

Da-Lite

Da-Lite TENSIONED CONTOUR ELECTROL Manuel utilisateur

Da-Lite

Da-Lite Da-Snap 74610 Manuel utilisateur

Da-Lite

Da-Lite TENSIONED DIRECTOR ELECTROL Manuel utilisateur

Da-Lite

Da-Lite Tensioned Advantage Deluxe Electrol Manuel utilisateur

Da-Lite

Da-Lite Cosmopolitan Electrol Manuel utilisateur

Da-Lite

Da-Lite DESIGNER ELECTROL Manuel utilisateur

Da-Lite

Da-Lite DESIGNER CONTOUR MANUAL Manuel utilisateur

Da-Lite

Da-Lite IDEA Screen Manuel utilisateur

Da-Lite

Da-Lite TENSIONED LARGE ADVANTAGE ELECTROL Manuel utilisateur

Da-Lite

Da-Lite Tensioned Conference Electrol Manuel utilisateur

Da-Lite

Da-Lite TENSIONED EXECUTIVE ELECTROL Manuel utilisateur

Da-Lite

Da-Lite Parallax Manuel utilisateur

Da-Lite

Da-Lite FullVision Manuel utilisateur

Da-Lite

Da-Lite Large Cosmopolitan Electrol Manuel utilisateur

Da-Lite

Da-Lite IMAGER Manuel utilisateur

Da-Lite

Da-Lite ADVANTAGE ELECTROL Manuel utilisateur

Da-Lite

Da-Lite Tensioned Cosmopolitan electrol Manuel utilisateur

Da-Lite

Da-Lite Polacoat Da-Plex Semi-Rigid Manuel utilisateur

Da-Lite

Da-Lite Slimline Electrol Manuel utilisateur

Da-Lite

Da-Lite IDEA Screen Manuel utilisateur

Da-Lite

Da-Lite Parallax Thin Manuel utilisateur

Manuels Écran de projection populaires d'autres marques

FART PRODUKT

FART PRODUKT Standard SCREEN Manuel utilisateur

Draper

Draper E Series Manuel

Elite Screens

Elite Screens Elite Tripod Series Manuel utilisateur

Laarhoven

Laarhoven Companion II Manuel utilisateur

Renogy

Renogy RMS-LFPS-US Manuel utilisateur

Samsung

Samsung S*H65* Manuel utilisateur

FONESTAR

FONESTAR PPTR-43100-FA Manuel utilisateur

Slide Clear

Slide Clear Varro XL Manuel utilisateur

Elite Screens

Elite Screens M85XWS1-SRM Manuel utilisateur

OS РХ-090Н Manuel utilisateur

Niko

Niko 10-845 Manuel utilisateur

Speaka Professional

Speaka Professional 2357532 Manuel d'utilisation

Sima

Sima XL-72 Manuel utilisateur

Jasic

Jasic EVO 2.0 ET-200P Manuel utilisateur

Elite Screens

Elite Screens Starling 2 Series Manuel utilisateur

InFocus

InFocus SC-WALL GRY-92H Manuel

Barco

Barco OverView MVL-615 Manuel utilisateur

Draper

Draper Envoy Manuel