D-Link DWL-2600AP Manuel utilisateur

This document will guide you through the

basic installation process for your new

D-Link Unied Wireless Access Point.

DWL-2600AP

Documentation also available on

CD and via the D-Link Website

Quick Installation Guide

802.11n Unied Access Point

POWER

LAN

2.4GHz

2  D-Link DWL-2600AP Quick Install Guide

ENGLISH

About This Guide

This installation guide provides basic instructions

for installing the DWL-2600AP Wireless Access

Point on your network. For additional information

about how to use the Access Point, please see

the User Manual, which is available on the CD

included in this package or from the D-Link

support website.

2.4 GHz – When this LED is lit up, the access

point’s 2.4 GHz radio is enabled. It will

blink when there is wireless trafc.

LAN – When this LED is lit up, the device’s

Ethernet port is connected to an active

router or switch. The light will blink

when there is trafc going through

the port.

POWER – When the LED is lit up, the access

point is powered and ready for use.

Unpacking the Product

System Requirements

Open the shipping carton and carefully unpack its

contents. Please consult the packing list located

in following information to make sure all items are

present and undamaged. If any item is missing

or damaged, please contact your local D-Link

reseller for replacement.

- DWL-2600AP 802.11n Unied Access Point

- Power Adapter

- Mounting Ring

- Ethernet Cable

- Console Cable*

- CD-ROM

Note: Using a power supply with a different

voltage than the one included with the

DWL-2600AP may cause damage and will void

the warranty for this product.

*The console cable is an optional accessory and

not included in the package in Armenia, Azerbaijan,

Belarus, Georgia, Israel, Kaliningrad, Kazakhstan,

Kyrgyzstan, Latvia, Lithuania, Moldova, Mongolia,

Russia, Turkey, Turkmenistan, Ukraine, and

Uzbekistan. If a cable is required, please contact

your reseller to order it (Model: ACS-AP-CONSOLE).

- CD-ROM Drive

- Windows®, Macintosh®, or Linux-based

operating system

- Ethernet port or installed Ethernet adapter

- Internet Explorer 7.0, Safari 5.0, Firefox 4.0,

or higher

Optional Accessories

- PoE Base Unit (Model: DPE-101GI)

Note: These accessories are not included in

the package. If any of these items are required,

please contact your reseller to order it.

Figure 2. DWL-2600AP Rear Panel

Hardware Overview

Figure 1. DWL-2600AP LEDs

Power Receptor

LAN Port (PoE)

Console Port

POWER

LAN

2.4GHz

LEDs

Interfaces

D-Link DWL-2600AP Quick Install Guide  3

ENGLISH

Power on the access point

To power on the DWL-2600AP, you can use ONE of

the following methods:

1. Connect the supplied power adapter

2. Plug one end of an Ethernet cable into the LAN

port of the DWL-2600AP and the other end into

a port on a PoE switch.

Congure the access point

To set up and manage the DWL-2600AP, use one

of the following methods:

• Manage the access point from the computer:

Connect the access point and your computer

directly via a straight-through Ethernet cable.

Mounting Options

You can mount a DWL-2600AP access point on any

of the following types of surfaces:

• Solid surface wall or ceiling

• Tabletop

Cable Requirement

Use a CAT 5 cable with an even sheath.

The Ethernet ports on the DWL-2600AP access

point cannot accept a CAT 5 cable that has an

uneven sheath; the RJ-45 connector on the cable

will not fit properly into the receptacle on the access

point.

Wall Installation Recommendations

If you plan to install the DWL-2600AP on a wall or

other vertical surfaces, orient the top of the access

point (the side with the LEDs) toward the intended

coverage area. The radio antennas transmit through

the top of the access point but not through the

bottom (where the bracket is).

Warning: The DWL-2600AP is designed to

receive PoE power only from an 802.3af-compliant

source, or from a D-Link-approved power injector.

Connecting an access point to a Power over

Ethernet (PoE) device that is not approved by

D-Link can damage the equipment.

• Manage the access point from the computer

via the Switch or Router: Connect the

access point and your computer to the same

switch or router.

Power Receptor

Reset Button

Installation

ComputerDWL-2600AP

Switch or Router

• Manage the access point from the computer

via the Unied Wireless Switch or Wireless

Controller: Connect the access point to

a Unied Wireless Switch or Wireless

Controller. Connect your computer to the

same network as that of the Unied Wireless

Switch or Wireless Controller.

ComputerDWL-2600AP

Unied Wireless Switch

Wireless Controller

Power Button

(For Power Adapter)

4  D-Link DWL-2600AP Quick Install Guide

ENGLISH

Solid Wall or Ceiling

Installation

1. Place the plastic wall mounting ring on a

wall or ceiling.

2. Mark the points where you will insert the

screws. Take out the mounting ring.

3. Drill holes in the marked points and

insert the plastic wall anchors.

4. Use the supplied screws to attach the

mounting ring to the wall.

5. Plug the CAT 5 cable into the LAN port on

the access point.

6. To attach the access point to the

mounting ring, rst locate the right side

of the access point that has a small lock

symbol on it, and make sure to line up

this side with the side of the mounting

ring that has Open - Lock written on it.

7. Twist clockwise to lock the access

point onto the ring. The lock symbol on

the access point must point directly to the

Close text on the mounting ring.

Figure 3. Insert screws through mounting ring

Figure 5. Insert access point into mounting ring

Figure 4. Plug cable into access point

POWER

LAN

2.4GHz

Autres manuels pour DWL-2600AP

Table des matières

Autres manuels D-Link Point d'accès sans fil

D-Link

D-Link DAP-3315 Manuel utilisateur

D-Link

D-Link NUCLIAS CONNECT Manuel utilisateur

D-Link

D-Link DAP-3310 Manuel utilisateur

D-Link

D-Link DAP-2590 - AirPremier N Dual Band PoE Access... Manuel utilisateur

D-Link

D-Link DBA-1510P Manuel utilisateur

D-Link

D-Link DAP-1150 Manuel utilisateur

D-Link

D-Link AirPlus DWL-900AP+ Manuel utilisateur

D-Link

D-Link DAP-2682 Manuel utilisateur

D-Link

D-Link DWL-8610AP Manuel utilisateur

D-Link

D-Link xtreme n duo dap-1522 Manuel utilisateur

D-Link

D-Link DWS-3024L Manuel utilisateur

D-Link

D-Link DAP-1513 Manuel utilisateur

D-Link

D-Link D DWL-8200AP DWL-8200AP Manuel utilisateur

D-Link

D-Link AirPremier N DAP-2310 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

D-Link

D-Link AirPlus DWL-900AP+ Manuel utilisateur

D-Link

D-Link AMPLIFI DAP-1525 Manuel utilisateur

D-Link

D-Link Air Premier DAP-2695 Manuel utilisateur

D-Link

D-Link DWR-730 Manuel utilisateur

D-Link

D-Link DAP-2553 - Wireless N Dual Band Gigabit Access... Manuel utilisateur

D-Link

D-Link DWL-700AP - Air - Wireless Bridge Manuel utilisateur

D-Link

D-Link D DWL-G700AP DWL-G700AP Manuel utilisateur

D-Link

D-Link DAP-2590 - AirPremier N Dual Band PoE Access... Manuel utilisateur

D-Link

D-Link DI-713 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur

EnGenius

EnGenius EAP350 Manuel utilisateur