D-Link DGS-1016D - Switch Manuel utilisateur

D-Link ™ DGS-1016D

DGS-1024D

16/24-Port 10/100/1000Mbps

Gigabit Ethernet Switch

Manual

Building Networks for People

RECYCLABLE

(November 2005)

P/N: 6DGS1024D.02G

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of D-Link Computer Corporation

is strictly forbidden.

Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Computer

Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the

marks and names or their products. D-Link Computer Corporation disclaims any proprietary interest in

trademarks and trade names other than its own.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide,

may cause harmful interference to radio communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be required to correct the interference at

his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference in which

case the user may be required to take adequate measures.

Warnung!

Dies ist ein Produkt der Klasse A. Im Wohnbereich kann dieses Produkt Funkstoerungen verursachen. In

diesem Fall kann vom Benutzer verlangt werden, angemessene Massnahmen zu ergreifen.

Precaución!

Este es un producto de Clase A. En un entorno doméstico, puede causar interferencias de radio, en cuyo

case, puede requerirse al usuario para que adopte las medidas adecuadas.

Attention!

Ceci est un produit de classe A. Dans un environnement domestique, ce produit pourrait causer des

interférences radio, auquel cas l`utilisateur devrait prendre les mesures adéquates.

Attenzione!

Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto può causare

interferenze radio, nel cui caso è possibile che l`utente debba assumere provvedimenti adeguati.

VCCI Warning

CONTENTS

PREFACE IV

NOTES,NOTICES,AND CAUTIONS ............................................................IV

SAFETY INSTRUCTIONS..............................................................................V

Safety Cautions................................................................................... v

General Precautions for Rack-Mountable Products.........................vii

Protecting Against Electrostatic Discharge ......................................ix

INTRODUCTION 10

SWITCH DESCRIPTION .............................................................................10

Switch Features ................................................................................11

Gigabit Ethernet Technology............................................................12

802.1P and QoS................................................................................12

FRONT-PANEL COMPONENTS..................................................................15

LED Indicators .................................................................................15

Cable Diagnostic..............................................................................16

POWER INPUT ON REAR PANEL...............................................................18

INSTALLATION 19

Package Contents .............................................................................19

BEFORE YOU CONNECT TO THE NETWORK............................................20

Mounting the Switch on a Rack ........................................................21

Attaching the Rubber Feet................................................................22

Provide for Adequate Ventilation .....................................................22

POWER ON...............................................................................................23

Power Failure...................................................................................23

CONNECTING THE SWITCH 24

Switch to End Node...........................................................................25

Switch to Hub or Switch....................................................................26

Connecting to Network Backbone or Server.....................................27

TECHNICAL SPECIFICATIONS 28

GLOSSARY 31

USA WARRANTY AND REGISTRATION INFORMATION 34

INTERNATIONAL OFFICES .......................................................................40

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Preface

The DGS-1016D/DGS-1024D Manual is divided into sections that describe the system

installation and operating instructions with examples.

Section 1, Introduction - A description of the physical features of the Switch,

including LED indicators, ports and panel descriptions.

Section 2, Installation – A description of the physical installation of the Switch,

mounting the Switch in a equipment rack and powering on the Switch.

Section 3, Connecting the Switch – A description of how to connect your Switch to

an end node, hub, another switch or backbone server.

Appendix Technical Specifications - The technical specifications of the DGS-

1016D/DGS-1024D.

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information

that helps you make better use of your device.

NOTICE: A NOTICE indicates either potential

damage to hardware or loss of data and tells you

how to avoid the problem.

CAUTION: A CAUTION indicates the potential for

property damage, personal injury or death.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to help protect your system

from potential damage. Throughout this safety section, the caution icon ( ) is used to indicate cautions

and precautions that you need to review and follow.

Safety Cautions

To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment,

observe the following precautions.

Observe and follow service markings. Do not service any product except as explained in your

system documentation. Opening or removing covers that are marked with the triangular

symbol with a lightning bolt may expose you to an electrical shock. Only a trained service

technician should service components inside these compartments.

If any of the following conditions occur, unplug the product from the electrical outlet and

replace the part or contact your trained service provider:

– The power cable, extension cable, or plug is damaged.

– An object has fallen into the product.

– The product has been exposed to water.

– The product has been dropped or damaged.

– The product does not operate correctly when you follow the operating

instructions.

•Keep your system away from radiators and heat sources. Also, do not block cooling

vents.

•Do not spill food or liquids on your system components, and never operate the product

in a wet environment. If the system gets wet, see the appropriate section in your

troubleshooting guide or contact your trained service provider.

•Do not push any objects into the openings of your system. Doing so can cause a fire or

an electric shock by shorting out interior components.

•Use the product only with approved equipment.

•Allow the product to cool before removing covers or touching internal components.

•Operate the product only from the type of external power source indicated on the

electrical ratings label. If you are not sure of the type of power source required, consult

your service provider or local power company.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Safety Instructions (continued)

•To help avoid damaging your system, be sure the voltage selection Switch (if provided)

on the power supply is set to match the power available at your location:

– 115 volts (V)/60 hertz (Hz) in most of North and South America and some Far

Eastern countries such as South Korea and Taiwan

– 100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan.

– 230 V/50 Hz in most of Europe, the Middle East, and the Far East.

•Also be sure that attached devices are electrically rated to operate with the power

available in your location.

•Use only approved power cable(s). If you have not been provided with a power cable

for your system or for any AC-powered option intended for your system, purchase a

power cable that is approved for use in your country. The power cable must be rated for

the product and for the voltage and current marked on the product's electrical ratings

label. The voltage and current rating of the cable should be greater than the ratings

marked on the product.

•To help prevent an electric shock, plug the system and peripheral power cables into

properly grounded electrical outlets. These cables are equipped with three-prong plugs

to help ensure proper grounding. Do not use adapter plugs or remove the grounding

prong from a cable. If you must use an extension cable, use a 3-wire cable with properly

grounded plugs.

•Observe extension cable and power strip ratings. Make sure that the total ampere rating

of all products plugged into the extension cable or power strip does not exceed 80

percent of the ampere ratings limit for the extension cable or power strip.

•To help protect your system from sudden, transient increases and decreases in electrical

power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).

•Position system cables and power cables carefully; route cables so that they cannot be

stepped on or tripped over. Be sure that nothing rests on any cables.

•Do not modify power cables or plugs. Consult a licensed electrician or your power

company for site modifications. Always follow your local/national wiring rules.

•When connecting or disconnecting power to hot-pluggable power supplies, if offered

with your system, observe the following guidelines:

– Install the power supply before connecting the power cable to the power supply.

– Unplug the power cable before removing the power supply.

– If the system has multiple sources of power, disconnect power from the system

by unplugging all power cables from the power supplies.

•Move products with care; ensure that all casters and/or stabilizers are firmly connected

to the system. Avoid sudden stops and uneven surfaces.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

vii

General Precautions for Rack-

Mountable Products

•Observe the following precautions for rack stability and safety. Also refer to the rack

installation documentation accompanying the system and the rack for specific caution

statements and procedures.

•Systems are considered to be components in a rack. Thus, "component" refers to any

system as well as to various peripherals or supporting hardware.

CAUTION: Installing systems in a rack without the front and

side stabilizers installed could cause the rack to tip over,

potentially resulting in bodily injury under certain

circumstances. Therefore, always install the stabilizers

before installing components in the rack.

After installing system/components in a rack, never pull

more than one component out of the rack on its slide

assemblies at one time. The weight of more than one

extended component could cause the rack to tip over and

may result in serious injury.

•Before working on the rack, make sure that the stabilizers are secured to the rack,

extended to the floor, and that the full weight of the rack rests on the floor. Install front

and side stabilizers on a single rack or front stabilizers for joined multiple racks before

working on the rack.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

viii

Safety Instructions (continued)

•Always load the rack from the bottom up, and load the heaviest item in the rack first.

•Make sure that the rack is level and stable before extending a component from the rack.

•Use caution when pressing the component rail release latches and sliding a component

into or out of a rack; the slide rails can pinch your fingers.

•After a component is inserted into the rack, carefully extend the rail into a locking

position, and then slide the component into the rack.

•Do not overload the AC supply branch circuit that provides power to the rack. The total

rack load should not exceed 80 percent of the branch circuit rating.

•Ensure that proper airflow is provided to components in the rack.

•Do not step on or stand on any component when servicing other components in a rack.

CAUTION: Never defeat the ground conductor or operate

the equipment in the absence of a suitably installed ground

conductor. Contact the appropriate electrical inspection

authority or an electrician if you are uncertain that suitable

grounding is available.

CAUTION: The system chassis must be positively

grounded to the rack cabinet frame. Do not attempt to

connect power to the system until grounding cables are

connected. Completed power and safety ground wiring

must be inspected by a qualified electrical inspector. An

energy hazard will exist if the safety ground cable is omitted

or disconnected.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Protecting Against Electrostatic Discharge

Static electricity can harm delicate components inside your system. To prevent static damage,

discharge static electricity from your body before you touch any of the electronic components,

such as the microprocessor. You can do so by periodically touching an unpainted metal

surface on the chassis.

You can also take the following steps to prevent damage from electrostatic discharge (ESD):

1. When unpacking a static-sensitive component from its shipping carton, do not

remove the component from the antistatic packing material until you are ready to

install the component in your system. Just before unwrapping the antistatic

packaging, be sure to discharge static electricity from your body.

2. When transporting a sensitive component, first place it in an antistatic container or

packaging.

3. Handle all sensitive components in a static-safe area. If possible, use antistatic

floor pads, workbench pads, and an antistatic grounding strap.

SECTION 1

Introduction

Switch Description

Switch Features

Ports

Front-Panel Components

LED Indicators

Power Input on Rear Panel

Switch Description

The 16-port DGS-1016D and 24-port DGS-1024D Switches provide

dedicated 10, 100 or 1000 Mbps Ethernet bandwidth on each port. The

ports will automatically detect the speed, duplex and MDI/MDIX status of

the device it is connecting to, and adjust these settings accordingly. The

Switch ports can be used to network computers, printers, servers, routers,

other switches or any device equipped with an Ethernet port. For best

performance, use Category 5 or better Ethernet cabling.

This stand-alone Switch is very easy to set up, there is no network

management required. Just power on the Switch and connect the cables.

Keep in mind however that the standard rules of Ethernet regarding cable

length apply to this and all Ethernet devices. The length of an Ethernet

cable from one device to another cannot exceed 100 meters (or 300 feet).

Autres manuels pour DGS-1016D - Switch

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels D-Link Changer

D-Link

D-Link DIS-100G-5PSW Manuel utilisateur

D-Link

D-Link DFE-916x Manuel utilisateur

D-Link

D-Link DGS-1016D - Switch Manuel utilisateur

D-Link

D-Link DSD-150 - SecureSpot Internet Security... Manuel utilisateur

D-Link

D-Link RG-S8614 Manuel d'installation et d'exploitation

D-Link

D-Link DES-1018MP Manuel utilisateur

D-Link

D-Link KVM-440 Manuel utilisateur

D-Link

D-Link DES-3350SR Manuel utilisateur

D-Link

D-Link DES-1018MP Manuel utilisateur

D-Link

D-Link DKVM-4U Manuel utilisateur

D-Link

D-Link DGS-3000-28SC Manuel utilisateur

D-Link

D-Link xStack DGS-3600 Series Manuel utilisateur

D-Link

D-Link DI-707 Manuel utilisateur

D-Link

D-Link DUB-H4 Manuel utilisateur

D-Link

D-Link 809TC - Hub - EN Manuel utilisateur

D-Link

D-Link EasySmart DGS-1100-08 Manuel utilisateur

D-Link

D-Link DES-1024D Manuel utilisateur

D-Link

D-Link DGS-1224T - Web Smart Switch Manuel utilisateur

D-Link

D-Link DES-3226 Manuel utilisateur

D-Link

D-Link DGS-1210 Series Manuel utilisateur

D-Link

D-Link DAS-3636 Manuel utilisateur

D-Link

D-Link xStack DGS-3420 Series Manuel utilisateur

D-Link

D-Link DKVM-2K Manuel utilisateur

D-Link

D-Link EasySmart DGS-1100-08PLV2 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Manuel utilisateur