D-Link DGS-1016D - Switch Manuel utilisateur

D-Link ™ DGS-1016D

DGS-1024D

16/24-Port 10/100/1000Mbps

Gigabit Ethernet Switch

Manual

Building Networks for People

RECYCLABLE

(February, 2005)

P/N : 6DGS1024D.01

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of D-Link Computer Corporation

is strictly forbidden.

Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Computer

Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the

marks and names or their products. D-Link Computer Corporation disclaims any proprietary interest in

trademarks and trade names other than its own.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s

guide, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference in which

case the user may be required to take adequate measures.

Warnung!

Dies ist ein Produkt der Klasse A. Im Wohnbereich kann dieses Produkt

Funkstoerungen verursachen. In diesem Fall kann vom Benutzer verlangt werden,

angemessene Massnahmen zu ergreifen.

Precaución!

Este es un producto de Clase A. En un entorno doméstico, puede causar interferencias

de radio, en cuyo case, puede requerirse al usuario para que adopte las medidas

adecuadas.

Attention!

Ceci est un produit de classe A. Dans un environnement domestique, ce produit

pourrait causer des interférences radio, auquel cas l`utilisateur devrait prendre les

mesures adéquates.

Attenzione!

Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto può causare

interferenze radio, nel cui caso è possibile che l`utente debba assumere provvedimenti adeguati.

VCCI Warning

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

CONTENTS

PREFACE...................................................................................I

NOTES, NOTICES, AND CAUTIONS...........................................I

SAFETY INSTRUCTIONS.......................................................... II

INTRODUCTION........................................................................1

ETHERNET TECHNOLOGY..........................................................................1

SWITCHING TECHNOLOGY.........................................................................3

SWITCH DESCRIPTION...............................................................................4

FRONT-PANEL COMPONENTS....................................................................6

REAR PANEL DESCRIPTION .......................................................................9

INSTALLATION.......................................................................10

PACKAGE CONTENTS ..............................................................................11

BEFORE YOU CONNECT TO THE NETWORK ..............................................11

MOUNTING THE SWITCH ON A RACK........................................................12

ATTACHING THE RUBBER FEET ...............................................................12

PROVIDE FOR ADEQUATE VENTILATION ..................................................13

POWER ON.............................................................................................14

CONNECTING THE SWITCH ..................................................15

SWITCH TO END NODE ...........................................................................15

SWITCH TO HUB OR SWITCH....................................................................17

CONNECTING TO NETWORK BACKBONE OR SERVER.................................18

TECHNICAL SPECIFICATIONS..................................................................19

GLOSSARY................................................................................................21

WARRANTY ..............................................................................................25

WARRANTY (USA ONLY)........................................................................29

REGISTRATION INFORMATION ................................................................35

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Preface

The DGS-1016D/DGS-1024D Manual is divided into sections that describe the system

installation and operating instructions with examples.

Section 1, Introduction - A description of the physical features of the Switch,

including LED indicators, ports, and panel descriptions.

Section 2, Installation – A description of the physical installation of the Switch,

including connecting the Switch to the network and connecting stacked Switch groups.

Section 3, Connecting the Switch – A description of how to connect your Switch to

an end node, hub, Switch, or backbone server.

Appendix A, Technical Specifications - The technical specifications of the DGS-

1016D/DGS-1024D.

Glossary – Lists definitions for terms and acronyms used in this document.

Index – Index of relevant terms in the DGS-1016D/DGS-1024D Manual.

Intended Readers

The DGS-1016D/DGS-1024D Manual contains information for setup and management of the

DGS-1016D/DGS-1024D Switch. This manual is intended for network managers familiar

with network management concepts and terminology.

Notes, Notices, and Cautions

NOTE: A NOTE indicates important

information that helps you make better

use of your device.

NOTICE: A NOTICE indicates either

potential damage to hardware or loss of

data and tells you how to avoid the

problem.

CAUTION: A CAUTION indicates the

potential for property damage, personal

injury, or death.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to help protect

your system from potential damage. Throughout this safety section, the caution icon ( ) is

used to indicate cautions and precautions that you need to review and follow.

Safety Cautions

To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment,

observe the following precautions.

Observe and follow service markings. Do not service any product except as explained in your

system documentation. Opening or removing covers that are marked with the triangular

symbol with a lightning bolt may expose you to an electrical shock. Only a trained service

technician should service components inside these compartments.

If any of the following conditions occur, unplug the product from the electrical outlet and

replace the part or contact your trained service provider:

– The power cable, extension cable, or plug is damaged.

– An object has fallen into the product.

– The product has been exposed to water.

– The product has been dropped or damaged.

– The product does not operate correctly when you follow the operating

instructions.

• Keep your system away from radiators and heat sources. Also, do not block

cooling vents.

• Do not spill food or liquids on your system components, and never operate the

product in a wet environment. If the system gets wet, see the appropriate section

in your troubleshooting guide or contact your trained service provider.

• Do not push any objects into the openings of your system. Doing so can cause a

fire or an electric shock by shorting out interior components.

• Use the product only with approved equipment.

• Allow the product to cool before removing covers or touching internal

components.

• Operate the product only from the type of external power source indicated on the

electrical ratings label. If you are not sure of the type of power source required,

consult your service provider or local power company.

• To help avoid damaging your system, be sure the voltage selection Switch (if

provided) on the power supply is set to match the power available at your

location:

– 115 volts (V)/60 hertz (Hz) in most of North and South America and some Far

Eastern countries such as South Korea and Taiwan.

– 100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan.

– 230 V/50 Hz in most of Europe, the Middle East, and the Far East.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

iii

• Also be sure that attached devices are electrically rated to operate with the power

available in your location.

Safety Instructions (continued)

• Use only approved power cable(s). If you have not been provided with a power

cable for your system or for any AC-powered option intended for your system,

purchase a power cable that is approved for use in your country. The power cable

must be rated for the product and for the voltage and current marked on the

product's electrical ratings label. The voltage and current rating of the cable

should be greater than the ratings marked on the product.

• To help prevent an electric shock, plug the system and peripheral power cables

into properly grounded electrical outlets. These cables are equipped with three-

prong plugs to help ensure proper grounding. Do not use adapter plugs or remove

the grounding prong from a cable. If you must use an extension cable, use a 3-

wire cable with properly grounded plugs.

• Observe extension cable and power strip ratings. Make sure that the total ampere

rating of all products plugged into the extension cable or power strip does not

exceed 80 percent of the ampere ratings limit for the extension cable or power

strip.

• To help protect your system from sudden, transient increases and decreases in

electrical power, use a surge suppressor, line conditioner, or uninterruptible power

supply (UPS).

• Position system cables and power cables carefully; route cables so that they

cannot be stepped on or tripped over. Be sure that nothing rests on any cables.

• Do not modify power cables or plugs. Consult a licensed electrician or your power

company for site modifications. Always follow your local/national wiring rules.

• When connecting or disconnecting power to hot-pluggable power supplies, if

offered with your system, observe the following guidelines:

– Install the power supply before connecting the power cable to the power supply.

– Unplug the power cable before removing the power supply.

– If the system has multiple sources of power, disconnect power from the system

unplugging all power cables from the power supplies.

• Move products with care; ensure that all casters and/or stabilizers are firmly

connected to the system. Avoid sudden stops and uneven surfaces.

General Precautions for Rack-

Mountable Products

Observe the following precautions for rack stability and safety. Also refer to the rack

installation documentation accompanying the system and the rack for specific caution

statements and procedures.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Systems are considered to be components in a rack. Thus, "component" refers to any system

as well as to various peripherals or supporting hardware.

CAUTION: Installing systems in a rack without the front and

side stabilizers installed could cause the rack to tip over,

potentially resulting in bodily injury under certain

circumstances. Therefore, always install the stabilizers

before installing components in the rack.

After installing system/components in a rack, never pull

more than one component out of the rack on its slide

assemblies at one time. The weight of more than one

extended component could cause the rack to tip over and

may result in serious injury.

• Before working on the rack, make sure that the stabilizers are secured to the rack,

extended to the floor, and that the full weight of the rack rests on the floor. Install

front and side stabilizers on a single rack or front stabilizers for joined multiple

racks before working on the rack.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Safety Instructions (continued)

Always load the rack from the bottom up, and load the heaviest item in the rack first.

Make sure that the rack is level and stable before extending a component from the rack.

Use caution when pressing the component rail release latches and sliding a component into or

out of a rack; the slide rails can pinch your fingers.

After a component is inserted into the rack, carefully extend the rail into a locking position,

and then slide the component into the rack.

Do not overload the AC supply branch circuit that provides power to the rack. The total rack

load should not exceed 80 percent of the branch circuit rating.

Ensure that proper airflow is provided to components in the rack.

Do not step on or stand on any component when servicing other components in a rack.

Protecting Against Electrostatic Discharge

Static electricity can harm delicate components inside your system. To prevent static damage,

discharge static electricity from your body before you touch any of the electronic

components, such as the microprocessor. You can do so by periodically touching an

unpainted metal surface on the chassis.

NOTE: A qualified electrician must perform all

connections to DC power and to safety grounds. All

electrical wiring must comply with applicable local or

national codes and practices.

CAUTION: Never defeat the ground conductor or operate

the equipment in the absence of a suitably installed ground

conductor. Contact the appropriate electrical inspection

authority or an electrician if you are uncertain that suitable

grounding is available.

CAUTION: The system chassis must be positively

grounded to the rack cabinet frame. Do not attempt to

connect power to the system until grounding cables are

connected. Completed power and safety ground wiring

must be inspected by a qualified electrical inspector. An

energy hazard will exist if the safety ground cable is omitted

or disconnected.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

You can also take the following steps to prevent damage from electrostatic discharge (ESD):

1. When unpacking a static-sensitive component from its shipping carton, do not

remove the component from the antistatic packing material until you are ready to

install the component in your system. Just before unwrapping the antistatic

packaging, be sure to discharge static electricity from your body.

2. When transporting a sensitive component, first place it in an antistatic container or

packaging.

3. Handle all sensitive components in a static-safe area. If possible, use antistatic

floor pads, workbench pads, and an antistatic grounding strap.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

SECTION 1

Introduction

Ethernet Technology

Switch Description

Features

Ports

Front-Panel Components

Ethernet Technology

Fast Ethernet Technology

The growing importance of LANs and the increasing

complexity of desktop computing applications are fueling the

need for high performance networks. A number of high-speed

LAN technologies are proposed to provide greater bandwidth

and improve client/server response times. Among them, Fast

Ethernet, or 100BASE-T, provides a non-disruptive, smooth

evolution from 10BASE-T technology.

100Mbps Fast Ethernet is a standard specified by the IEEE

802.3 LAN committee. It is an extension of the 10Mbps

Ethernet standard with the ability to transmit and receive data

at 100Mbps, while maintaining the Carrier Sense Multiple

Access with Collision Detection (CSMA/CD) Ethernet

protocol.

Autres manuels pour DGS-1016D - Switch

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels D-Link Changer

D-Link

D-Link DUB-2240 - Wireless USB Hub Manuel utilisateur

D-Link

D-Link xStack DES-3810 Manuel utilisateur

D-Link

D-Link DES-108 Manuel utilisateur

D-Link

D-Link EasySmart DGS-1100-16 Manuel utilisateur

D-Link

D-Link DGS-1008G Manuel utilisateur

D-Link

D-Link DGS-1008P Manuel utilisateur

D-Link

D-Link DES-1018P Manuel utilisateur

D-Link

D-Link DKVM-IP8 Manuel utilisateur

D-Link

D-Link DGS-1010MP Manuel utilisateur

D-Link

D-Link DES-7000 Series Manuel utilisateur

D-Link

D-Link DES-1005E Manuel utilisateur

D-Link

D-Link DUB-2340 Manuel utilisateur

D-Link

D-Link DES-1018DG Manuel utilisateur

D-Link

D-Link DES-1016D - Switch Manuel utilisateur

D-Link

D-Link DGS-3000 series Manuel

D-Link

D-Link DES-3326 Manuel utilisateur

D-Link

D-Link DFE-550TX Manuel utilisateur

D-Link

D-Link DWS-3160-24TC Mode d’emploi

D-Link

D-Link DES-3252P - Web Smart Switch Manuel utilisateur

D-Link

D-Link xStack DGS-3427 Manuel utilisateur

D-Link

D-Link DGS-1016A Manuel utilisateur

D-Link

D-Link xStack DGS-3420-28SC Manuel utilisateur

D-Link

D-Link xStack DGS-3324SRi Manuel utilisateur

D-Link

D-Link DXS-3600-EM-8XS Manuel

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Manuel utilisateur