D-Link DES-3028 Manuel utilisateur

CLI Reference Manual

Product Model : DES-3028/DES-3028P/DES-3028G/DES-3052/DES-3052P

Managed 10/100Mbps Fast Ethernet Switch

Release 2

_________________________________________________________________________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of D-Link Computer Corporation is strictly forbidden.

Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Computer Corporation; Microsoft and

Windows are registered trademarks of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or

their products. D-Link Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its

own.

January 2009 P/N 651ES3028025G

Table of Contents

INTRODUCTION ..........................................................................................................................................................1

USING THE CONSOLE CLI.........................................................................................................................................3

COMMAND SYNTAX...................................................................................................................................................7

BASIC SWITCH COMMANDS.....................................................................................................................................9

MODIFY BANNER AND PROMPT COMMANDS .....................................................................................................22

SWITCH PORT COMMANDS....................................................................................................................................25

PORT SECURITY COMMANDS................................................................................................................................29

NETWORK MANAGEMENT (SNMP) COMMANDS .................................................................................................33

SWITCH UTILITY COMMANDS ................................................................................................................................53

NETWORK MONITORING COMMANDS..................................................................................................................62

MULTIPLE SPANNING TREE PROTOCOL (MSTP) COMMANDS .........................................................................74

FORWARDING DATABASE COMMANDS...............................................................................................................87

BROADCAST STORM CONTROL COMMANDS.....................................................................................................94

COS COMMANDS......................................................................................................................................................98

PORT MIRRORING COMMANDS...........................................................................................................................112

VLAN COMMANDS .................................................................................................................................................115

LINK AGGREGATION COMMANDS.......................................................................................................................122

BASIC IP COMMANDS............................................................................................................................................127

IGMP SNOOPING COMMANDS..............................................................................................................................130

DHCP RELAY...........................................................................................................................................................141

802.1X COMMANDS................................................................................................................................................148

ACCESS CONTROL LIST (ACL) COMMANDS......................................................................................................168

TIME RANGE COMMANDS.....................................................................................................................................182

SAFEGUARD ENGINE COMMANDS......................................................................................................................184

TRAFFIC SEGMENTATION COMMANDS..............................................................................................................186

TIME AND SNTP COMMANDS...............................................................................................................................188

ARP COMMANDS....................................................................................................................................................195

ROUTING TABLE COMMANDS..............................................................................................................................199

MAC NOTIFICATION COMMANDS ........................................................................................................................201

ACCESS AUTHENTICATION CONTROL COMMANDS........................................................................................205

SSH COMMANDS....................................................................................................................................................226

SSL COMMANDS ....................................................................................................................................................233

D-LINK SINGLE IP MANAGEMENT COMMANDS.................................................................................................239

SMTP COMMANDS .................................................................................................................................................250

POE COMMANDS....................................................................................................................................................254

CABLE DIAGNOSTICS COMMANDS.....................................................................................................................259

DHCP LOCAL RELAY COMMANDS ......................................................................................................................260

GRATUITOUS ARP COMMANDS...........................................................................................................................262

VLAN TRUNKING COMMANDS .............................................................................................................................266

QINQ COMMANDS..................................................................................................................................................270

ASYMMETRIC VLAN COMMANDS........................................................................................................................273

MLD SNOOPING COMMANDS...............................................................................................................................275

IGMP SNOOPING MULTICAST VLAN COMMANDS.............................................................................................282

LIMITED IP MULTICAST ADDRESS COMMANDS................................................................................................287

LLDP COMMANDS..................................................................................................................................................292

DOS PREVENTION COMMANDS...........................................................................................................................311

IP-MAC-PORT BINDING COMMANDS...................................................................................................................316

LOOPBACK DETECTION COMMANDS.................................................................................................................327

TECHNICAL SUPPORT COMMANDS....................................................................................................................331

COMMAND HISTORY LIST.....................................................................................................................................334

TECHNICAL SPECIFICATIONS..............................................................................................................................338

ARP PACKET CONTENT ACL................................................................................................................................344

PASSWORD RECOVERY PROCEEDURE.............................................................................................................352

DES-3028 DES-3028P DES-3028G DES-3052 DES-3052P Layer 2 Fast Ethernet Switch CLI Reference Manual

INTRODUCTION

The Switch can be managed through the Switch’s serial port, Telnet, or the Web-based management agent. The Command Line

Interface (CLI) can be used to configure and manage the Switch via the serial port or Telnet interfaces.

This manual provides a reference for all of the commands contained in the CLI. Configuration and management of the Switch via

the Web-based management agent is discussed in the Manual. This manual provides a reference for all of the commands contained

in the CLI for members of this series, including the DES-3028, DES-3028P, DES-3028G, DES-3052, and DES-3052P. Examples

present in this manual may refer to any member of this series and may show different port counts, but are universal to this series

of switches, unless otherwise stated. Configuration and management of the Switch via the Web-based management agent is

discussed in the User’s Guide.

Accessing the Switch via the Serial Port

The Switch’s serial port’s default settings are as follows:

9600 baud

no parity

8 data bits

1 stop bit

A computer running a terminal emulation program capable of emulating a VT-100 terminal and a serial port configured as above

are then connected to the Switch’s serial port via an RS-232 DB-9 cable.

With the serial port properly connected to a management computer, the following screen should be visible. If this screen does not

appear, try pressing Ctrl+r to refresh the console screen.

DES-3028P Fast Ethernet Switch Command Line Interface

Firmware: Build 2.00.B23

username:

Figure 1-1. Initial CLI screen

There is no initial username or password. Just press the Enter key twice to display the CLI input cursor DES-3028P:4#.This is

the command line where all commands are input.

DES-3028 DES-3028P DES-3028G DES-3052 DES-3052P Layer 2 Fast Ethernet Switch CLI Reference Manual

Setting the Switch’s IP Address

Each Switch must be assigned its own IP Address, which is used for communication with an SNMP network manager or other

TCP/IP application (for example BOOTP, TFTP). The Switch’s default IP address is 10.90.90.90. Users can change the default

Switch IP address to meet the specification of your networking address scheme.

The Switch is also assigned a unique MAC address by the factory. This MAC address cannot be changed, and can be found on the

initial boot console screen – shown below.

Boot Procedure V1.00.06

--------------------------------------------------------------------------

Power On Self Test.................................100%

MAC Address : 00-21-91-98-60-77

H/W Version : A1

Please wait, loading V2.00.B23 Runtime image........100%

Figure 1-2. Boot screen

The Switch’s MAC address can also be found in the Web management program on the Switch Information (Basic Settings)

window on the Configuration menu.

The IP address for the Switch must be set before it can be managed with the Web-based manager. The Switch IP address can be

automatically set using BOOTP or DHCP protocols, in which case the actual address assigned to the Switch must be known.

The IP address may be set using the Command Line Interface (CLI) over the console serial port as follows:

1. Starting at the command line prompt, enter the commands config ipif System ipaddress

xxx.xxx.xxx.xxx/yyy.yyy.yyy.yyy. Where the x’s represent the IP address to be assigned to the IP interface named

System and the y’s represent the corresponding subnet mask.

2. Alternatively, users can enter config ipif System ipaddress xxx.xxx.xxx.xxx/z. Where the x’s represent the IP address to

be assigned to the IP interface named System and the zrepresents the corresponding number of subnets in CIDR

notation.

The IP interface named System on the Switch can be assigned an IP address and subnet mask which can then be used to connect a

management station to the Switch’s Telnet or Web-based management agent.

DES-3028P:4#config ipif System ipaddress 10.73.21.11/255.0.0.0

Command: config ipif System ipaddress 10.73.21.11/8

Success.

DES-3028P:4#

Figure 1-3. Assigning an IP Address

In the above example, the Switch was assigned an IP address of 10.90.90.91 with a subnet mask of 255.0.0.0. The system message

Success indicates that the command was executed successfully. The Switch can now be configured and managed via Telnet,

SNMP MIB browser and the CLI or via the Web-based management agent using the above IP address to connect to the Switch.

DES-3028 DES-3028P DES-3028G DES-3052 DES-3052P Layer 2 Fast Ethernet Switch CLI Reference Manual

USING THE CONSOLE CLI

The DES-3028/28P/28G/52/52P support a console management interface that allows the user to connect to the Switch’s

management agent via a serial port and a terminal or a computer running a terminal emulation program. The console can also be

used over the network using the TCP/IP Telnet protocol. The console program can be used to configure the Switch to use an

SNMP-based network management software over the network.

This chapter describes how to use the console interface to access the Switch, change its settings, and monitor its operation.

Note: Switch configuration settings are saved to non-volatile RAM using the save command. The current

configuration will then be retained in the Switch’s NV-RAM, and reloaded when the Switch is rebooted. If

the Switch is rebooted without using the save command, the last configuration saved to NV-RAM will be

loaded.

Connecting to the Switch

The console interface is used by connecting the Switch to a VT100-compatible terminal or a computer running an ordinary

terminal emulator program (e.g., the HyperTerminal program included with the Windows operating system) using an RS-232C

serial cable. Your terminal parameters will need to be set to:

VT-100 compatible

9600 baud

8 data bits

No parity

One stop bit

No flow control

Users can also access the same functions over a Telnet interface. Once users have set an IP address for your Switch, users can use

a Telnet program (in VT-100 compatible terminal mode) to access and control the Switch. All of the screens are identical, whether

accessed from the console port or from a Telnet interface.

After the Switch reboots and users have logged in, the console looks like this:

DES-3028P Fast Ethernet Switch Command Line Interface

Firmware: Build 2.00.B23

username:

Figure 2-1. Initial Console Screen after logging in

Commands are entered at the command prompt, DES-3028P:4#.

There are a number of helpful features included in the CLI. Entering the ?command will display a list of all of the top-level

commands.

DES-3028 DES-3028P DES-3028G DES-3052 DES-3052P Layer 2 Fast Ethernet Switch CLI Reference Manual

cable_diag ports

clear

clear address_binding dhcp_snoop binding_entry ports

clear arptable

clear counters

clear dos_prevention counters

clear fdb

clear igmp_snooping data_driven_group

clear log

clear port_security_entry port

config 802.1p default_priority

config 802.1p user_priority

config 802.1x auth_mode

config 802.1x auth_parameter ports

config 802.1x auth_protocol

config 802.1x capability ports

config 802.1x guest_vlan ports

config 802.1x init

config 802.1x reauth

config access_profile profile_id

CTRL+C ESC q Quit SPACE n Next Page ENTER Next Entry a All

Figure 2-2. The ? Command

When users enter a command without its required parameters, the CLI will prompt users with Next possible completions:

message.

DES-3028P:4#config account

Command: config account

Next possible completions:

DES-3028P:4#

Figure 2-3. Example Command Parameter Help

In this case, the command config account was entered with the parameter <username>. The CLI will then prompt users to enter

the <username> with the message, Next possible completions:. Every command in the CLI has this feature, and complex

commands have several layers of parameter prompting.

In addition, after typing any given command plus one space, users can see all of the next possible sub-commands, in sequential

order, by repeatedly pressing the Tab key.

To re-enter the previous command at the command prompt, press the up arrow cursor key. The previous command will appear at

the command prompt.

DES-3028 DES-3028P DES-3028G DES-3052 DES-3052P Layer 2 Fast Ethernet Switch CLI Reference Manual

DES-3028P:4#config account

Command: config account

Next possible completions:

DES-3028P:4#config account

Command: config account

Next possible completions:

DES-3028P:4#

Figure 2-4. Using the Up Arrow to Re-enter a Command

In the above example, the command config account was entered without the required parameter <username>, the CLI returned

the Next possible completions: <username> prompt. The up arrow cursor control key was pressed to re-enter the previous

command (config account) at the command prompt. Now the appropriate username can be entered and the config account

command re-executed.

All commands in the CLI function in this way. In addition, the syntax of the help prompts are the same as presented in this manual

angle brackets < > indicate a numerical value or character string, braces { } indicate optional parameters or a choice of

parameters, and brackets [ ] indicate required parameters.

If a command is entered that is unrecognized by the CLI, the top-level commands will be displayed under the Available

commands: prompt.

DES-3028P:4#the

Available commands:

.. ? cable_diag clear

config create debug delete

dir disable download enable

reconfig reset save show

smtp telnet traceroute upload

DES-3028P:4#

Figure 2-5. The Next Available Commands Prompt

The top-level commands consist of commands such as show or config. Most of these commands require one or more parameters

to narrow the top-level command. This is equivalent to show what? or config what? Where the what? is the next parameter.

For example, if users enter the show command with no additional parameters, the CLI will then display all of the possible next

parameters.

Autres manuels pour DES-3028

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels D-Link Changer

D-Link

D-Link DGS-1250 Series Manuel

D-Link

D-Link DGS-108 Manuel utilisateur

D-Link

D-Link DES-1526 Manuel utilisateur

D-Link

D-Link DES-1228 - Web Smart Switch Manuel utilisateur

D-Link

D-Link DGS-1100-08V2 Manuel utilisateur

D-Link

D-Link xStack DES-3552 Series Manuel utilisateur

D-Link

D-Link DGS-1005D - Switch Manuel utilisateur

D-Link

D-Link DES-1008D Manuel utilisateur

D-Link

D-Link xStack DGS-3120-24PC Manuel utilisateur

D-Link

D-Link DXS-3250 - xStack Switch - Stackable Manuel utilisateur

D-Link

D-Link xStack DGS-3620-52P Manuel utilisateur

D-Link

D-Link xStack Manuel utilisateur

D-Link

D-Link DES-7210-BASE Manuel utilisateur

D-Link

D-Link 55443 Manuel utilisateur

D-Link

D-Link DFE-550TX Manuel utilisateur

D-Link

D-Link DGS-1520-28MP Manuel utilisateur

D-Link

D-Link DGS-3100 SERIES Manuel utilisateur

D-Link

D-Link DGS-1005P Manuel utilisateur

D-Link

D-Link xStack DGS-3426P Manuel utilisateur

D-Link

D-Link DES-1228 - Web Smart Switch Manuel utilisateur

D-Link

D-Link DSS-16+ Manuel utilisateur

D-Link

D-Link DGS-1100-05PDV2 Manuel utilisateur

D-Link

D-Link KVM-222 Manuel utilisateur

D-Link

D-Link DFE-2624 - Hub - Stackable Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Manuel utilisateur