D-Link DFL-260 - NetDefend - Security Appliance Manuel utilisateur
Network
Security UTM Firewall
This Quick Guide will guide you through the installation Process. You are
only moments away from using your new D-Link Network Security Product
Building Networks for People
DFL-260
1.Before You Begin
1.1 Check Your Package Contents....................................................................1
2.Indentifying Components
2.1 FrontView.................................................................................................2
2.2 Rear View.................................................................................................2
2.3 LED Indicators...........................................................................................3
2.4 DefaultInterface AttributeDefinition..........................................................3
3.Connecting the DFL-260
3.1 Setting up Firewall to your Network...........................................................4
4.Configure DFL-260
4.1 Configure your Computer’s IP...................................................................5
4.2 UsingtheSetupWizard..............................................................................6
5.Appendix
5.1 How to Configure Static IP Manually on Microsoft Windows XP...............14
5.2 How to Configure Static IP Manually on Apple MAC OS X............................15
6.Statement
DFL-260 Quick Installation Guide
1.1 Check Your Package Contents
Your NetDefend Network Security UTM Firewall package should
contain all the items listed below. If any of these items is found
damaged or missing in your package, report it to your reseller
immediately for replacement.
DFL-260 NetDefend™ Network Security UTM Firewall
5V DC Power Adapter
Console Cable (RS-232 cable)
Ethernet (CAT5 UTP/Straight Through) Cable
Ethernet (CAT5 UTP/Cross-over) Cable
CD-ROM (containing QIG/Manual )
2 x NetDefend UTM Subscription (IPS & Anti-Virus)
DFL-260
Before You Begin 1
01
DFL-260
Power Adapter
Console Cable CD-ROM
Ethernet Cable
(Cross-over)
Ethernet Cable
(Straight-Through)
NetDefend UTM
Subscription
Identifying Components 2
The following illustrates the front panel of the DFL-260 and
explains the front panel’s key components:
2.1 Front View
02
1. Power LED
2. Status LED
3. WAN LED
4. DMZ LED
5. LAN LED
Power indication of the DFL-260.
System status indication of the DFL-260.
WAN port status indication of the DFL-260.
DMZ port status indication of the DFL-260.
LAN port status indication of the DFL-260.
Note:
WAN interface do not support Auto MDI/MDI-X
(Automatic cable detection for Straight-through and Crossover
function).
1 2 3 4 5
2.2 Rear View
1. Console Port
2. LAN Ports
3. DMZ Port
4. WAN Port
5. Reset
6. Power Receptor
Connects to RS-232 console cable that connects to PC.
These are for the connection of Ethernet cables to the internal network.
This is for the connection of an Ethernet cable to an DMZ network.
This is for the connection of an Ethernet cable to a Cable or DSL modem.
This is for resetting system conguration to factory defaults.
This is for the connection of the power adaper to a wall outlet or power strip.
1 3 4 62 5
2.4 Default Interface Attribute Definition
Note:
For security reason, default only allow LAN interface (192.168.1.1)
that can login into rewall GUI from Web browser. You also can
modify this conguration after login into rewall GUI. About the
detail set up procedure, please refer to the user’s manual.
DFL-260 Quick Installation Guide
03
Wording on
Front plate
Default name
in rewall
Default interface
type denition
Default interface
IP Address
Default
DHCP Status
WAN WAN DHCP client N/A Enabled
DMZ DMZ Static IP 172.17.100.254/24 Disable
Ports: 1~4 LAN Static IP 192.168.1.1/24 Disable
2.3 LED Indicators
Status
Solid green
Light off
Solid green
Light off
Blinking green
Solid green
Blinking green
Light off
Solid green
Blinking green
Light off
Solid green
Blinking green
Light off
Description
The device is powered on.
The device is powered off.
System is operating properly.
The device is not working.
System is defective, such rmware
upgrade fail.
Link present
Port is sending or receiving data.
No link
Link present
Port is sending or receiving data.
No link
Link present
Port is sending or receiving data.
No link
Color
Green
Green
Green
Green
Green
LED
Power
Status
WAN
DMZ
LAN
3.1 Connecting Firewall to Your Network
A. First, connect the power cord to the receptor on the back panel
of the DFL-260 and then plug the other end of the power cord
to a wall outlet or power strip. After the power LED turns on, you
need to wait 1-2 minutes for the DFL-260 to boot up completely.
B. Connect an Ethernet cable from the DFL-260 to your Cable/
DSL modem. If the Cable/DSL modem is powered on, wait
for the WAN LED on the DFL-260 to light up to show a proper
connection. Otherwise, turn off your Cable/DSL modem, connect
the Ethernet cable from the DFL-260 to your Cable/DSL modem,
and turn on the Cable/DSL modem. Some Cable/DSL modems
may not have an on/off switch and will require you to unplug the
power adapter.
Note:
The default management IP address of the DFL-260 is
192.168.1.1. If you have are using a router that uses DHCP,
there may be a conict if the router uses the same IP address as
the DFL-260. If this is the case, either disconnect the DFL-260
from the router and change the management IP address of the
DFL-260, or change the DHCP settings on your router.
C. Insert an Ethernet cable to the LAN1 port on the rear panel of
the DFL-260 and connect it to a port on your network hub or
switch. The LAN port LED light on the DFL-260 will illuminate to
indicate proper connection
D. Connecting the computer that you will use to congure the
DFL-260 to the network hub or switch.
Connecting the DFL-260 3
04
4.1 Configure Your Computer’s IP Address
Make sure that the network adapter in your computer is congured
to use a static IP address with 192.168.1.1 as default gateway and
255.255.255.0 as netmask. Instructions on how to congure the
network adapter can be found in the appendix.
When you have completed the steps in this Quick Installation
Guide, your connected network should look similar to this:
Configure DFL-260 4
05
Cable/DSL Modem
DFL-260
Switch
Internal
Network
DMZ
Network
(optional)
Computer1 Computer2
4.2 Using the Setup Wizard
The DFL-260 provides Web based conguration. You can
congure your DFL-260 through Internet Explorer 6 and later
or Firefox 1.0 and later browser in MS Windows, Macintosh or
UNIX based platforms. Activate your browser. Then type the
IP address of the DFL-260 into the Location/Address eld and
press “Enter.”
(The IP Address shown in the example above is the default
setting. If you have changed the IP Address of the DFL-260
to conform to a network, then input that IP Address in the web
browser, instead of the default IP Address shown.)
Log on to the DFL-260 web interface.
To start using the DFL-260 web interface you need to log on
using the default username and password.
DFL-260 Quick Installation Guide
Open your Web
browser and type
https://192.168.1.1 /
into the URL address
box. Then press the
Enter or Return key.
Type the default
Username/Password
Username: admin
Pasword: admin
and click Login
06
Note:
DFL-260 allows either HTTP or a secure HTTPS connection from
any management host. However, for security reasons, by default
only a secure HTTPS connection is allowed. For more information
about conguring connection setting, please refer to the Firewall
User Manual.
Note:
In order for the Setup Wizard to run properly, make sure IE Pop-Up
Blocker is turned off or click Temporarily Allow Pop-ups when the
Information Bar in IE noties you that a pop-up has been blocked.
Step1 - Welcome to the DFL-260 setup wizard!
Step2 - Set up rewall administrator password
First Enter the
username that you want
to use for the admin
account.
Enter the password
that you want to use
for the admin account.
DFL-260 Quick Installation Guide
This wizard will guide
you through the setup of
your DFL-260
Click Next
07
Click Next
2
Step 3 - Set up time and date
Click Set time and date
button for setting device
08
Click Next
Select the appropriate
date Enter the appropriate
time
Click OK
DFL-260 Quick Installation Guide
Autres manuels pour DFL-260 - NetDefend - Security Appliance
1
Table des matières
Autres manuels D-Link Routeur réseau
D-Link
D-Link DES-1005F Manuel utilisateur
D-Link
D-Link DES-3326 Manuel utilisateur
D-Link
D-Link DI-1750 Manuel utilisateur
D-Link
D-Link DXS-1210-12TC Manuel utilisateur
D-Link
D-Link DIR-619L Mode d’emploi
D-Link
D-Link DIR-505 Manuel utilisateur
D-Link
D-Link DES-3624 - Switch - Stackable Manuel utilisateur
D-Link
D-Link DSL-224 Manuel utilisateur
D-Link
D-Link DRO-250i Manuel utilisateur
D-Link
D-Link DSL-2730B Instructions d'installation
D-Link
D-Link DSL-504T Manuel utilisateur
D-Link
D-Link DI-604UP Manuel utilisateur
D-Link
D-Link DWR-980 Manuel utilisateur
D-Link
D-Link DIR-601 Manuel utilisateur
D-Link
D-Link PowerLine DHP-P601AV Manuel utilisateur
D-Link
D-Link DIR Series Manuel utilisateur
D-Link
D-Link DRO-210i Manuel utilisateur
D-Link
D-Link DIR-652 Manuel utilisateur
D-Link
D-Link DSL-502T Manuel utilisateur
D-Link
D-Link DSL-2640R Manuel utilisateur
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité