D-Link DCS-2132L Manuel utilisateur

2440 Camino Ramon, Suite 125

San Ramon, CA 94583

Tel: (800)836-0199 Fax: (925)270-1894

Configure D-Link DCS-2132L Wireless IP Camera for

Cloud Recording, Remote Monitoring and Playback

Contents

Introduction .............................................................................................................................................. 2

Step 1: Connect Camera to the Network and Find Its IP Address ............................................................ 2

1.1 Connect Camera to the Network .................................................................................................... 2

1.2 Find the Camera’s IP Address ......................................................................................................... 3

Step 2: Access the Web-based Camera Configuration Tool ..................................................................... 6

Step 3. Configure Video/Audio or Image Profile Settings......................................................................... 8

Step 4. Configure Motion Detection Settings ........................................................................................... 9

Step 5. Configure the Events (i.e. FTP Server, Media Type and Event) ..................................................10

5.1 Configure the FTP Server Info .......................................................................................................10

5.2 Configure the Media Type (Image snapshots or video clips)........................................................ 12

5.3 Configure an Event........................................................................................................................ 14

6. CameraFTP Viewer..............................................................................................................................15

Introduction

D-Link DCS 2132L is a very popular 1 MP (1280x800 Pixel) H.264 Wireless IP Camera with night-

vision of up to 15 feet and excellent video / image quality. It supports both image snapshot and

video/audio recording. You can use H.264 encoded MP4 video format for best compatibility with video

viewers. WPS is available for easy connecting to Wi-Fi.

Basic camera information

Video / image resolution

1280x800,1280x720,800x600,800x450,

640x480,640x360,320x240;320x180

Audio recording

Supported (2-way)

Image upload frequency

1 image/s

Video frame rate

1, 4, 7, 15, 30 fps

Night-vision

Up to 15 feet

Image snapshot recording

Supported, but only supports 1 image/s. (Continuous recording is

not fully supported.)

Video clip recording

Supported. (Continuous recording is not fully supported)

Motion detection

Supported for both image and video recording

Continuous recording

Continuous recording is not fully supported. It can record 1

minute video/2 minutes, or 10 images/minute.

Supported video format

.MP4

Connection type

Wi-Fi and Ethernet cable; supports WPS

PoE (Power on Ethernet)

Indoor / outdoor

Indoor

Lowest pricing (as of

7/31/2015)

$129.99

Note: This document is not designed to replace the manufacturers’ product manual. The

information provided is based on our knowledge of the model D-Link DCS 2132L.It may not be

accurate or completely up-to-date. Users shall contact the manufacturer for all camera-related

issues and contact us only for CameraFTP-related (i.e. Cloud Service / FTP) issues. Most of the

setup steps below are camera related and are very trivial. If you have finished these basic steps

before, then you can skip Steps 1 and 2. CameraFTP’s service can be configured in just 3 steps

(i.e. Steps 3, 4 and 5).

Step 1: Connect Camera to the Network and Find Its IP Address

1.1 Connect Camera to the Network

There are two ways to connect the IP camera to the Wi-Fi network.

(1) If your Wi-Fi router does not support WPS, then you need to connect the camera using an

Ethernet cable first. You can configure the Wi-Fi settings in the camera's configuration pages

later.

(2) If your Wi-Fi access point/router supports WPS, then it is very easy to connect your device to

the network:

Turn on the camera, then press the WPS button on your Wi-Fi access point for 3 seconds; the

WPS button will usually start flashing. Quickly press the WPS button on the back side of

your camera and hold for a few seconds until the light changes. In about 1 minute, you will

see the status light (below the camera lens) changes to solid green, indicating it is connected

to the wireless router.

1.2 Find the Camera’s IP Address

Please refer to the manufacturer’s manual for more detailed information.

If your camera is connected to the Wi-Fi router, or if you have connected the camera with an

Ethernet cable, then you can run the manufacturer’s setup program to find the camera’s IP

address. From a PC in the same network, insert the camera’s software CD and run the auto-run

program - it will open the following window:

Click "Setup Your Camera" and follow the instructions. Select Next until it starts searching the

network for the camera. After it finishes, you will see this screen:

Note the default password is blank. After you selected the camera, it will ask you to create and

confirm a password. After you entered the password, clicking Next will bring you to setup your

network connection:

Follow the wizard to connect the camera to your network, and click Next. You will be offered to

remotely. You can sign up for an account, or select "I don't want to sign up now".

CameraFTP’s service is different from mydlink service. We offer cloud-based storage for your

camera, which is much more secure than local storage or no storage. Also, we support cloud-

based live view and playback, so mydlink service is not necessary.

Click Next.

Finally, you will find a page that displays the camera's IP address:

Step 2: Access the Web-based Camera Configuration Tool

Once you have found the camera's IP address, launch a web browser and enter the address of

your camera.

http://IP_ADDRESS/

It will pop up a logon dialog as follows:

Use the username: admin and the password you created in the Installation Wizard. If you did not

create a password, the default password is blank (It is recommended that you change the

password). After logging in, you will see the Live Video screen.

Once you are in your configuration pages, click Setup, and you will see the Setup Main screen:

With CameraFTP’s service, most regular setup steps are not required. (You can feel free to check

these steps, e.g. click "Time and Date" to set the camera time.)

Step 3. Configure Video/Audio or Image Profile Settings

Click Setup Audio and Video as shown below. You can configure the video and image

resolution; in the case of video, you can also configure the video frame rate and bit rate. You

only need to configure the Video Profile 1.

If you ordered an image plan, then all it matters is the frame size. This model camera cannot

specify upload frequency for image-based recording. It will always use 1 image/s, so make sure

this is what you ordered on CameraFTP.

If you ordered a video plan, please configure it as follows:

Mode: H.264;

Frame size: Based on your CameraFTP subscription level;

View Window Area: Same as Frame Size;

Max frame rate: Based on your subscription level. Set to 4 if subscription fps is 5.

Video quality: Set to constant bit rate. The number should be calculated as follows:

The Bit Rate is a little tricky. Setting it too high will use too much upload bandwidth, causing

failed uploads; setting it too low will affect the video quality. You can use our bandwidth

calculator to estimate the bandwidth. Visit www.cameraftp.com, click Pricing, and then

customize a service plan. See the screenshot below. (Note for estimating the bandwidth, Number

of Cameras should be set to 1.)

For the video plan of 1280x720, 5 frames/s, the estimated bandwidth is 486Kbps. So you can set

it to 512Kbps.

Click Save Settings (not to be confused with another Save button) to save the video profile.

Step 4. Configure Motion Detection Settings

If you ordered a plan with Motion Detection enabled, then you must configure Motion Detection.

Click Motion Detection as shown below. Check the "Enable Video Motion" checkbox. You can

draw a motion detection area and click Save Settings.

Motion detection is strongly recommended as it can lower your cost and dramatically reduce

bandwidth/storage usage. Moreover, motion detection makes it easier to play back the recorded

footage.

NOTE:

-This camera does not fully support continuous recording. It can only record a 1-minute video

clip every 2 minutes, or 10 images per minute.

-If you use your camera to monitor a busy scene such that the camera will be uploading for

longer than 10 hours/day, you should order the continuous recording plan even if you will

turn on motion detection. Otherwise, your camera may exceed the usage limit and be blocked.

Step 5. Configure the Events (i.e. FTP Server, Media Type and Event)

5.1 Configure the FTP Server Info

If you don’t have an account on CameraFTP, please visit www.cameraftp.com and sign up for a

free trial account. CameraFTP offers a 3-day free trial, after which time you will need to order a

subscription

Assuming you have an account on CameraFTP, click Event Setup, then click the Add button in

the Server section as shown below.

Autres manuels pour DCS-2132L

Table des matières

Autres manuels D-Link Caméra IP

D-Link

D-Link SECURICAM NETWORK DCS-5300 Manuel utilisateur

D-Link

D-Link SECURICAM Network DCS-2120 Manuel utilisateur

D-Link

D-Link Cloud Camera 2330L Manuel utilisateur

D-Link

D-Link DCS-825L Manuel utilisateur

D-Link

D-Link WIRELESS G DCS-950G Manuel utilisateur

D-Link

D-Link SECURICAM Network DCS-2100 Manuel utilisateur

D-Link

D-Link DCS-5020L Manuel utilisateur

D-Link

D-Link DCS-5030L Manuel utilisateur

D-Link

D-Link DCS-2330L Manuel utilisateur

D-Link

D-Link SECURICAM Network DCS-6620 Manuel utilisateur

D-Link

D-Link DCS?6010L Manuel utilisateur

D-Link

D-Link DCS-5000L Manuel utilisateur

D-Link

D-Link DCS-2310L Manuel utilisateur

D-Link

D-Link Air DCS-1000W Manuel utilisateur

D-Link

D-Link DCS-1000 Manuel utilisateur

D-Link

D-Link Securicam Network DCS-2000 Manuel utilisateur

D-Link

D-Link DCS-3420 Manuel utilisateur

D-Link

D-Link SECURICAM Network DCS-3220G Manuel utilisateur

D-Link

D-Link DCS-942L Guide d'installation

D-Link

D-Link DCS-942L Manuel

D-Link

D-Link DCS-3420 Manuel utilisateur

D-Link

D-Link WIRELESS G DCS-950G Manuel utilisateur

D-Link

D-Link SECURICAM Network DCS-2120 Manuel utilisateur

D-Link

D-Link DCS-5020L Manuel

Manuels Caméra IP populaires d'autres marques

FLIR

FLIR Exx series Manuel utilisateur

Avigilon

Avigilon H4A-BO1-IR Manuel utilisateur

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuel utilisateur

ShareTech

ShareTech AV1 Manuel utilisateur

Ezviz

Ezviz C6C Manuel utilisateur

Melchioni

Melchioni UCAM 2015 Manuel utilisateur

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuel utilisateur

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuel utilisateur

Mitel

Mitel 6800i Series Manuel de service

Vitek

Vitek VTC-IR403-212NP Manuel utilisateur

THOMSON

THOMSON DSC - 323W Manuel utilisateur

AVer

AVer FB2027 Manuel utilisateur

ENFORCER

ENFORCER EV-T5105-N2SQ Manuel utilisateur

Wansview

Wansview NC543 Manuel utilisateur

Eneo

Eneo MCB-64A0003M0A Manuel utilisateur

deView electronics

deView electronics CBDNI36F Manuel utilisateur

Swann

Swann SwannEye Manuel utilisateur

LevelOne

LevelOne IP CamSecure Manuel utilisateur