Cypress WirelessUSB N:1 DVK Manuel utilisateur

WirelessUSB™ N:1 DVK

Quick Start Guide

2. Node Board Components

The following diagram identifies the main components of each Node Board. The Hub Node Board and Sensor

Node Board are physically identical. They contain different firmware programs, and the Hub can be identified by

a “Hub” label placed on the board.

1. After selecting the COM port, the software will automatically attempt to initiate communication with the Hub.

a. If the communication is successful, the Connect button will change to Connected.

2. If the sensors are properly configured and powered, then they should appear in the Sensor Status Table.

a. The status of all of the inputs for each sensor board are shown in the status table

b. Note: The Hub and Sensors are configured to automatically establish a network out of the box

without user intervention. After the network has been established, swapping radios between node

boards will cause the Sensor to be unbound (not part of the network). To get the Sensor back on

the network, an Auto Bind or Seeded Bind will need to be performed. Please refer to the N:1 DVK

User’s Guide for more information.

3. Graphing of the potentiometer will also be initiated automatically.

a. Try rotating the potentiometer on any of the 4 sensors boards to observe the resulting graph

b. The potentiometer voltage is only updated during the periodic report interval, or sooner, if the user

initiates an asynchronous event by pressing the User Button or by activating the Magnetic Reed

Switch.

4. Try activating the Red LED on a Sensor Node Board

a. Click on the desired sensor ID in the status table to highlight the row

b. Then click the Red LED checkbox in the Sensor Properties area of the window

c. Then click the Send Command button

d. The Red LED for the selected sensor will illuminate the next time that the sensor communicates

with the Hub

5. For debugging purposes, the serial communication between the PC Host and the Hub are shown in the

message logging window

5. Software Operation

4 3

Potentiometer

DIP Switch

User Expansion Header

WirelessUSB

Radio Header

Power Jumpers

Reset Button

User Button (“S1 BTN”)

ISSP Header

LEDs Cypress PSoC™ Microcontroller

Serial RAM

Thermistor

Magnetic Reed Switch

UART Header

The Hub board is

identified by a label

Sensor Node Boards (4)

10-pin Serial Ribbon Cables (2)

Hub Node Board

Set of three AAA batteries (4)

Serial Adapter Boards (2)

Serial Cables (2)

Radio Modules (5)

Proto Board

24-pin Expansion Ribbon Cable

5V DC Power Adapter

Magnet

CD-ROM

USB

Power

Cable

USB Serial

Adapter

1. Kit Contents

4. Software Installation and Configuration

1. Insert the WirelessUSB N:1 DVK CD-ROM into your PC’s CD drive and launch the CD installer:

• D:\Install WirelessUSB N-to-1 DVK.exe

2. Follow the on-screen instructions to complete the CD installation.

3. Launch the “WirelessUSB N-to-1” software application from the desktop shortcut created by the installer.

• The application can also be found directly on the CD at D:\Software\Nto1\Nto1\Release\Nto1.exe

3. Press the Reset button on each Sensor Node Board.

4. The Green LED (D1) will flash every time the PSoC

wakes up to transmit a packet.

a. By default, each sensor will periodically

transmit a packet once every 5 seconds.

5. There are two ways to initiate an asynchronous packet

transfer

a. Pressing the User Button will initiate a sensor

report

b. Passing the magnet within ¾” of the Magnetic

Reed Switch will also initiate a sensor report.

3B. Sensor Setup

4. Go to the File menu and select Preferences ->

Serial Port

5. Select the desired COM port from the pull-down

menu, select 115200 Baud, and click OK.

1. Ensure the Power Jumpers for the 4

Sensor Node Boards are in the following

positions:

Sensor:

J7: position 2-3

J8: position 2-3

2. Power up the 4 Sensor

Node Boards by

installing the AAA

batteries into the battery

holders on the back of

each sensor

3. Hardware Assembly

3A. Hub Setup

1. Ensure the Power Jumpers for the Hub Node

Board are in the following positions:

Hub:

J7: position 1-2

J8: position 1-2

1. Install a WirelessUSB Radio Module into

each of the 5 Node Boards

2. For default operation, make sure the DIP

switches are all off

2. Connect the 10-pin Serial Ribbon Cable from J1 of the Serial Adapter Board to J1 of the

Hub Node Board observing pin1 polarity.

3. Connect the Serial Cable between P1 of the Serial Adapter Board and a free PC COM port.

4. Power up the Hub Node Board by plugging the 5V DC Power Adapter into J4 of the Serial

Adapter Board and into an available power outlet.

5. Press the Reset button on the Hub Node Board.

6. The Green LED (D1) should now be flashing, indicating that the Hub is operational.

2 5

Autres manuels Cypress Microcontrôleur

Cypress

Cypress CY8CKIT-001 Manuel utilisateur

Cypress

Cypress CY3652 Manuel utilisateur

Cypress

Cypress S29XS128R Manuel utilisateur

Cypress

Cypress CY3664-EXT Manuel utilisateur

Cypress

Cypress CY3280-BSM Manuel utilisateur

Cypress

Cypress CY3660 enCoRe V Manuel utilisateur

Cypress

Cypress CY8CKIT-042-BLE-A Manuel utilisateur

Cypress

Cypress EZ-PD CY4502 Manuel utilisateur

Cypress

Cypress Perform PSOC 5LP PROTOTYPING KIT Manuel utilisateur

Cypress

Cypress S6J3200 Series Mode d'emploi

Cypress

Cypress PSOC 3 FIRSTTOUCH STARTER KIT Manuel utilisateur

Cypress

Cypress CYALKIT-E03 Manuel

Cypress

Cypress CY8CKIT-044 Manuel utilisateur

Cypress

Cypress CY8CKIT-042-BLE-A Manuel utilisateur

Cypress

Cypress CY3250-PLC20QFN Manuel utilisateur

Cypress

Cypress PSoC 5 FIRSTTOUCH CY8CKIT-014 Manuel utilisateur

Cypress

Cypress Traveo S6J3310 Series Manuel utilisateur

Cypress

Cypress EZ-PD CY4502 Manuel utilisateur

Cypress

Cypress CY3274 Manuel utilisateur

Cypress

Cypress CY8CKIT-062-BLE Manuel utilisateur

Cypress

Cypress PSoC CY8CPROTO-062-4343W Manuel utilisateur

Cypress

Cypress CapSense Plus CY3280-CPM1 Manuel utilisateur

Cypress

Cypress FM3 Series Manuel utilisateur

Cypress

Cypress Traveo II Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur

Silicon Laboratories

Silicon Laboratories C8051F800 Manuel utilisateur