CTA PAD-MFSV Manuel utilisateur

Medical Floor Stand

with VESA Tablet Security Holder

PAD-MFSV

INSTRUCTION - MANUAL

CONTENTS:

INSTALLATION:

888-733-4448

2. Attaching Enclosure to VESA

2A. Place hex nut (E) on the front side of the holder VESA in the hex hole. Then,

align holder holes (L) to VESA plate holes (A). Rotate in screws(G) from behind

until securely tightened.

M5 x 14

M5 x 8

M5 Allen Key

Stack of 4 Piece

Foam Adapters

1A. Align base (A) to body as shown. From below, rotate in (A) screw using

provided tool (I) until securely tightened.

1. Setting up Base to Body

**Lift or push down

lever to lock or

unlock wheels

DM5 x 14

M5 Allen Key

M4 Allen key

M4 Nut

M4 x 10

3. Setting up Tray

3A. Using the small mount component (J), insert from the base (as shown

above). Using your fingers, slide until preferred height.

3B. Align tray (C) to mount component (J),then

rotate in screw (F) in from front as shown using

provided allen key (I) until securely tightened.

JJA

M5 x 8

M5 Allen Key

M4 Nut

888-733-4448

6. Setting up Cable Management / Cable Routing

6C. Fish the cable

through the entire body

& out the bottom. Route

through the opening in

the base &plug to

power surge as shown.

7. Setting up Holder & Device

**Power surge for

illustration and

NOT INCLUDED.

Adjusting Height

Rotate knob counterclock-

wise to loosen, and slide

up or down body neck to

desired height. Rotate

knob opposite direction to

securely tighten.

Adjusting Angles and Orientation

Tilt up/down for preferred angles as needed. Rotate left and

right for preferred orientation.

**Tablet shown for

illustration and

NOT INCLUDED.

6A. Insert rubber component (N) into the

side of the holder facing your device’s

charging port. Place cable as shown.

6B. Fish the wire in the back towards the cable clips to help hold the cable in place

and carefully route it from clip to clip until out the side or bottom as preferred.

(Shown above in both images)

7B. Insert key to unlock holder,

then make sure the lever is in

the ‘unlocked’ mode position.

Only then can you adjust holder

arms.

7C. Extend arms outward. Insert device in the center. Retract arms around

the perimeter of device until securely tightened. Place the lever in lock

mode, and click down on the press lock button to lock holder in place.

7A. Stick on the appropriate

foam back so that your tablet

can fit into the holder securely.

You can also stack different

foam pieces for a better fit as

needed.

View from Side of Stacking Foams

Foam

Backing

4. Setting up Basket

4A. Identify the metal plate around the center of the body. Align holes to

the basket holes (B) as shown and rotate in screws (F) using provided

tool (I) until securely tightened.

5. Setting up Power Surge (Not Included)

in the Allocated Brackets

5A. Using provided tool (I), loosen brackets a bit but not too loose that they fall. Slide in

power surge as shown. Push the bracket in towards the body, until tightly fitted against

power surge. Next, tighten screws from side with tool (I) until securely tightened.

**Power surge for

illustration and

NOT INCLUDED.

M5 x 8

M5 Allen Key

Autres manuels CTA Support et étagère

CTA

CTA PAD-FTSU Manuel utilisateur

CTA

CTA PAD-PARAPOSW Manuel utilisateur

CTA

CTA PAD-SCGS Manuel utilisateur

CTA

CTA ADD-PARAFS Manuel utilisateur

CTA

CTA ADD-PARAFSV Manuel utilisateur

CTA

CTA PAD-PF1ICC Manuel utilisateur

CTA

CTA PAD-CHAIRPB Manuel utilisateur

CTA

CTA ADD-PARAFS Manuel utilisateur

CTA

CTA PAD-2VDMWA Manuel utilisateur

CTA

CTA PAD-VPOS1W Manuel utilisateur

CTA

CTA ADD-ADMA Manuel utilisateur

CTA

CTA PAD-ADMA Manuel utilisateur

CTA

CTA PAD-PARAFP Manuel utilisateur

CTA

CTA PAD-PARAF1GT Manuel utilisateur

CTA

CTA PAD-ASK13B Manuel utilisateur

CTA

CTA PAD-HSKSB Manuel utilisateur

CTA

CTA PAD-CHKB Manuel utilisateur

CTA

CTA PAD-KMS Manuel utilisateur

CTA

CTA PAD-PARAFPE Manuel utilisateur

CTA

CTA PAD-SSMANS Manuel utilisateur

CTA

CTA PAD-ASKM6 Manuel utilisateur

CTA

CTA PAD-UAM Manuel utilisateur

CTA

CTA PAD-SWM Manuel utilisateur

CTA

CTA PAD-SSMA Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur