Cross Technologies 2415 0925 Series Manuel utilisateur

Instruction Manual Model 2415-x0925

Multi Channel Upconverter

2415-40925 Four Channel • 2415-30925 Three Channel • 2415-20925 Two Channel • 2415-100925 One Channel

August 2023, Rev. 0

EXECUTE

MODEL 2415

CROSS TECHNOLOGIES INC.

UPCONVERTER

REMOTE

POWER

ALARMS

1674.125 1926.250

1926.375 2086.625

------ CH 1 -------- ------ CH 2 --------

------ CH 3 -------- ------ CH 4 --------

(Shown, Model 2415-40925 - Four Channel, Front Panel)

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment model number,

equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

INSTRUCTION MANUAL

Model 2415-x0925 Multi Channel Upconverter

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Specifications 4

1.3 Monitor & Control Interface 6

1.4 Environmental Use Information 10

2.0 Installation 11

2.1 Mechanical 11

2.2 Rear Panel Inputs & Outputs 12

2.3 Front Panel Controls & Indicators 13

2.4 Operation 14

2.5 Menu Settings 17

3.0 Ethernet Interface 18

3.1 Connection 18

3.2 Ethernet Configuration 18

3.3 Webpage M&C 21

3.4 SNMP Configuration 22

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s

option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall

not be liable for any special, indirect, or consequential damages. This warranty does not

cover parts or equipment which have been subject to misuse, negligence, or accident by the

customer during use. All shipping costs for warranty repairs will be prepaid by the

customer. There are not other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

WEB www.crosstechnologies.com

E-MAIL [email protected]

2415-x0925 Manual, Rev. E Page 2 08/09/23

Model 2415-x0925

Multi Channel Upconverter

2415-40925 Four Channel • 2415-30925 Three Channel • 2415-20925 Two Channel • 2415-100925 One Channel

1.0 General

1.1 Equipment Description

The 2415-40925 Upconverter has four individual channels, each one converts 70 MHz to 950 to 2500 MHz in

125 kHz steps using PLL in “exact frequency mode” with low group delay and flat frequency response.

Synthesized local oscillators (LO) provide frequency selection. Push button switches select the output

frequency, gain, and other parameters. Front panel LEDs provide indication of DC power, PLL alarm or

Remote operation. Gain is adjustable manually over a 0 to +30 dB range in 0.5 ± 0.5 dB steps. The frequency

and gain of each channel are also remotely selectable. Parameter selection and frequency and gain settings

appear on the LCD display. Connectors are Type F female for the RF, and BNC female for the IF and!external

10 MHz reference input and output. The!10 MHz reference can be inserted on all RF lines. The table below

shows available options.!SSPB +24 VDC option V1, can be inserted only on the channel 1 RF line.!The unit is

* 2415-40925, Four (4) Channels, 2415-30925, Three (3) Channels, 2415-20925, Two (2) Channels, 2415-10925, One (1) Channel.

EXECUTE

MODEL 2415

CROSS TECHNOLOGIES INC.

UPCONVERTER

REMOTE

POWER

ALARMS

1674.125 1926.250

1926.375 2086.625

------ CH 1 -------- ------ CH 2 --------

------ CH 3 -------- ------ CH 4 --------

FRONT PANEL (2415-40925 - Four Channel show)

PSA

GND

J11

J12

AND

MONITOR

CONTROL

CHANNEL 4

RF OUT

J10

IF IN

CHANNEL 3

RF OUT

IF IN

CHANNEL 1

RF OUT

VDC

IF IN

10 MHZ REF

OUTPUT

10 MHZ IN/OUT

10 MHZ REF

INPUT

CHANNEL 2

RF OUT

IF IN

PSB

REAR PANEL (2415-40925 - Four Channel shown with optional Ethernet)

FIGURE 1.1 Model 2415-x0925 Front and Rear Panels

SW,PLL,ATT,

10M CONTROL

M&C

CONTROLLER

EXT

10MHz

INT 10MHz

10MHz

VCOs

2415-

40925

Block

Diagram

0.8 to 2.5 HP/LP

2800 MHz BP

3.75 to

5.30 GHz

var

atten

MHz

2870

MHz

200 MHz LP

0.95

2.50

GHz

OUT

SAME FOR FREQUENCY CHANNEL 2

SAME FOR FREQUENCY CHANNEL 3

SAME FOR FREQUENCY CHANNEL 4

10 MHz, std.,

DC - Opt V1

var

atten

------ CH 1 -------- ------ CH 2 --------

------ CH 3 -------- ------ CH 4 --------

1674.125 1926.250

1926.375 2086.625

FIGURE 1.2 Model 2415-x0925 Upconverter Block Diagram

(Block Diagram applies to Models 2415-10925, 20925, 30925 & 40925)

2415-x0925 Manual, Rev. E Page 3 08/09/23

Intermodulation

<-50 dBc for two carriers at Fc +/- 2 MHz spacing, each at -5 dBm out,

(set to -30 dBm input, 30 dB gain)

<-60 dB typical, <-50 dB min.; G=30, -30 dBm input level

Channel to Channel Isolation

-35 to -10 dBm

Input Level Range

Input Characteristics

Output Characteristics

Channel Characteristics

Synthesizer Characteristics

-20 to 0 dBm

Output Level Range

TABLE 1.0 2415-x0925 Multi-Channel Upconverter Technical Specifications**

125 kHz (as low as 1 kHz steps available)

Frequency Step

±1.0 ppm max. over temp. (±0.01ppm, Option H)

Frequency Accuracy

Non-inverting

Frequency Sense

0.015 ns/MHz2parabolic; 0.05 ns/MHz linear; 1 ns ripple

Group Delay, max.

< -50 dBc, in band; <-45dBc out of band (0.2-0.94 GHz and 2.51-3.0 GHz)

Spurious Response

±2.0 dB, 950 - 2500 MHz; ±0.5 dB, 36 MHz BW; ±1.0 dB, 40 MHz BW

Frequency Response

0 to +30.0 dB in 0.5 ±0.5 dB steps

Gain Range (adjustable)

+10 dBm, maximum gain

Output 1 dB compression

950 to 2500 MHz

Frequency

50Ω/ 12 dB (See Table 2.2 for connector options)

Impedance/Return Loss

70 ±18 MHz

Frequency

75Ω/18 dB (See Table 2.2 for connector options)

Impedance/Return Loss

-90 -110

-80

-75

-65

-60

Standard 125 kHz steps dBc/Hz

100k 1M

10k

100

Phase Noise @ Freq (Hz) >

19 inch, 1RU standard chassis, 1.75” high x 16.0” deep

Size

Controls, Indicators

Other

75ΩBNC (female), 75ΩBNC (female) works with 50Ω& 75Ω

IF, 10 MHz Connectors

Direct readout LCD; manual or remote selection

Gain Selection

3 dBm, ± 3 dB, 75 ohms (Option -E)

10 MHz Level (In or Out)

100-240 ±10% VAC, 47- 63 Hz, 45 watts maximum

Power

RS232/RS485 selectable, Ethernet optional)

Remote

Direct readout LCD; manual or remote selection

Frequency Selection

DB9 (female) - NO or NC contact closure on Alarm

Alarm, Remote Connector

50ΩBNC (female)

RF Connector

Green LED; Red LED; Yellow LED

Power; Alarm; Remote

(Technical Specifications continued on page 5...)

2415-x0925 Manual, Rev. E Page 4 08/09/23

(Technical Specifications continued from page 4...)

350 +/- 20 MHz (+/- 1.0 dB 40 MHz BW)

W350-20-x

140 ±36/70 ±18 MHz Selectable

W140/70-x

Ethernet with Web Browser

W8 -

Redundant Power Supply

R -

High Stability (±0.01 ppm) internal ref.

H -

1 kHz Frequency Step Size

X1002 - x

Ethernet with TCP/IP, Telnet®

W28 -

SSPB DC, CH1(ONLY), +24VDC, 2.5 A

V1 -

Available Options

140 ±36 MHz

W140-x

Ethernet with Web Browser & SNMP

W18 -

See TABLE 2.2

Connectors/Impedance

**+10˚C to +40˚C; Specifications subject to change without notice Cross Technologies, Inc. 2015

2415-x0925 Manual, Rev. E Page 5 08/09/23

1.3 Monitor and Control Interface

A) Remote serial interface

Protocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, and 1 stop bit.

(RS-232C, RS-422, or RS-485)

Female DB-9

PC Com Port

Male DB-9

2415-x0925 M&C Port

M&C Cable Diagram - Cross Technologies Frequency Converters

DTR

DSR

RTS

CTS

Connector: Rear panel, DB-9 female

J10 Pinouts (RS-232C/422/485)

Pin Function

1 Rx-

2 Rx+ (RS-232C)

3 Tx+ (RS-232C)

4Tx-

5GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Open

8 Not Used

9 Alarm Relay: Normally Closed

2415-x0925 Manual, Rev. E Page 6 08/09/23

B) Status Requests

Table 1.1 lists the status requests for the 2415-x0925 and briefly describes them.

*PLEASE NOTE: Status requests of values specific to a channel

must be preceded by a *i where *i is the channel number.

*PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below,

should be used ONLY when RS-485 is selected.

TABLE 1.1 2415-x0925 Status Requests

Command Syntax* Description

Get channel frequency {aa*iSF} Returns {*iSFxxxxxxx} where :

• i = 1, 2, 3 or 4 designating the channel number

• xxxxxxx = frequency in KHz

Get channel gain {aa*iSG} Returns {*iSGxxx} where:

• i = 1, 2, 3 or 4 designating the channel number

• xxx = gain to nearest 1.0 dB (e.g., +14 = 14 dB)

Get mute setting {aa*iSM} Returns {*iSMx} where :

• i = 1, 2, 3, or 4 designating the channel number

• x = 1 for Mute ON (carrier OFF)

• x = 0 for Mute OFF (carrier ON)

Get setting for reference {aa*iSL} Returns {*iSLx} where :

insertion on output • i = 1, 2, 3 or 4 designating the channel number

• x = 0 for non-insertion; 1 for insertion

Get input level {aa*iSI} Returns {*iSIxxx} where :

• i = 1, 2, 3, or 4 designating the channel number

• xxx = input level in dBm

Get reference status {aaSE} Returns {SExy} where :

• x = setting: 0 for internal 10 MHz;

1 for external 10 MHz; 2 for auto detect

• y = currently selected in hardware :

0 for internal 10 MHz; 1 for external 10 MHz

Get reference offset (Option O) {aaSO} Returns {SOxxxxx} where :

• xxxxx = an offset amount between -2000 & +2000

2415-x0925 Manual, Rev. E Page 7 08/09/23

(Status Request continued from page 7...)

TABLE 1.1 2415-x0925 Status Requests Continued

Command Syntax* Description

Get IF Frequency {aa*iSY} Returns {*iSYx} where :

(Option W140/70) • i = 1, 2, 3 or 4...

• x = 0 for 70 MHz IF, 1 for 140 MHz IF

Get IP address {aaSi} Returns {Sixxx.xxx.xxx.xxx} where :

(If Ethernet Option, W8, W18, or W28, enabled)

• xxx.xxx.xxx.xxx = IP address

Get subnet mask {aaSs} Returns {Ssxxx.xxx.xxx.xxx} where :

(If Ethernet Option, W8, W18, or W28, enabled)

• xxx.xxx.xxx.xxx = subnet mask

Get channel base parms {aa*iS1} Returns {*iS1tfffffffgggIIIma} where :

• i = 1, 2, 3 or 4 designating the channel number

• t=channel type: 0 for unused;

1 for upconverter; 2 for downconverter

• fffffff = frequency in KHz

• ggg = gain to nearest 1.0 dB (e.g., +25 = 25 dB)

• III = input level in dBm

• m = mute (0 = mute off, 1 = mute on)

• a = alarm: 0 for alarm off; 1 for alarm on

Get alarm status {aaSA} Returns {SAabcd} where:

• a=channel 1 alarm state (0 for alarm off; 1 for alarm on)

• b=channel 2 alarm state (0 for alarm off; 1 for alarm on)

• c=channel 3 alarm state (0 for alarm off; 1 for alarm on)

• d=channel 4 alarm state (0 for alarm off; 1 for alarm on)

Get product/model info {aaSV} Returns {SV2415-x0925xxxver5.00} where:

• 2415-x0925 = product model

• xxx = list of options, if any

•"ver"=separates model & options from firmware version

• 5.00 = firmware version

2415-x0925 Manual, Rev. E Page 8 08/09/23

Table 1.2 lists the commands for the 2415-x0925 and briefly describes them. After a command is sent the

2415-x0925 sends a return “>” indicating the command has been received and executed.

General Command Format - The general command format is {aaCND...}, where:

{ = start byte

aa = address (RS-485 only)

C = 1 character, either C (command) or S (status)

N = 1 character command or status request

D = 1 character or more of data (depends on command)

} = stop byte

*PLEASE NOTE: Commands specific to a channel must be preceded

by *i where i is the channel number.

*PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below,

should be used ONLY when RS-485 is selected.

Table 1.2 2415-x0925 Commands

Command Syntax* Description

Set Channel Frequency

{aa*iCFxxxxxxx}

where i = :

• 1, 2, 3 or 4 designating the channel number

• xxxxxxx = frequency in KHz

Set Channel Gain {aa*iCGxx} where i = :

• 1, 2, 3 or 4 designating the channel number

• xx = gain to nearest 1.0 dB (e.g., {1CGI5} sets channel 1 gain to 15 dB.)

Set input level {aa*iCIxxx} where i = :

• 1, 2, 3 or 4 designating the channel number

• xxx = input level in dBm,

(e.g., {*1CI-20} sets channel 1 input level to -20 dBm)

Set Channel Mute {aa*iCMx} where i = :

• 1, 2, 3 or 4 designating the channel number

• x = 1 for Mute ON (carrier OFF)

• x = 0 for Mute OFF (carrier ON)

10 MHz reference mode {aaCEx} where x = :

• 0 for internal 10 MHz; 1 for external 10 MHz; 2 for auto detect

Reference insertion on output {aa*iCLx} where :

• i = 1, 2, 3 or 4 designating the channel number

• x = 0 for non-insertion; 1 for insertion

Reference offset/adjust {aaCOxxxxx} where x = :

(Option O) • xxxxx = an offset amount between -2000 & +2000

IF Output Frequency {aa*iCYx} where i = :

(Option W140/70) • 1, 2, 3 or 4 designating the channel number

• x = 0 for 70 MHz IF, 1 for 140 MHz IF

2415-x0925 Manual, Rev. E Page 9 08/09/23

1.4 Environmental Use Information

A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions

located in the user manual furnished by the manufacturer of your equipment rack.

B. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition

does not exist due to uneven weight distribution.

C.Elevated operating ambient temperature - If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack may be greater than room ambient temperature.

Therefore, consideration should be given to Tmra. (Maximum Recommended Ambient Temperature)

D. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow

required for safe operation of the equipment is not compromised. Additional space between units

may be required.

E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of circuits could have on over current protection and supply wiring.

Appropriate consideration of equipment name plate rating should be used, when addressing this concern.

F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connection to the Branch

(use of power strips).

G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.

If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED

prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS

emission problems.

2415-x0925 Manual, Rev. E Page 10 08/09/23

Table des matières

Autres manuels Cross Technologies Convertisseur de média

Cross Technologies

Cross Technologies 1584-29 Manuel utilisateur

Cross Technologies

Cross Technologies 2116-182193 Manuel utilisateur

Cross Technologies

Cross Technologies 2415-x02 Manuel utilisateur

Cross Technologies

Cross Technologies 2117 Manuel utilisateur

Cross Technologies

Cross Technologies 2017-0923 370 Series Manuel utilisateur

Cross Technologies

Cross Technologies 2016-03A Manuel utilisateur

Cross Technologies

Cross Technologies 2116-184 Manuel utilisateur

Cross Technologies

Cross Technologies 2015-24 Manuel utilisateur

Cross Technologies

Cross Technologies 2117-9395 Manuel utilisateur

Cross Technologies

Cross Technologies 3116-22-23 Manuel utilisateur

Cross Technologies

Cross Technologies 2005-02P4 Manuel utilisateur

Cross Technologies

Cross Technologies 4115-300 Manuel utilisateur

Cross Technologies

Cross Technologies 2005-10 Manuel utilisateur

Cross Technologies

Cross Technologies 2116-116 Manuel utilisateur

Cross Technologies

Cross Technologies 2016-12 Manuel utilisateur

Cross Technologies

Cross Technologies 2099-2424 Manuel utilisateur

Cross Technologies

Cross Technologies 2016-25-01 Manuel utilisateur

Cross Technologies

Cross Technologies 3016-1520-1200 Manuel utilisateur

Cross Technologies

Cross Technologies 1584 Manuel utilisateur

Cross Technologies

Cross Technologies 2415-02 Series Manuel utilisateur

Cross Technologies

Cross Technologies 2117-8485 Manuel utilisateur

Cross Technologies

Cross Technologies 2016-8085 Manuel utilisateur

Cross Technologies

Cross Technologies 3116-145-1600 Manuel utilisateur

Cross Technologies

Cross Technologies 4115-41-212 Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur