Cross Technologies 2005-10 Manuel utilisateur
Instruction Manual Model 2005-10
Test Upconverter
April 2009 Rev B
DC
ALARM
CROSS TECHNOLOGIES, INC.
2005 TEST CONVERTER
C
KU
LO
70
140
IF
FREQUENCY
GHz
1MHz
10MHz
100MHz
CROSS TECHNOLOGIES, INC.
DC POWER
RF
IF
GAIN
HI
LOW
J1
J3
J2
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,
but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.
for purposes of operating the equipment.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
INSTRUCTION MANUAL
MODEL 2005-10 Test Upconverter
TABLE OF CONTENTS PAGE
Warranty 2
1.0 General 3
1.1 Equipment Description 3
1.2 Technical Characteristics 4
2.0 Installation 5
2.1 Mechanical 5
2.2 Front Panel Controls/Indicators 5
2.3 Rear Panel Input/Output Signals 5
2.4 Accessing the PC Card 6
2.5 Installation/Operation 6
2.6 Environmental Use Information 7
WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.
All Cross Technologies, Inc. products are warranted against defective materials and
workmanship for a period of one year after shipment to customer. Cross Technologies,
Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s
option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall
not be liable for any special, indirect, or consequential damages. This warranty does not
cover parts or equipment which have been subject to misuse, negligence, or accident by the
customer during use. All shipping costs for warranty repairs will be prepaid by the
customer. There are no other warranties, express or implied, except as stated herein.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
2005-10 Manual, Rev. B Page 2 4/28/09
MODEL 2005-10 Test Upconverter
1.0 General
1.1 Equipment Description
The 2005-10 Test Upconverter converts a 70 MHz or 140 MHz IF signal to 2000 to 2500 MHz in 1 MHz steps
with selection of high side LO (C = inverted) or low side LO (Ku = non-inverted) and 70 or 140 MHz input
over the 2.0 - 2.5 GHz range.
Featuring low phase noise, these units are used to loop 70 or 140 MHz modulators to 2.0 - 2.5 GHz receivers
for test purposes. The 70 or 140 MHz carrier input is mixed with a synthesized local oscillator (LO) signal.
The output frequency is selected with four BCD switches which control the synthesized LO. Front panel
LEDs light when DC power is applied (green) and when a PLL alarm occurs (red). The mixer output is
applied to the output attenuator providing a nominal gain of -10 dB (high gain) or -30 dB (low gain).
Connectors are 50ΩBNC (female) for the IF input and for the RF output (other connector options are
available). Wall power supply options are -P for 120 VAC, 60Hz, and -P4 is 100-240 ±10% VAC.
The 2005 can be mounted on a 1 3/4” X 19 “ rack mount panel (option -R).
2000
to
2500
MHz OUT
70
or
140
MHZ IN
1860
to
2640
MHz
ATTEN
2.
3
3
8
CONTROLLER
FIGURE 1.1 Block Diagram
DC
ALARM
CROSS TECHNOLOGIES, INC.
2005 TEST CONVERTER
C
KU
LO
70
140
IF
FREQUENCY
GHz
1MHz
10MHz
100MHz
CROSS TECHNOLOGIES, INC.
DC POWER
RF
IF
GAIN
HI
LOW
J1
J3
J2
FIGURE 1.2 Front and Rear Panel
2005-10 Manual, Rev. B Page 3 4/28/09
1.2 Technical Characteristics
TABLE 1.0 2005-10 Upconverter Specifications*
Input Characteristics
Impedance 50Ω
Return Loss 15 dB
Frequency 70 or 140 MHz center, ± 20 MHz
Level -10 to -25 dBm (LOW GAIN)
-25 to -40 dBm (HI GAIN)
1dB compression 0 dBm (LOW GAIN)
-15 dBm (HI GAIN)
Output Characteristics
Impedance 50Ω
Return Loss 12 dB
Frequency Range 2.0 to 2.5 GHz
Channel Characteristics
Gain -30 dB ± 3 dB (LOW GAIN)
-10 dB ± 3 dB (HI GAIN)
Spurious Response < -40dBC max, < -45dBC typ; OUTPUT NOT FILTERED
Frequency Response ± 2 dB, 2.0 - 2.5 GHz; ± 0.5 dB, any 10MHz increment
Synthesizer Characteristics
Frequency Accuracy ± 25 kHz max
Frequency Step 1.0 MHz minimum
-100
-90
-75
-70
-70
1MHz
100kHz
10kHz
1kHz
100 Hz
dBC/Hz
Phase Noise @ Freq
Indicators
DC Power Green LED
PLL Alarm Red LED
Other
RF, IF Connectors BNC (female)
Size, Bench Top 4.7” wide X 1.75” high X 6.5” deep
Size, Rack Mount 19 inch standard chassis 1.75”high X 7.0” deep (option -R)
AC Power 120 VAC, 60 Hz, 10W max wall mount power supply (option -P) or
100-240 ±10% VAC, 47-63 H, wall mount power supply (option -P4)
*+10 to +40 degrees C; Specifications subject to change without notice
2005-10 Manual, Rev. B Page 4 4/28/09
2.0 Installation
2.1 Mechanical
The 2005 is packaged in an aluminum extrusion. The -R option is mounted on a 1 3/4” X 19” panel that can
be mounted to a rack using the 4 holes at the ends. The unit derives +DC from the RF out center conductor
(+14 to +24 VDC) or the wall power supply (+15V unregulated, option -P, -P4). See Figure 2.3.
2.1.1 Cleaning Instructions
Wipe the exterior with a dry, soft cloth. Use no detergent or cleaning chemicals.
2.2 Front Panel Controls/Indicators - Figure 2.1 shows front panel controls and indicators for the 2005-10.
SW6 - LO SELECT
Slide switch selects high side (C) or
low side (Ku) local oscillator.
DS1 - POWER LED
Lights green when DC
power is present
SW1 to SW4 - FREQUENCY BCD SWITCHES
Select the desired output frequency which is the LO
frequency - 70, -140, +70, or +140 MHz in GHz.
DS2 - ALARM LED
Lights red when PLL
comes out of lock
SW5 - IF SWITCH
Slide switch selects 70 or 140 MHz IF in.
DC
ALARM
CROSS TECHNOLOGIES, INC.
2005 TEST CONVERTER
C
KU
LO
70
140
IF
FREQUENCY
GHz
1MHz
10MHz
100MHz
FIGURE 2.1 2005-10 Front Panel Controls and Indicators
2.3 Rear Panel Input/Output Signals - Figure 2.2 shows the input and output signals to the 2005-10.
J1 - IF INPUT
70 or 140 MHz input.
-10 dBm max level for
LOW GAIN (-30 dB)
-30 dBm max level for HI
GAIN (-10 dB)
BNC (female) 50Ω
J3 - DC POWER
The unregulated DC voltage from the
wall power supply (option P, P4).
15 VDC, 200 ma.
J2 - RF OUT
The mixed RF output.
This is an UNFILTERED
output and contains
mainly the RF, LO - IF,
LO, LO + IF, mixer
products.
BNC (female) 50Ω.
SW7 - GAIN SWITCH
Slide switch selects -10 dB high
gain (HI) or -30 dB low gain (LOW).
+15
GND
CROSS TECHNOLOGIES, INC.
DC POWER
RF
GAIN
HI
LOW
J1
J3
J2
IF
FIGURE 2.2 2005-10 Rear Panel Inputs and Outputs
2005-10 Manual, Rev. B Page 5 4/28/09
2.4 Accessing the PC Card
There are NO USER JUMPERS or other on-card controls. ALTHOUGH IT IS NOT RECOMMENDED AND
MAY VOID THE WARRANTY the following shows how to remove the printed circuit board (PCB) from the
extrusion:
1. ALWAYS REMOVE POWER when installing or removing the PCB from the extrusion
2. Remove four (4) rear panel screws (see Figure 2.3).
3. GENTLY pull the rear panel and PCB assembly completely out of the extrusion.
4. To install the PCB, GENTLY push the rear panel and PCB assembly completely into the extrusion
Make sure the shield goes in the lower channel and the PCB in the next channel above that in the
extrusion and that the front panel controls go through the front panel holes.
5. Install four (4) rear panel screws.
EXTRUSION
FRONT SCREWS (4EA)
FRONT PANEL
RACK MOUNT PANEL (FOR -R MODELS ONLY)
REAR SCREWS (4EA)
PCB
ASSEMBLY
REAR PANEL
WALL
POWER
SUPPLY
(-P and -P4 ONLY)
2005 TEST CONVERTER
CROSS TECHNOLOGIES, INC.
DC
100MHz
FREQUENCY
10MHz
1MHz
GHz
LO
IF
C
KU
70
140
ALARM
FIGURE 2.3 2005 Assembly Drawing
2.5 Installation / Operation
2.5.1 Installing and Operating the 2005-10
1. If using the receiver LNB voltage to power the 2005-10, be sure +14 to +24 VDC is on the RF
center conductor. If using the wall power supply (options -P or -P4), connect the power supply to
the DC POWER connector and either 120 VAC (-P) or 100-240 ±10% VAC (-P4) (Figure 2.2)
2. Select either C or KU band (SW6) and either 70 or 140 MHz IF (SW5) using the front panel
switches (Figure 2.1).
3. Select either HI or LOW GAIN using the switch (SW7) on the rear panel (Figure 2.2).
4. Connect a -10dBm max (LOW GAIN) or -25 dBm max (HI GAIN) signal to IF In, J1 (Figure 2.2).
5. Connect the RF OUT, J2, to the receiver under test (Figure 2.2).
6. Set BCD switches, SW1 to SW4, to the desired frequency (Figure 2.1).
7. Be sure DS1 (green, DC Power) is on and DS2 (red, Alarm) is off (Figure 2.1).
2005-10 Manual, Rev. B Page 6 4/28/09
2.6 Environmental Use Information
A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions
located in the user manual furnished by the manufacturer of your eqipment rack.
B. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition
does not exist due to uneven weight distribution.
C.Elevated operating ambient temperature - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack may be greater than room ambient temperature.
Therefore, consideration should be given to Tmra.
D. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised. Additional space between unit
may be required.
E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply
circuit and the effect that overloading of circuits could have on over current protection and supply wiring.
Appropriate consideration of equipment name plate rating should be used, when addressing this concern.
F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connection to the Branch
(use of power strips).
G. Top Cover - There are no servicable parts inside the product so, the Top Cover should not be removed.
If the Top Cover is removed the ground strap and associated screw MUST BE RE-INSTALLED
prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS
emission problems.
2005-10 Manual, Rev. B Page 7 4/28/09
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
2005-10 Manual, Rev. B Page 8 4/28/09
Table des matières
Autres manuels Cross Technologies Convertisseur de média
Cross Technologies
Cross Technologies 2116-300-1600 Manuel utilisateur
Cross Technologies
Cross Technologies 2117-7172 Manuel utilisateur
Cross Technologies
Cross Technologies 2115-275-1845 Manuel utilisateur
Cross Technologies
Cross Technologies 2117-9395 Manuel utilisateur
Cross Technologies
Cross Technologies 2016-03A Manuel utilisateur
Cross Technologies
Cross Technologies 2017-03 Manuel utilisateur
Cross Technologies
Cross Technologies 2005 Manuel utilisateur
Cross Technologies
Cross Technologies 2015-26 Manuel utilisateur
Cross Technologies
Cross Technologies 2016-12 Manuel utilisateur
Cross Technologies
Cross Technologies 2099-2424 Manuel utilisateur
Cross Technologies
Cross Technologies 1584 Manuel utilisateur
Cross Technologies
Cross Technologies 2017-03A Manuel utilisateur
Cross Technologies
Cross Technologies 2116-140T120 Manuel utilisateur
Cross Technologies
Cross Technologies 2415-02 Series Manuel utilisateur
Cross Technologies
Cross Technologies 3016-1520-1200 Manuel utilisateur
Cross Technologies
Cross Technologies 3117-3338 720 Series Manuel utilisateur
Cross Technologies
Cross Technologies 3116-192 Manuel utilisateur
Cross Technologies
Cross Technologies 2415 0925 Series Manuel utilisateur
Cross Technologies
Cross Technologies 2015-05 Manuel utilisateur
Cross Technologies
Cross Technologies 3116-22-23 Manuel utilisateur
