Creative Wireless Headset Manuel utilisateur

English. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Language TOC.fm Page 1 Monday, August 23, 2004 6:43 PM

Language TOC.fm Page 2 Monday, August 23, 2004 6:43 PM

Your Creative Wireless Headset for

Bluetooth at a Glance

Your Creative Wireless Headset for Bluetooth®is supplied with a built-in lithium-ion

battery.

Microphone

Earpiece

Tri-color Light Emitting Diode (LED)

Power adapter

jack

Multi-function

button

Volume

buttons

Wireless Bluetooth headset.fm Page 3 Monday, August 23, 2004 6:40 PM

When your headset is not in use, connect the earpiece to your headset as shown in

Figure 1.

Figure 1

Wireless Bluetooth headset.fm Page 4 Monday, August 23, 2004 6:40 PM

Getting Started

1Charge your headset

Your headset needs to be fully charged before you use it for the first time. To charge your

headset’s battery, connect your headset to the wall outlet as shown in Figure 2.

The Tri-Color LED indicates the battery status. It turns red when the battery is charging,

and green, when the battery finishes charging. Charging your battery fully for the first time

takes approximately three hours.

For more information on your Tri-color LED, see ”Reading your headset’s Tri-color LED”

on page 9.

• A fully charged battery should supply you with approximately up to four hours of talk

time and up to 120 hours of standby time. Talk time, however, may vary depending on

your mobile phone’s settings and usage.

• When the battery is almost depleted, the Tri-color LED blinks red once every four

seconds and your headset beeps once every minute. Recharge the battery at the

earliest opportunity.

• If you are charging your battery for the first time, or have not used your headset in a

while, the Tri-color LED may take slightly longer to turn red.

Figure 2

Wall outlet

Power adapter jack

Power adapter

Tri-color LED

Wireless Bluetooth headset.fm Page 5 Monday, August 23, 2004 6:40 PM

2Pair your headset and mobile phone

Before using your headset for the first time, pair it with a Bluetooth-enabled mobile phone.

If the pairing is not completed within two minutes, the Tri-color LED blinks yellow, and the

headset beeps five times before turning itself off automatically. Should this happen, repeat

steps 2 to 7.

1. If your headset is turned on, turn it off by pressing and holding the Multi-function

button for three seconds. The Tri-color LED turns off and you hear a beep.

2. Place your headset within one meter (three feet) of your mobile phone, as shown in

Figure 3.

3. Press and hold the Multi-function button for eight seconds. The Tri-color LED

alternately blinks red and green.

4. Turn on your mobile phone’s Bluetooth feature. For more information, see your

mobile phone’s User’s Guide.

Figure 3

One meter (three

feet) or less

Wireless Bluetooth headset.fm Page 6 Monday, August 23, 2004 6:40 PM

5. Set your mobile phone to detect Bluetooth devices.

6. From the list that appears, select Creative Headset.

7. When prompted for a passkey, press 0000 on your mobile phone and select OK.

When the pairing is completed, the Tri-color LED blinks green rapidly five times and

you hear a long beep.

8. Select Return to go back to your mobile phone’s main menu. A headset icon may

appear on your mobile phone’s screen.

You can now start to make and receive calls from your headset.

3Make a call

Before making a call, make sure that your headset is paired with your mobile phone. For

pairing instructions, see ”Pair your headset and mobile phone” on page 6.

1. Turn on your headset by pressing and holding the Multi-function button for two

seconds. The Tri-color LED blinks green and you hear a beep.

2. Dial a number using your mobile phone.

3. When connected, talk using your headset’s microphone.

4. To end the call, press the Multi-function button once. You can also end a call using

your mobile phone.

For more usage information, see section “Using Your Headset“.

• When no calls are in progress and your mobile phone is turned on, your headset

goes into standby mode.

• When using your headset with your mobile phone, make sure that it is within 10

meters (30 feet) of your mobile phone.

Wireless Bluetooth headset.fm Page 7 Monday, August 23, 2004 6:40 PM

Using Your Headset

Your headset has a Multi-function button, located on the earpiece, which allows you to

turn on or off your headset. With the Multi-function button, you can answer or end calls,

and use the Last Number Redial* feature, without using your mobile phone.

The table below shows you how to use the buttons on your headset.

*Some features are available only for selected mobile phones. For more information, refer to your mobile

phone’s User’s Guide.

Usage Action

Turning on your

headset Press and hold the Multi-function button for two seconds. The

Tri-color LED blinks green and you hear a beep.

Turning off your

headset Press and hold the Multi-function button for three seconds. The

Tri-color LED turns off and you hear a beep.

Going into pairing

mode After your headset is turned off, press and hold the Multi-function

button for eight seconds. The Tri-color LED alternately blinks red and

green.

Answering a call Press the Multi-function button. You can also answer the call using

your mobile phone.

Ending a call Press the Multi-function button to end a call. You can also end a call

using your mobile phone.

Using Voice Dial* Press the Multi-function button and when you hear a beep, say the

voice tag.

Using Last Number

Redial* Press the Multi-function button twice.

Adjusting volume Press any one of the Volume buttons to gradually increase the

volume. Once the volume reaches the maximum level, it starts again

from the minimum.

Wireless Bluetooth headset.fm Page 8 Monday, August 23, 2004 6:40 PM

Reading your headset’s Tri-color LED

Your headset’s Tri-color LED indicates the mode your headset is in. The table below shows

you the various Tri-color LED indications available.

Tri-color LED Meaning

Red On Your headset’s battery is charging.

Blinks once every

four seconds Your headset’s battery is almost depleted.

Recharge the battery at the earliest opportunity.

Green

On Your headset is fully charged.

Blinks rapidly every

two seconds Your headset is being turned on.

Blinks rapidly five

times in successsion Your headset has been successfully paired to

your mobile phone.

Blinks once every

four seconds Your headset is in standby mode.

Blinksonceevery15

seconds A call is in progress.

Yellow

Blinks once every

four seconds

Your headset is in standby mode and is not

paired with your mobile phone.

Your headset automatically turns off after three

minutes.

Blinks rapidly five

times in successsion Your headset has failed to pair with your mobile

phone and will automatically turn off.

Green and red Blinksalternatelyfor

two minutes Your headset is in pairing mode and is ready for

pairing.

Wireless Bluetooth headset.fm Page 9 Monday, August 23, 2004 6:40 PM

Table des matières

Autres manuels Creative casque

Creative

Creative SOUND BLASTER WORLD OF WARCRAFT HEADSET - Manuel utilisateur

Creative

Creative SOUND BLASTER WORLD OF WARCRAFT HEADSET - Guide de référence

Creative

Creative Sound Blaster Jam Manuel utilisateur

Creative

Creative HS-720 V2 Manuel utilisateur

Creative

Creative SB1770 Manuel utilisateur

Creative

Creative SOUND BLASTER WORLD OF WARCRAFT HEADSET - Manuel utilisateur

Creative

Creative SoundBlaster Tactic 3D Rage GH0220A... Manuel utilisateur

Creative

Creative SXFI AIR GAMER Manuel utilisateur

Creative

Creative HEADSET HS-1200 Manuel utilisateur

Creative

Creative Aurvana Live!2 Manuel utilisateur

Creative

Creative Sound BlasterX H6 Manuel utilisateur

Creative

Creative SOUND BLASTER TACTIC3D OMEGA WIRELESS Manuel utilisateur

Creative

Creative Hitz WP380 Manuel utilisateur

Creative

Creative Outlier One Manuel utilisateur

Creative

Creative WP-450 Manuel utilisateur

Creative

Creative EF0970 Manuel utilisateur

Creative

Creative Sound Blaster EVO Mode d’emploi

Creative

Creative Sound Blaster EVO Manuel utilisateur

Creative

Creative WP-250 Manuel utilisateur

Creative

Creative HS-220 Manuel utilisateur

Creative

Creative Sound Blaster EVO Manuel utilisateur

Creative

Creative CB2460 Manuel utilisateur

Creative

Creative SOUND BLASTER TACTIC3D OMEGA WIRELESS Manuel utilisateur

Creative

Creative SoundBlaster Tactic 3D Rage GH0220A... Guide de démarrage rapide

Manuels casque populaires d'autres marques

Sena

Sena SMH10 Manuel utilisateur

IASUS

IASUS Stealth IA-NT4-BASIC-BT Manuel utilisateur

Sennheiser

Sennheiser EPOS ADAPT 230 Manuel utilisateur

Doro

Doro Flexus HS2005 Manuel utilisateur

GE 98971 Manuel utilisateur

Hama

Hama 00184070 Manuel utilisateur

Plantronics

Plantronics Blackwire 3200 Series Manuel utilisateur

Blue Tiger

Blue Tiger Advantage PLUS Manuel utilisateur

Jawbone

Jawbone Icon Manuel utilisateur

Jabra

Jabra FR 20 Manuel utilisateur

Roxcore

Roxcore Flow A+ Manuel utilisateur

Turtle Beach

Turtle Beach XP 510 Manuel utilisateur

Philips

Philips SHB6101 Manuel utilisateur

Jabra

Jabra PRO 9460 Duo Manuel utilisateur

HyperX

HyperX HyperX Cloud Flight Manuel utilisateur

Bose

Bose MIE2 Mobile Manuel utilisateur

Jabra

Jabra Steel Manuel utilisateur

HyperX

HyperX cloud ii Manuel utilisateur