Creative Blaster Modem Manuel utilisateur

Sound Blaster Wireless Headphones

User’s Guide

Congratulations!

Your Sound Blaster®Wireless Headphones works with Sound Blaster

Wireless transmitters like Sound Blaster X-Fi™ Notebook and Sound

Blaster Wireless for iTunes®. Together, your transmitter and headphones

enable you to enjoy your favorite music, wherever you are in your home,

wirelessly. For a list of supported devices, visit www.soundblaster.com.

About Your Headphones

USB

OFF ON

1Powerswitch/LED

2 Audio Line In jack

3 USB connector

(for charging only)

4 Connect button / Link

LED

5 Previous / Rewind

button *

Press and hold to rewind.

6 Next / Fast Forward

button *

Press and hold to fast forward.

7 Play / Pause button *

8 Volume buttons

* Function is available with the transmitter software installed and applicable to these

media players: iTunes®, Windows®Media Player and Creative Music Server.

Getting Started 2

Getting Started

Step 1: Charge your headphones

For first use, charge the headphones for at least 12 hours. Turn off the

headphones while charging. The Power LED lights up red when charging,

and turns off when fully charged.

Step 2: Enable your transmitter

Ensure that your Sound Blaster Wireless transmitter (available separately)

is turned on and its wireless control is enabled. Refer to your transmitter’s

user documentation to do this.

IMPORTANT Use only the charger supplied with your headphones.

12 hrs

OFF ON

1 USB connector

2DC-to-USBcable

3 Power adapter

4 Power outlet

Turn on headphones and Auto pair 3

Step 3: Turn on headphones and Auto pair

Turn on your headphones. If you have two or more headphones, simply turn

on all of them. Your transmitter and headphones should pair automatically.

The Link LED flashes and then lights up green when pairing is successful.

NOTE • If your transmitter and heaphones do not pair, simply reset

them. On one unit at a time, press and hold the Connect button

for five seconds. The LED flashes twice to indicate that the

headphones has been reset.

• Signal quality between the transmitter and headphones may be

affected by any object or structure (for example, multiple walls)

that is between the units. Experiment with different positions if

necessary.

USB

OFF ON

Play and stream music 4

Step 4: Play and stream music

Once paired, you can use your headphones up to 30 meters away from your

transmitter. Play music from your transmitter to check that the headphones

is receiving the music wirelessly.

Wearing the headphones

Adjust the headband so that the headphones

rests lightly on your head. Do not tighten

excessively.

CAUTION Adjust headphones volume to a comfortable level. Do not listen to

audio on your headphones at high volumes for prolonged periods

of time as hearing loss might result.

<30 metres

About Broadcasting and Zone Control 5

About Broadcasting and Zone Control

Control your headphones remotely from your transmitter, using the

Broadcast and Zone Control buttons found on your transmitter’s software.

For more information on using these features, refer to your transmitter’s

documentation.

Broadcasting

Use Broadcast mode to stream music to all your

receivers* simultaneously. This mode can be

used with or without manual pairing and enables

you to quickly set up and use your wireless music

system - perfect for occasions such as parties

when you want everyone to listen to the same

music throughout your home.

Zone Control

Use Zone control if you wish to stream the same

song to selected receivers* only. This mode

requires you to do manual pairing. If your

transmitter is capable of transmitting multiple^

playback streams, you can stream different

songs to different receivers.

NOTE * Refers to the Sound Blaster Wireless Headphones, as well as other

supported Sound Blaster Wireless receivers and speakers.

^ For news and updates on the availability of our multi-stream

transmitter, the Sound Blaster Wireless MultiPlay, as well as other

Sound Blaster Wireless devices, visit www.soundblaster.com.

R R

Transmitter

Receiver

Manual Pairing 6

Manual Pairing

This section shows you how to pair your transmitter and headphones

manually.

Step 1: Press the Connect button on your transmitter

Press the Connect button on your transmitter’s hardware or software. The

transmitter’s Link LED flashes.

TIP For more effective pairing, bring the headphones close to the

transmitter when pairing the devices. Once paired, you can use the

headphones at another location in the house.

NOTE Your transmitter may differ in appearance from the one shown

here.

CONNECT

Press the Connect button on your first headphones 7

Step 2: Press the Connect button on your first headphones

This must be done within three minutes after pressing the Connect button

on the transmitter (Step 1). Once the transmitter and headphones are

paired successfully, the Link LED on both units light up green and remain

on. The first receiver to be paired will be assigned to Zone 1.

Perform the following steps to pair additional headphones:

Step 3: Press the Connect button on your transmitter

again

The transmitter’s Link LED flashes.

Step 4: Press the Connect button on your second head-

phones

Once the transmitter and the second headphones are paired successfully,

the Link LEDs on both units light up green and remain on. Repeat the steps

to pair your third and fourth headphones (if applicable) manually.

NOTE If your transmitter and heaphones do not pair, simply reset them.

On one unit at a time, press and hold the Connect button for five

seconds.

USB

Using Your Headphones 8

Using Your Headphones

Adjusting volume

Press the Volume Up or Down buttons on your headphones.

Charging your headphones

After initial charging, your headphones take approximately three (3) hours

to be fully charged using the supplied charger. You can continue to use the

headphones while it is charging.

Using Wireless Off mode

Your headphones can be used as normal wired heaphones. When you

connect an external audio source to the Audio Line In jack, the headphones’

wireless features will be disabled.

USB

1 Audio Line In jack

2Audiocable

(available separately)

3 CD player, MP3 player

or other external audio

sources.

4LinkLED

Turns off when an external

source is connected to the

Audio Line In jack.

Using Your Headphones 9

Understanding the Power LED

Understanding the Link LED

Power switch Charger

connected

LED color & behavior Status

ON No / Yes Blue - Stable Turned on and ready for use

No Blue - Flashing

(beep every min)

Battery low

No Red - Flashing On standby mode

(turned off remotely by

transmitter)

No Not lit Battery flat /

Audio Line In detected

OFF No Not lit Turned off

Yes Not lit Fully charged

Yes Red - Stable Charging

LED Behavior Status

Green Stable Paired (Turned on)

Flashing Pairing in progress

Not lit – Connection lost /

Wireless Off mode

OFF ON

●

❊

❍

OFF ON

❍

●

❊

Autres manuels pour Blaster Modem

Table des matières

Autres manuels Creative Casque audio

Creative

Creative SENSEMORE AIR EF1020 Manuel utilisateur

Creative

Creative WP-450 Manuel de service

Creative

Creative Outlier One Manuel utilisateur

Creative

Creative SXFI Theater Manuel utilisateur

Creative

Creative GH0280 EVO ZX Manuel utilisateur

Creative

Creative Sound Blaster Jam V2 Manuel utilisateur

Creative

Creative Outlier Black EF0770 Manuel utilisateur

Creative

Creative SXFI Theater Manuel utilisateur

Creative

Creative Outlier Pro Manuel utilisateur

Creative

Creative WP-250 Manuel utilisateur

Creative

Creative SXFI Theater Manuel utilisateur

Creative

Creative TACTIC 3D WRATH Manuel utilisateur

Creative

Creative WP-300 Manuel utilisateur

Creative

Creative EF0840 Manuel utilisateur

Creative

Creative ZEN Manuel utilisateur

Creative

Creative AURVANA IN-EAR 2 - Manuel utilisateur

Creative

Creative HQ-2300D Guide de dépannage

Creative

Creative AURVANA Gold Manuel utilisateur

Creative

Creative SOUND BLASTER TACTIC3D OMEGA WIRELESS Manuel utilisateur

Creative

Creative SENSEMORE AIR Manuel utilisateur

Creative

Creative Super X-Fi SXFI AIR Manuel utilisateur

Creative

Creative Aurvana X-Fi Manuel utilisateur

Creative

Creative HS-930I Manuel utilisateur

Creative

Creative Sound Blaster EVO Zx Mode d’emploi

Manuels Casque audio populaires d'autres marques

Sony

Sony MDR-NC8 Manuel utilisateur

AUSounds

AUSounds AU-Stream Manuel utilisateur

ENERGY SISTEM

ENERGY SISTEM Style 7 Manuel utilisateur

Philips

Philips SHE3622 Manuel utilisateur

Insignia

Insignia NS-CAHBTSPORT Manuel utilisateur

Movie Vision

Movie Vision HP-400 Manuel utilisateur

MobiFren

MobiFren SM Pro Manuel utilisateur

Motorola solutions

Motorola solutions PMLN8120 Manuel utilisateur

Jaybird

Jaybird freedom Guide d'installation

Sony

Sony MDR-ED12LP Manuel utilisateur

HiFuture

HiFuture Tidy Buds Pro Manuel utilisateur

Renkforce

Renkforce RF FTVK-100 Manuel utilisateur

Philips

Philips SHQ3000 Manuel utilisateur

Sennheiser

Sennheiser 500371 Manuel utilisateur

Califone

Califone 2924AV Manuel utilisateur

Philips

Philips EARGEAR HE205 Series Manuel utilisateur

Technics

Technics EAH-AZ80 Manuel utilisateur

Bose

Bose On-Ear Headphone Manuel d'utilisation et d'entretien