Crane DN5800 Instructions d'utilisation et d'installation

M132.4 Page 1of 3June 25, 2019

SERVICE INFORMATION

104883 (M132.4)

MODELS AFFECTED: All BevMax 4/3/2 Classic Model Venders.

MODEL NUMBERS: DN5800/3800 – BevMax 4/3/2 Venders

Revised: 6/25/19

RE: Crane Merchandising Systems DN5800/3800-4/3/2 Validator Guard Assembly.

Reason: To provide installation instructions when installing the Validator Guard Assembly. If you have

any issues please contact your Crane Merchandising Systems Representative or the Technical Service

Department at 803-266-5001.

Order: 1 – 111250 (previous # 65701440) BevMax 4/3/2 Validator Guard Kit

Kit Contents:

1 – 104705 (previous # CR0013381) Assembly, Validator Guard BevMax 4/3/2

5 – 100267 (previous # 80030423) Screws, Phil Pan Sems #8-18X1/2”

1 – 104883 M132.x Installation Instructions

Figure 1

Note access hole for the

screw to the vertical

lamp assy.

M132.4 Page 2of 3June 25, 2019

SERVICE INFORMATION

Installation:

1. Unplug the vender.

2. A. If the Validator Guard 104705 (previous # CR0013381) Assembly did not arrive assembled,

assemble the parts as shown in Figure1. Do not tighten the Hex Nuts at this time.

B. If the Validator Guard Assembly arrived assembled, be sure the two Hex Nuts are not tight at

this time.

3. Orient the Validator Guard Assembly as shown in Figure 1.

4. Position the Validator Guard Assembly in position in the Vender Service Area so the left flange

points upward and the bottom of the plate rests just above the top edge of the Discharge Frame.

Figure 2

5. Check no wires are pinched, cut, or damaged in any way.

Figure 3

Note positioning of the

access hole for the

screw to the vertical

lamp assy.

M132.4 Page 3of 3June 25, 2019

SERVICE INFORMATION

6. Ensure the left & right front edges of the Validator Guard Assembly are even with the front edges

of the cabinet. See Figures 2 & 3.

7. Secure the Validator Guard Assembly in position with 5 Phil Pan Sems self-drilling Screws 100267

(previous # 80030423).

8. Tighten the 2 Hex Nuts on the Validator Guard Assembly. See Figure 4.

Figure 4

9. Close Service Door and confirm there is no interference with any parts on the Service Door or in

the Service Area of the Vender.

Figure 5

10. Plug in vender and test for proper operation.

Hex Nut

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Crane marchandiseur

Crane

Crane BevMax 4 Manuel utilisateur

Crane

Crane Coca-Cola BevMAX Refresh Mode d'emploi

Crane

Crane 787E Manuel

Crane

Crane BevMAX Refresh 6 Media Manuel utilisateur

Crane

Crane Dixie Narco Glassfront BevMax 3 Manuel utilisateur

Crane

Crane BevMax 3 Instructions d'utilisation et d'installation

Crane

Crane BEVMAX 6 Manuel utilisateur

Crane

Crane Snack Center 1 Manuel utilisateur

Manuels marchandiseur populaires d'autres marques

FRIGOGLASS

FRIGOGLASS Flex 20 HC Manuel utilisateur

Hussmann

Hussmann ENTYCE TY3 Manuel utilisateur

EPTA

EPTA COSTAN RHINO MULTI Manuel utilisateur

Hussmann

Hussmann CRFD Mode d'emploi

CASCO

CASCO Nano Cube Manuel utilisateur

Hussmann

Hussmann WDCHI Manuel utilisateur

True

True GDIM-26 Manuel utilisateur

Structural Concepts

Structural Concepts Oasis Mobile Series Instructions d'installation

Hussmann

Hussmann Q2-SS Instructions d'utilisation d'origine

Haussmann

Haussmann RL Manuel utilisateur

Howard McCray

Howard McCray R-CDS32E-4 Manuel utilisateur

Hussmann

Hussmann microSC SHM-A Series Manuel utilisateur

Hussmann

Hussmann APT0500 Manuel utilisateur

EPTA

EPTA iarp Cool Emotions Delight Lite Manuel utilisateur

VALERA

VALERA BC 85 Manuel utilisateur

HL Display

HL Display 3eBin Manuel utilisateur

Hussmann

Hussmann Q1-SS Mode d’emploi

Hussmann

Hussmann impact Excel C2X-XLEP Mode d’emploi