Crane Dominator 80mm Series Manuel

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS

Z9801P

Z9801PF

These instructions cover the

general notes for the following

Z9801P & Z9801PF 80mm

Series units;

•Flow management system for fan coil

units.

•Combines essential control components

and connecting pipework into one

compact, fully assembled unit ready

to connect.

•The 80mm Dominator Peak Pro is

compact and ultra lightweight.

•The bypass valve unit comprises two 3

Way Ball valves.

•Includes the Peak Pro (Pressure

Independent Control Valve) for

optimum flow control.

•The strainer unit has an integral filter and

pressure test point, plus drain cock/vent

facility.

SYSTEM COMPONENTS

For detailed installation, operating and maintenance instructions for the system components

that combine to make up the Z9801P/Z9801PF Series Dominator Peak Pro, please see the

relevant sections of our website as below:

CFS_Z9801_0219

??????_v?

CRANE HOUSE, EPSILON TERRACE,

WEST ROAD, IPSWICH,

SUFFOLK IP3 9FJ

TELEPHONE: +44 (0)1473 277300

FAX: +44 (0)1473 277301

EMAIL: [email protected]

www.cranefs.com

Every effort has been made to ensure that the information contained in

this publication is accurate at the time of publishing. Crane Ltd assumes

no responsibility or liability for typographical errors or omissions or

for any misinterpretation of the information within the publication and

reserves the right to change without notice.

• Designed and manufactured under quality management

systems in accordance with BS EN ISO 9001:2008

FM311 ISO 9001

For information on all other components and additional configurations please contact the

Crane Technical Support Desk at: [email protected]

www.cranebsu.com

80mm SERIES

Z9801P

Z9801PF

D995 PEAK PRO PICV D901/D902 METERING STATION

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS

CRANE FLUID SYSTEMS DOMINATOR PEAK PRO 80MM SERIESCRANE FLUID SYSTEMS DOMINATOR PEAK PRO 80MM SERIES

INSTALLATION

The valve may be installed directly or remotely to a load (typically a Fan Coil Unit).

The direction of flow should be such that the PICV is on the return from the load.

Temperature Range: -10 to 120*C | Pressure rating: PN16

MODES OF OPERATION

PREPARATION/FITTING

Steel tube: Cut square and de-burr internally and externally, thread to BS EN 10226-2 and fit

to Dominator using PTFE tape to BS7786:2006 or other recommended jointing compound.

Other types of piping system can be used providing a suitable adaptor with a threaded

end is utilised.

Whilst fitting pipe and/or adaptors it is important that the wrench is positioned close to

the joint to be assembled, in order to avoid damaging the valve.

The Dominator Peak Pro shall be supported using proprietary mounting brackets or other

suitable devices. This enables the pipework to be well supported and avoids undue strain on the

joints of the Dominator Peak Pro.

OPERATION: BYPASS VALVE

The mode of operation has four primary modes of operation. it is factory set in Isolation /

Flushing bypass mode. The mode of operation can be changed by operation of the ‘T@ balls as

indicated in Figure 2.

ORIENTATION & HANDING

The Dominator has two unions fitted to allow for orientation and handing of the PICV, Strainer

and Bypass valve.

MAINTENANCE

This valve is intended for group 2 liquids only, as defined by the pressure Equipment Directive

2014/68/EU.

For further assistance please call our technical helpline on +44 (0) 1473 277400 or email us at:

[email protected]

Following a policy of continuous improvement, Crane Fluid Systems reserves the right to alter

specifications shown in this document and the e-catalogue without prior notice.

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONSINSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS

ISOLATION AND FLUSHING BYPASS BACK FLUSHING

NORMAL OPERATION FORWARD FLUSHING

Ce manuel convient aux modèles suivants

Autres manuels Crane Unité de contrôle

Crane

Crane NOZ-CHEK Cryogenic Manuel

Crane

Crane Dominator PRO Z4000 Series Instructions de montage

Crane

Crane Duo-Chek Manuel utilisateur

Crane

Crane KROMBACH 510 Manuel

Crane

Crane CPV36M Series Manuel utilisateur

Crane

Crane D923 Manuel utilisateur

Crane

Crane D2003 Instructions de montage

Crane

Crane CRYOFLO T-Globe Manuel utilisateur

Crane

Crane Class 150 Manuel utilisateur

Crane

Crane DM921 Instructions d'utilisation

Crane

Crane D1088 Manuel

Crane

Crane D1088 Manuel utilisateur

Crane

Crane KROMBACH TUFSEAT Performance Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur