Craftsman 917.372490 Manuel utilisateur

MODEL 917.372490 OWNER'SMANUAL

*Assembly

*Operation

*Maintenance

*Service

*Adjustments

*Repair Parts

Caution:

Readand Foffew

aJJSafety Rules

arid instructions

Before Operating

ThisEquipment

RULES

CAUTION: _L_AYSI_DiS_NN!ECT SPARK PLUG WiRE AND PLACE WiRE

WHERE IT CANNOT CONTACT S_ARK PLUG TO PREVENT ACCIDENTAL STAR_ ,_

TING WHEN SETTING-UP, TRANSPORTING, ADJUSTING OR MAKING

REPAIRSTOYOURLAWNMOWER

IMPORTANT

FEDERAL REGULATIONS REQUIRE OPERATOR PRESENCE BLADE STOP CONTROLS TO MINIMIZE THE

RISK OF BLADE CONTACT INJURY. YOUR LAWN MOWER IS EQUIPPED WITH SUCH CONTROLS. DO

NOT ATTEMPT TO DEFEAT THE FUNCTION OF THE OPERATOR PRESENCE CONTROL UNDER ANY

CIRCUMSTANCES.

• BE CAREFUL-WHEN THE ENGINE IS RUN-

NING THE BLADE iS TURNING.

• Please read your owner's manual. Only allow

raerSons who know the safety rules to use your

wn mower.

•DO NOT tie the operator presence control bar

to the handle. Control must be free to permit

brake engagement when handles and control

are released.

•DO NOT allow children to use your lawn

mower.

•0r before each use°

Tic etc.

•stones, wires, cans, boards,

etc. from area to be mowed. These objects can

be thrown by the blade.

° DO NOT allow children, bystanders or pets in

the area while mowing.

•Always wear shoes when mowing. DO NOT

operate lawn mower when barefoot or wear-

ing open sandals.

•Always wear safety glasses or eye shields

before starting your lawn mower and while

mowing.

Always shut off engine before trying to adjust

wheelheights.

When engine is running, DO NOT put hands

or feet under lawn mower or in the discharge

chute, nor make any adjustments.

Stay clear of discharge opening at all times.

• Do not fill gas tank when engine is running,

when indoors or when engine is hot. Allow

engine to cool for several minutes before fill-

ing gas tank. Clean off any spilled gasoline

before starting engine.

Mow only in good light.

• Always stop blade when not cutting grass or

when crossing gravel drive, sidewalk, or

roadway.

• DO NOT continue to run your lawn mower if

you hit a foreign object. Stop the engine,

disconnect the spark plug wire from the spark

plug, inspect the lawn mower for damage and

make repairs as required°

DO NOT use a damaged lawn mower. Always

have damage repaired before mowing.

• DO NOT run your lawn mower if it vibrates

too much. Stop engine and make repairs.

Vibration is an indication of damage.

•Never use your lawn mower without proper

guards or deflectors in place.

• Always mow across a slope or inclined area.

DO NOT mow up or down a slope or inclined

area.

•DO NOT mow in wet grass. Be careful of

footing when mowing in wet grass, use shoes

with good traction.

•DO NOT run with the lawn mower.

• DO NOT run your lawn mower indoors. Exo

haust gases are deadly poison.

•Always disconnect the spark plug wire from

spark plug to prevent accidental starting when

transporting or storing your lawn mower after

the mowing season.

• DO NOT attempt to raise engine speed above

factory settings. Engine damage or personal

injury may result.

• If a grass catcher is used on your lawn mower,

check the catcher often for damage or

deterioration, it will wear through normal use.

Use only a recommended replacement catcher.

•Always stop blade to remove or install catcher.

•DO NOT store your lawn mower or gasoline

where fumes may reach an open flame and

cause a fire.

•DRAIN THE GASOLINE from your lawn

mower before transporJ'i_ng your lawn mower

inside your car or othe_J_ve_ideo

LOOKFORTHISSYMBOLTOPOINT OUT IMPOR-

,_ TANTSAFETYPRECAUTIONS.IT MEANS-- ATTEN-

TION!I! BECOME ALERT!!! YOUR SAFETY IS

INVOLVED.

CONG TU TWONSonyaurpurchaseofa PRODUCTSPECiFiCATiONS

smart Lawn Mower° h has been designed,

engineered and manufactured to give you the bes_ .......

possible dependability and performance.

Should you experience any problem you cannot easi-

ly remedy, please contact your nearest Sears Ser-

vice Center/Department. We have competent, well-

trained technicians and the proper tools to service

or repair this unit.

Please read and retain this manual. The instructions

will enable you to assemble and maintain your lawn

mower properly. Always observe the "SAFETY

RULES".

MODEL

NUMBER 917.372490

SERIAL

NUMBER

DATE OF

PURCHASE

THE MODEL AND SERIAL NUMBERS WiLL BE

FOUND ON A DECAL ATTACHED TO THE REAR

OF THE LAWN MOWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER

AND DATE OF PURCHASE AND KEEP iN A SAFE

PLACE FOR FUTURE REFERENCE_

HORSE POWER: 5.0

DISPLACEMENT: 12.04 cu. in.

GASOUNE CAPACITY: 1.5 quart

(Unleaded)

OIL (21 oz. Capacity}: SAE 30 or

(SAEI0W30)

SPARK PLUG (GAP _030 in.): Champion

RJ 19-LM or

Sears 77 33312

or STD 361458

VALVE CLEARANCE: intake: .008 in.

Exhaust: _008 in.

SOLID STATE IGNITION

AiR GAP: .0125 in.

BLADE BOLT TORQUE: 35-40 ft.dbs.

MAmNTENANCEAGREEMENT

A Sears Maintenance Agreement is available on .fhis producL Contact your nearest Sears store for details_

CUSTOMERRESPONSIBILITIE$

• Read and observe the safety rules.

Fallow a regular schedule in maintaining, caring for and using your lawn mower.

Foltow the instructions under "Maintenance" and "Storage" sections of this Owner's Manual°

TWOYEARLIMITEDWARRANTYON CRAFT. MANPOWERMOWER

For two years from the date of purchase, when this Cra_sman Lawn Mower is maintained, Jubricated and tuned-

up according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in material

and workmanship.

if this Craftsman Lawn Mower is used for commercial or renta! purposes, this warranty applies for only 90

days from the date of purchase.

This warranty does not cover:

Expendable items which become worn during normal use, such as rotary mower blades, blade adapters,

belts, air cleaners and spark plug.

Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to

maintain the equipment according to the instruct'ons conta°ned °n the owner's manual

WARRANTY SERVICE iS AVAILABLE BY RETURNING THE CRAFTSMAN POWER MOWER TO THE

NEAREST SEARS SERVICE CENTER/DEPARTMENT iN THE UNITED STATES_ THIS WARRANTY APPLIES

ONLY WHILE THiS PRODUCT IS IN USE IN THE UNITED STATES.

This warranty gives you specific legal rights, and you may a_so have other rights which may vary from state

to state.

Sears_. Roebuck and Company, D/731CRoW, Sears Tower, Chicago, IL 60684

TABLEOFCONTENTS

SAFETYRULES................................................ 2

PRODUCTSPECIFICATIONS............................. 3

CUSTOMERRESPONSIBIUTIES......................... 3

WARRANTY.................................................... 3

LAWN MOWER ACCESSORIES........................ 5

ASSEMBLY...................................................... 6

OPERATION .............................................. 7-10

MAINTENANCE ....................................... 11-13

SERVICE AND ADJUSTMENTS ................... 14-25

STORAGE ..................................................... 16

SERVICE RECOMMENDATIONS ...................... 17

TROUBLESHOOTING ..................................... 18

REPAIR PARTS - LAWN MOWER ............... 20-24

REPAIR PARTS - ENGINE .......................... 25-27

PARTS ORDERING/SERVICE .......... BACK COVER

INDEX

Accessories............................................ 5

Adjustments:

Carburetor.................................. 14

HandleHeight............................. I 5

HeightofCut................................. 8

Air Filter:.

Replacement............................... 13

Assembly:

Handle ......................................... 6

GrassCatcher............................... 6

Blade:

Sharpening................................. 11

Replacement............................... 11

Controls:

EngineZoneControlCable............ 9

OperatorPresenceControlBar ......7

CustomerResponsibilities..................... 3

Engine:

Oil Cap......................................... 7

Oil Change................................. 12

Oil Level....................................... 9

oil Type........................................9

Starting....................................... 10

Storage....................................... 16

Fuel:

Type............................................. 9

Storage....................................... T6

Handle:

Adiustment................................. |5

Assembly...................................... 6

Bracket....................................... 16

Knob ............................................ 7

Lubrication:

Engine........................................ |7

BrakeSpringBrackets................. 17

HandleBracketMountingPins..... 17

RearDoorHinge......................... !7

WheelAdjusters.......................... 17

Maintenance................................. 14-!7'

Agreement.................................... 3

Air Filter..................................... 13

BladeCare/Replacement............. ! 1

Engine........................................ 1:2

GearCase.................................. 12

GrassCatcher............................. 12

Lubrication.................................. 17

SparkPlugs................................ 13

MowingTips...................................... 10

Oil: Engine.......................................... 9

Storage....................................... 16

Operation:

OperatingLawnMower ...........7-10

OperatorPresenceControlBar .............7

Options:

Attachments.................................. 5

Repair/ReplacementParts............. 20-24

Responsibilities,Customer.................... 3

SafetyRules......................................... 2

Serviceand Adjustments:

Carburetor.................................. 14

Handle ....................................... 15

ServiceRecommendations.................. 17

SparkPlugs....................................... !3

Specifications.................................. '... 3

Startingthe Engine:

StarterHandle............................. 10

StoppingtheEngine........................... 10

Storage.............................................. 16

TroubleShootingChart....................... 18

Warranty............................................. 3

Wheels:

WheelAdiusters............................ 8

These accessories were available when this lawn mower was produced. They are also available at most Sears

retail outlets, catalog and service centers. Most Sears stores can order repair parts for you, when you provide

the model number of your lawn mower. Some of these accessories may not apply to your lawn mower.

ENGINE

SPARKPLuG MUFFLER AIR FILTER GASCAN ENGINEOIL STABILIZER

If lawn mower is an electric start

LAWNMOWERPERF!

REARBAG

OPTIONAL

REPLACEMENT

BAGFORREAR

DISCHARGE

LAWNMOWERS

OPTIONAL

CATCHERFOR

SIDEDISCHARGE

LAWNMOWER

_RMANCE

DUSTSHIELD LEAFCATCHER

SIDEDISCHARGECATCHER

BATTERY __

CLIPPING DEFLECTOR

PERMANEXCATCHER

LAWNMOWERMAINTENANCE

WHEELS LAWN MOWER COVER

ASSEMBLY

Your lawn mower has been assembled at the fac-

tory except for the Grass Catcher Bag and the Grass

Catcher Frame.

TOREMOVELAWNMOWERFROMCARTON

* Cut down the corners of the carton and lay ends

and sides down flat.

= Cut the plastic wrapping and remove from over

Handles and lawn mower.

= Remove Catcher Frame, Fabric Bag and Oil Bot-

tle from top of lawn mower.

*Lift lawn mower off of shipping base and check

carton for loose parts.

HOWTOSET-UPYOURLAWNMgWER

TOUNFOLDHANDLE

Remove Handle Padding holding Operator

Presence Controt Bar to Upper Handle.

Raise Handles until Lower Handle section locks

into place in mowing position ISee Fig. 1}.

Raise Upper Handle section into place on Lower

Handb and tighten one i1) Handle Knob.

*Your lawn mower has been shipped with Protec-

tive Handle Pads placed between the upper and

lower sections otthe Handle° For best lawn

mower performance these Pads need to be

discarded after the Handle isplaced in the mow-

ing position.

*Once the Handle is in the mowing position,

remove the Handle Knob, Handle Bolt and Pro-

tective Pad from the side with the loose Handle

Knob. (Make sure the other side is tight to sup-

part the Upper Handle).

*Discard the Pad and reinstall the Handle Bolt and

Knob--Tighten securely.

o Loosen and remove the Handle Knob, Handle

Bolt and Protective Pad from the other side and

discard the Pad.

oReinstall the Handle Bolt and Knob-'Tighten

securely, Now your Handles should be clamped

together without the Protective Pads.

o Your Lawn Mower Handle can be adjusted for

your mowing comfort. Refer to "Adjust Handle"

in the Service and Adjustment Section of this

manual.

TOASSEMBLE& ATI'ACHGRASSCATCHER

• PutGrass Catcher Frame into Grass Bag with stiff

part of Bag on the bottom.

•"Stip vinyl bindings over Frame ISee Fig. 2).

NOTE: If vinyl bindings are too stiff, hold them in

warm water for a few minutes, ff Bag gets wet, let

it dry before using.

OPERATOR £RESENCE

CONTROL BAR

uLIFT UP

LIFT UP /////,'

_,//t

MOWING POSITtON

DOOR

GRASS CATC FRAME

FIG. 3

- Liftthe Rear Door on the Lawn Mower Housing

and place the Grass Catcher Frame onto the form-

ed up Tabs on the Rear Door Hinge Bracket (See

Fig. 3).

• The Grass Catcher is secured to the Lawn Mower

Housing when the Rear Door islowered onto the

Grass Catcher Frame.

- CASH YoueLAWHMOW_e

__ oRA_ROVeD[

_ T.ELAWNMOWERW_HT,_[

OPERATION

KNOWYOURLAWNMOWER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER. Com-

pare the illustrations with your Lawn Mower to familiarize yourself with the location of various controls

and adjustments. Save this manual for future reference.

OPERATOR PRESENCE

CONTROL

ENGINE ZONE

CONTROL

DRIVE CONTROL LEVER

_TARTER HANDLE

CABLE CLIP HANDLE KNOB

;ABLE CLIP

ENGINE OIL CAP

GRASS CATCHER ---4_ _CAP

PRIMER

COVER

AIR FILTER

WHEEL ADJUSTER

(ON EACH WHEEL) HOUSING

FIG. 6

MEETSCPSCSAFETYREQUIREMEHTS

Sears Rotary Walk-Behind Power Lawn Mowers conform to the safety standards of the American National

Standards Institute and the U.S. Consumer Product Safety Commission. The blade turns when the engine

is running.

OPERATOR PRESENCE CONTROL BAR - must be DRIVE CONTROL LEVER - used to engage power-

held down to the handle to start the engine. Release propelled forward motion of lawn mower.

to stop the engine.

PRIMER _pumps additional fuel from the carburetor

to the cylinder for use when starting a cold engine. STARTER HANDLE - used for starting the engine.

DRIVECONTROL

• Self-propelling is controlled by holding the

operator presence control bar down to the han-

dle and pushing the drive control lever forward

until it clicks; then release the lever (See Fig. 7).

o Forward motion will stop when the operator

presence control bar is released. To stop forward

motion without stopping the engine, release the

operator presence control bar slightly until the

drive control disengages. Hold operator presence

controt bar down tohandle to continue mowing

without self-propelling°

To keep drive control engaged when turning cor-

ners, push down on handle and lift front whee&

off ground while turning tawn mower.

_0 EMPTYGR._SSCATCHER

o To remove Grass Catcher, release Operator

Presence Contro! Bar to stop engine°

o Lift up Rear Door and remove the Grass Catcher

by the Handle lSee Fig_ 6).

Lift up Rear Door and remove the Grass Catcher

by the Handle (See Fig. 6).

• Do no_drag the Bag when emptying; itwill cause

unnecessary wear.

TO ADJUSTCUTTINGHEIGHT

*Raise wheels for low cut and lower wheels for

high cut.

*Wheels are set in low cut for shipping. Adiust cut-

ting height to suit your requirements. Medium

position is best for most lawns.

" To change cutting height, squeeze adjuster lever

toward wheel. Move wheel up or down to suit

your requirements. Be sure all wheels are in the

same setting (See Fig. 8).

\ \ OPERI TOR PRESENCE

\ "_COflTROL BAF \

_ ..... . _ _ CONTROL--4_

DRIVE CONTROL DISENGAGED

FIG. 7

\\\

FIG. 8

LOWER WHEELS " RAISE WHEELS

FOR HIGH CUqr -- -_.I"_'_ "-'P'' FOR LOW CUT

FIG. 9

BEFORESTARTINGENGINE

01L: GASOUNEF_LLERCAP

A 20 oz. bottle of Pennzoil SAE 30 Oi! is included

with your new lawn mower.

*Remove engine oil cap with dipstick (See Fig. 10)

and fiJ! to the FULL line on the dipstick.

"Use 20 ozs. of SAE 30 oil. SAE 10W 30 oil can

also be used. DO NOT use SAE lOW 40 oil.

,POUR OIL SLOWLY. DO NOT OVER FILL.

® Check oil level before each use. Add oil if need-

ed. Fill to FULL line on dipstick.

® To read proper level, tighten engine oi! cap each

time.

o Replace engine oil cap with dipstick and tighten.

After the first two (2) hours of mowing, change

the oil, and every 25 hours thereafter. You may

need to change the oil more often under dusty,

dirty conditions.

GAS:

*Fill gasoline tank with fresh, clean unleaded

gasoline. DO NOT USE PREMIUM GASOLINE.

BE CAREFUL NOT TO OVERFILL TANK (SEE

FIG. 10).

WARNING: Experience indicates that alcohol blend-

ed fuels (called gasohol or using ethanol or methanol)

can attract moisture which leads to separation and

formation of acids during storage. Acidic gas can

damage the fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be

emptied before storage for 30 days or longer. Drain

the gas tank, start the engine and let it run until the

fuel lines and carburetor are empty. Use fresh rue)

next season. See Storage Instructions for addifiona_

information.

Never use engine or carburetor cleaner products in

the fuel tank or permanent damage may occur.

ENGINEZONE CONTROL

CAUTaON:FEDERALREGULATIONSREQUIREAN

ENGINECONTROLTO BEINSTALLEDON THIS

LAWN MOWER tN ORDERTO M|NIMIZE THE

ElSE OF BLADECONTACTINJURY. DO NOT

UNDERANY CIRCUMSTANCESATTEMPTTO DE-FEAT. THE FUNCTION OF THE OPERATOR

CONTROL.THEBLADETURNSWHENTHEENGINE

!S RUNNING.

Your lawn mower is equipped with an Operator

Engine Control Bar which requires the operator

to be positioned behind the lawn mower handle

to start and operate the lawn mower.

To start a cold engine, push primer five (5) times

before trying to start. Use a firm push° This step

is not usually necessary when starting an engine

which has already run for a few minutes°

® Hold operator presence control bar down to the

handle and pull starter ha_dle quickly. Do not

o))ow s)arter rape )o snap back.

o To STOP engine_ release operator presence con_

trol bar°

NgT_: in coabr weather it may be necessary to

repeat priming steps° Jnwarmer weather over prim°

ing may cause flooding and engine will not _tart. ff

you do flood engine wait o few minutes before at-

tempting to start and DO NOT repea_ priming steps_

e Under certain conditions, such as very tall grass_

it may be necessary to raise the height of cut to

reduce pushing effort and to keep from

overloading the engine and leaving dumps af

grass clippings.

For extremely heavy cutting, reduce the width of

cut and raise the rear of the lawn mower hous°

ing one I1) wheel adjuster setting higher than the

front for better discharge of grass.

When using a rear discharge lawn mower in

moist, heavy grass, dumps of cut grass may not

enter the grass catcher° Reduce ground speed

tpushing speed) and/or run the lawn mower over

the area a second tirae.

ff a trail of grass clippings is left on the right side

of a rear discharge lawn mower, mow in a

clockwise direction with a small overlap to col-

[oct the clippings on the next pass.

The vent holes in the baffle in back of apermanex

catcher can become filled with dirt and dust with

use and the catcher will collect less grass.

To prevent this, reguJarly hose the catcher baffle

with water and let dry before using_

Table des matières

Autres manuels Craftsman Tondeuse à gazon

Craftsman

Craftsman 247.370340 Manuel utilisateur

Craftsman

Craftsman 944.365530 Manuel utilisateur

Craftsman

Craftsman EZ 917.270810 Manuel utilisateur

Craftsman

Craftsman 917.257621 Manuel utilisateur

Craftsman

Craftsman 944.600191 Manuel utilisateur

Craftsman

Craftsman 917.374802 Manuel utilisateur

Craftsman

Craftsman 917.389490 Manuel utilisateur

Craftsman

Craftsman 917.270742 Manuel utilisateur

Craftsman

Craftsman 917.378450 Manuel utilisateur

Craftsman

Craftsman 917.389382 Manuel utilisateur

Craftsman

Craftsman 944.360040 Manuel utilisateur

Craftsman

Craftsman 944.362080 Manuel utilisateur

Craftsman

Craftsman 944.609150 Manuel utilisateur

Craftsman

Craftsman 917.272245 Manuel utilisateur

Craftsman

Craftsman 28910 - Lt 2000 20 HP 42" Lawn Tractor Manuel utilisateur

Craftsman

Craftsman 917.273280 Manuel utilisateur

Craftsman

Craftsman 917.258680 Manuel utilisateur

Craftsman

Craftsman 917.275762 Manuel utilisateur

Craftsman

Craftsman 37147 Manuel utilisateur

Craftsman

Craftsman 917.270741 Manuel utilisateur

Craftsman

Craftsman 917.377220 Manuel utilisateur

Craftsman

Craftsman 917.273240 Manuel utilisateur

Craftsman

Craftsman 917.373231 Manuel utilisateur

Craftsman

Craftsman 917.37945 Manuel utilisateur

Manuels Tondeuse à gazon populaires d'autres marques

RHINO

RHINO 1958 Manuel utilisateur

Wolf Garten

Wolf Garten Compact plus 40 B Manuel utilisateur

Cub Cadet

Cub Cadet LTX 1045 Manuel utilisateur

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuel utilisateur

Challenge

Challenge CH18V2 Instructions de fonctionnement

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuel utilisateur

DEWEZE

DEWEZE ATM-725 Manuel d'utilisation

Weed Eater

Weed Eater 180083 Manuel utilisateur

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuel utilisateur

Better Outdoor Products

Better Outdoor Products Quick Series Manuel utilisateur

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuel d'utilisation

MTD

MTD 795, 792, 791, 790 Manuel utilisateur

Toro

Toro Groundsmaster 3505-D Manuel utilisateur

Dennis

Dennis FT 610 Manuel utilisateur

AIRFORCE

AIRFORCE F-15 Gen 3 Manuel utilisateur

MTD

MTD 126-220-000 Manuel utilisateur

Toro

Toro 74806 Manuel utilisateur

Stihl

Stihl RMA 443 PV Manuel utilisateur