CORNING LSE 6875-SB Manuel utilisateur

Model Nos.

6875-SB, 6885-DB, 6895-FB

6876-SB, 6886-DB, 6896-FB

6877-SB, 6887-DB, 6897-FB

6878-SB, 6888-DB, 6898-FB

Corning®LSE™

Digital Dry Bath Heater

Instruction Manual

About This Manual

This manual is designed to assist you in the optimal usage of your Corning LSE

Digital Dry Bath Heater. The manual is available in English, French, German, Italian,

Portuguese, and Spanish at www.corning.com/lifesciences.

Corning® LSE™ Digital Dry Bath Heaters – Single-, Dual-, and Four-block models

Instruction Manual

Corning®LSE™Digital Dry Bath Heater

Table of Contents

1.0 General Specifications ........................................... 2

2.0 Safety Precautions ............................................... 2

3.0 Installation ...................................................... 3

4.0 Controls ......................................................... 3

5.0 Operation ....................................................... 4

6.0 Calibration ...................................................... 4

7.0 USB Interface .................................................... 5

8.0 Troubleshooting Guide........................................... 6

9.0 Service and Repair Information ................................... 6

10.0 Cleaning and Maintenance ....................................... 7

11.0 Equipment Disposal – European Regulations ..................... 7

12.0 Appendix: Symbols and Conventions ............................. 7

13.0 Limited Warranty ................................................ 8

Intended Use

Corning LSE Digital Dry Bath Heaters provide comprehensive designs for

a wide variety of life science research applications. Excellent temperature

control figures can deliver accurate and reliable experimental results from

one experiment to another.

If the equipment is used in a manner not specified by the manufacturer,

the protection provided by the equipment may be impaired.

1.0 General Specifications

Temperature range Ambient +5°C to 150°C

Temperature 0.1°C 4 digit LED

display resolution

Temperature ±0.2°C (at 37°C in block)

uniformity

Temperature ±0.3°C

accuracy

Temperature Microprocessor – user calibratable

controller

Timer 1 to 99 hours 59 minutes or continuous in

1 minute increments

Operating altitude Not to exceed 2,000 meters

Control PI Microprocessor controller

I/O USB unidirectional

Dimensions Single and dual block models:

(W x D x H) 8.3 x 12.4 x 4.7 in. (21 x29 x 12 cm)

Four block models:

8.3 x 16.3 x 4.7 in. (21 x 39 x 12 cm)

Weight Single and dual block models:

7.0 lbs. (3.2 kg)

Four block models:

9.6 lbs. (4.4 kg)

Electrical 6875-SB: 115V, 50/60Hz, 1 A, fuse 1.6 AT

requirements 6876-SB: 230V, 50/60Hz, 0.5 A, fuse 1AT

6877-SB: 230V, 50/60Hz, 0.5 A, fuse 1AT (UK plug)

6878-SB: 100V, 50/60Hz, 1 A, fuse 1.6 AT

6885-DB: 115V, 50/60Hz, 1.9A, fuse 3.15AT

6886-DB: 230V, 50/60Hz, 0.95 A, fuse 1.6AT

6887-DB: 230V, 50/60Hz, 0.95 A, fuse 1.6AT (UK plug)

6888-DB: 100V, 50/60Hz, 1.9A, fuse 3.15AT

6895-FB: 115V, 50/60Hz, 3.73 A, fuse 5 AT

6896-FB: 230V, 50/60Hz, 1.86 A, fuse 3.15 AT

6897-FB: 230V, 50/60Hz, 1.86 A, fuse 3.15 (UK plug)

6898-FB: 100V, 50/60Hz, 3.73 A, fuse 5 AT

2.0 Safety Precautions

Do not use this product in an explosive environment.

Do not use in the presence of flammable or combustible material.

Do not heat substances that react violently when heated.

Do not touch block when hot or when unit is heating. Use block lifter.

Do not touch area around block or block well when unit is hot.

Do not spill liquids into the well area or into the unit side vent holes.

Connect unit only to a properly grounded outlet.

Caution: HOT surfaces that can burn or cause injury.

Use of this product in any manner not specified by the manufacturer or

modification of the product may cause injury and/or may void the warranty.

3.0 Installation

Upon unpacking the Corning® LSE™ Digital Dry Bath Heater, inspect for

damage. Shipping damage is the responsibility of the carrier. Inspect that

the following are present: instruction manual, data logger software, line

cord, block lifter, lid, USB cable.

Select a location that is dry and not subject to drafts or moving air from

heating or air conditioning vents or air blown by other equipment. Place

the unit on a flat, preferably non-flammable, surface. Allow sufficient room

around the unit for access and cooling (six inches minimum on all sides is

suggested). Plug the unit into a properly grounded outlet. Using the lifter,

insert the block(s) into the well. The unit is now ready for use.

4.0 Controls

On/Off rocker switch, located on the back of the unit: Turns primary power

on and off.

Start/Stop LED, red: Used to activate or stop the unit. Illuminates when unit

is in heating mode; off in temperature set mode.

Time LED, green: Used to set or select Time mode. This LED light indicates

running Time mode.

Heating LED, red: Illuminates when unit is in Heating mode and unit is

applying heat to the block. This LED is on continuously during heat-up and

cycles on and off when the unit is at the set temperature.

Temperature Up arrow key: Raises set temperature when unit is in Set mode.

Temperature Down arrow key: Lowers set temperature when unit is in Set mode

Timer Up arrow key: Raises set time when unit is in Set mode.

Timer Down arrow key: Lowers set time when unit is in Set mode.

5.0 Operation

1. Place the Corning® LSE™ Digital Dry Bath Heater on a sturdy and level

surface in a safe, dry place away from laboratory traffic.

2. Ensure the AC power switch is Off, then plug the three-pronged power

cord into a grounded three-prong AC outlet of the appropriate voltage

(115V or 220V as indicated on the rating sticker near the AC cord on the

back of the unit).

3. Select suitable module block(s) or appropriate water volume and put the

block(s) into the Corning LSE Digital Dry Bath Heater.

4. Turn the AC power On.

5. Run temperature calibration procedure when using the instrument for

the first time.

6. Press the Temperature Up or Down keys to adjust to the desired

temperature.

7. Press the Timer Up or Down keys to adjust to the desired time.

8. Press the Start/Stop key to start heating.

9. If you need to reset the timer during heating, press the Start/Stop key to

deactivate heating.

10. Press the Start/Stop key again to stop the unit.

11. If the lid is to be used, align the shaded area on the dry bath surface

with the magnet of the lid to attach it to the housing. To remove the

lid, press one hand firmly on the housing and use the other hand to pull

the lid off. To use the lid, the tube should not exceed 25 mm above the

heating block.

6.0 Calibration

Calibration allows the unit temperature display to be adjusted or matched

to the temperature of a single sample or to a calibrated thermometer,

thereby making an independent temperature measure of the block.

Corning LSE Digital Dry Bath Heaters are calibrated at the factory at 40°C

using a standard small hole-pattern block. If you are using a block with

a high heat loss rate, such as a block with large holes or a platform style

block, you may choose to recalibrate the unit to your specific application.

Also, if you are using very loose or odd shaped vessels, the calibration

function can help you match the display temperature to your actual sample

temperature.

To calibrate the unit for a given block or sample, first turn the unit off using

the On/Off switch. Then place a thermometer of known accuracy* into

the block thermometer hole or a thermocouple or other sensor into your

sample. Make sure there is a good fit between the thermometer and the

block or good contact between any sensor and sample or sensor and block.

To calibrate the block or sample to the display:

1. Press and hold the Start/Stop key, then simultaneously power up the

unit with the On/Off switch.

2. You should hear a “DU-DU-DU” sound from the dry bath and the

display will have one segment flashing on the left and will show a set

temperature, and the right will show adjt.

3. Use the Temperature Up and Down arrow keys to set the desired

temperature at which you want to calibrate the unit. Then press the

Start key.

4. Allow a minimum of 10 minutes (maximum 20 minutes) for the unit to

heat up to your set temperature and to equilibrate at this temperature.

The entire LED display will start flashing when equilibration is reached.

5. After the entire display has started flashing, read the thermometer (or

sensor meter) and use the Up and Down arrow keys to adjust the display

to the thermometer or sensor reading. Then press the Start/Stop key.

6. The unit will then begin to automatically adjust its operating temp-

erature to your original set point with the recalibration factor included.

Allow sufficient time for the unit to re-equilibrate, then compare the

thermometer or sensor reading to the calibrated display again. They

should closely match. If not, repeat the calibration procedure.

7.0 USB Interface

Corning® LSE™ Digital Dry Bath Heaters have a USB unidirectional data port.

A cable and software are available which allow a user to use a desktop or

laptop computer to record and/or print a record of the temperature profile

produced by the dry bath.

*Thermometers used for calibration purposes should have a written calibration certificate

and be traceable back to NIST or other certified body. General lab thermometers are often

not accurate enough for calibration work.

8.0 Troubleshooting Guide

Problem Solution

Display/LEDs do not light up 1. Check power cord and outlet.

2. Check On/Off switch.

3. Check fuse.

4. Contact Corning Life Sciences for service.

Unit not heating 1. Is set point below room temperature?

2. Is “Start” LED illuminated?

3. Press “Start” key.

4. Contact Corning Life Sciences for service.

Unit display overshoots 1. Normal operation. Display set point in

heat-up overshoots on initial heat-up

but block and sample do not overshoot

(see Operation section).

Block or sample temperature 1. Is unit in heating mode?

not the same as display 2. Is unit sitting in a drafty area?

temperature 3. Check accuracy of thermometer.

4. Is thermometer making good contact?

5. Follow calibration procedure.

9.0 Service and Repair Information

If you have a question about the Corning® LSE™ Digital Dry Bath Heater or

have a service inquiry, contact Corning Customer Service immediately at:

 1.800.492.1110 (for toll-free calling within the U.S. and Canada)

 1.978.442.2200 (outside the U.S.), or

 Contact your local Corning support office listed in the back of this manual.

Before returning any unit for service, a Return Authorization (RA) number

must first be obtained. Equipment sent in without prior authorization

will be returned at the customer’s expense. When returning a unit to

Corning for service, it should be sent in the original packaging. If this is not

possible, be sure that the unit is sufficiently packed. Any damage resulting

from improper packaging is the responsibility of the customer. A written

explanation should accompany the unit along with the RA number.

10.0 Cleaning and Maintenance

Make sure that the Corning® LSE™ Digital Dry Bath Heater and block are

cool and the power cord is disconnected before performing any cleaning

or maintenance. Repair or maintenance should only be performed by an

authorized service technician.

The dry bath may be cleaned with a moist cloth containing a mild soap

solution. Do not immerse the dry bath in water or any liquid.

The blocks may also be cleaned in a mild soapy solution. Be sure that all

items have thoroughly dried before attempting to connect the cord or use

the unit.

Spills: In the event liquid is accidentally spilled into the bath or well area,

disconnect the plug from the outlet and turn the unit upside down to

minimize liquid contact with the internal components. Remove the bottom

cover and inspect to assure liquid has not contacted heater elements,

electronic controls, or connectors. Have a qualified service technician clean

the unit and replace any damaged parts.

11.0 Equipment Disposal – European Regulations

According to Directive 2012/19/EU of the European Parliament and of the

Council of 4 July 2012 on waste electrical and electronic equipment (WEEE),

the Corning LSE Digital Dry Bath Heater is marked with the crossed-out

wheeled bin and must not be disposed of with domestic waste.

Consequently, the buyer shall follow the instructions for reuse and recycling

of waste electronic and electrical equipment (WEEE) provided with the

products and available at the following link: www.corning.com/weee

12.0 Appendix: Symbols and Conventions

The following chart is an illustrated glossary of the symbols that may be

used in this manual or on the product.

CAUTION: This symbol refers you to important operating

and maintenance (servicing) instructions within the product

Instruction Manual. Failure to heed this information may

present a risk of damage or injury to persons or equipment.

ATTENTION: Hot Surface.

Indicates disposal instruction.

DO NOT throw this unit into a municipal trash bin when this

unit has reached the end of its lifetime. To ensure utmost

protection of the global environment and minimize pollution,

please recycle this unit.

13.0 Limited Warranty

Corning Incorporated (Corning) warrants that this product will be free

from defects in material and workmanship for a period of three (3) years

from date of purchase. This warranty is valid only if the product is used for

its intended purpose and within the guidelines specified in the supplied

instruction manual.

Should this product require service, contact Corning Customer Service

department at 1.800.492.1110 or 978.492.1110 to receive a return

authorization number and shipping instructions. Products received without

proper authorization will be returned. All items returned for service should

be sent postage prepaid in the original packaging or other suitable carton,

and padded to avoid damage. Corning will not be responsible for damage

incurred by improper packaging. Corning may elect for onsite service for

larger equipment.

This warranty does not cover damage caused by accident, neglect, misuse,

improper service, natural forces, or other causes not arising from defects

in original material or workmanship. This warranty does not cover motor

brushes, fuses, light bulbs, batteries, or damage to paint or finish. Claims for

transit damage should be filed with the transportation carrier.

ALL WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION OF

36 MONTHS FROM THE ORIGINAL DATE OF PURCHASE.

CORNING’S SOLE OBLIGATION UNDER THIS WARRANTY IS LIMITED TO THE

REPAIR OR REPLACEMENT, AT CORNING’S DISCRETION, OF A DEFECTIVE

PRODUCT. CORNING IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGE, COMMERCIAL LOSS, OR ANY OTHER DAMAGES RESULTING FROM

THE USE OF THIS PRODUCT.

Some states do not allow limitation on the length of implied warranties

or the exclusion or limitation of incidental or consequential damages. This

warranty gives you specific legal rights. You may have other rights which

vary from state to state.

No individual may accept for, or on behalf of Corning, any other obligation

of liability, or extend the period of this warranty.

For your reference, make a note of the model and serial number, date of

purchase, and supplier here.

Model No. ____________________ Serial No. _______________________________

Date Purchased ___________________________________________________________

Supplier _________________________________________________________________

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels CORNING Équipement de laboratoire

CORNING

CORNING PC-400D Manuel utilisateur

CORNING

CORNING AXYGEN AxySpin R Manuel utilisateur

CORNING

CORNING Axygen Axypet Manuel utilisateur

CORNING

CORNING Lambda EliteMax Manuel utilisateur

CORNING

CORNING Matribot 6150 Manuel utilisateur

CORNING

CORNING LSE 6703 Manuel utilisateur

CORNING

CORNING LSE 6785-SB Manuel utilisateur

CORNING

CORNING Matribot Bioprinter Manuel utilisateur

CORNING

CORNING LSE 6780-4 Manuel utilisateur

CORNING

CORNING LSE 6755 Manuel utilisateur

CORNING

CORNING Axygen Manuel utilisateur

CORNING

CORNING OptiTect Manuel utilisateur

CORNING

CORNING LSE 6703 Manuel utilisateur

CORNING

CORNING Axygen Axypet Pro Manuel utilisateur

CORNING

CORNING Labnet Prism R Manuel utilisateur

CORNING

CORNING Everon 6000 Manuel utilisateur

CORNING

CORNING LSE Series Manuel utilisateur

CORNING

CORNING Lambda EliteMax Manuel utilisateur

CORNING

CORNING LSE 6783 Manuel utilisateur

CORNING

CORNING PC-611 Manuel utilisateur

CORNING

CORNING Axygen MotoPet Manuel utilisateur

CORNING

CORNING 6928 Manuel utilisateur

CORNING

CORNING Lambda Plus Manuel utilisateur

CORNING

CORNING LSE 6775 - 120V US Manuel utilisateur

Manuels Équipement de laboratoire populaires d'autres marques

Qiagen

Qiagen DML 3000 Manuel utilisateur

Queensgate

Queensgate NANOSCAN OP400 Manuel de programmation

Conviron

Conviron GEN1000-GE Manuel utilisateur

Parr Instrument

Parr Instrument 4560 Mode d’emploi

IKA

IKA IC control Manuel utilisateur

Integra

Integra DOSE IT Manuel utilisateur

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuel utilisateur

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuel utilisateur

NI PXI-5422 Manuel

Collomix

Collomix Aqix Manuel utilisateur

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur

Ocean Insight

Ocean Insight FLAME-NIR+ Manuel utilisateur

Parker

Parker ALIGN-MG-NA Manuel utilisateur

BD 644787 Manuel utilisateur

DENTAURUM

DENTAURUM Compact Megaplus Manuel utilisateur

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuel utilisateur

VWR

VWR SAS Super IAQ Manuel utilisateur

illumina

illumina MiSeqDx Manuel utilisateur