Contec DAI12-4GY Manuel utilisateur

F&eIT Series

Isolated Analog Output Module

DAI12-4(FIT)GY

User’s Manual

CONTEC CO., LTD.

DAI12-4(FIT)GY i

Check Your Package

Thank you for purchasing the CONTEC product.

The product consists of the items listed below.

Check, with the following list, that your package is complete. If you discover

damaged or missing items, contact your retailer.

Product Configuration List

- Module …1

- First Step Guide …1

- CD-ROM [F&eIT Series Setup Disk] *1…1

- Interface connector plugs ...2

- Warranty Certificate …1

- Serial number label …1

*1 The CD-ROM contains various software and User’s Manual (this manual)

Module Interface connector plug

CD-ROM

First step guide[F&eIT Series Setup Disk]

RUN STAT US

DAI12-4

Device

CH0

CH1

CH2

CH3

Warranty Certificate

XXXXXXXXXXXXX

Serial number label

Warranty

Certificate

ii DAI12-4(FIT)GY

No part of this document may be copied or reproduced in any form by any means

without prior written consent of CONTEC CO., LTD.

CONTEC CO., LTD. makes no commitment to update or keep current the information

contained in this document.

The information in this document is subject to change without notice.

All relevant issues have been considered in the preparation of this document. Should

you notice an omission or any questionable item in this document, please feel free to

notify CONTEC CO., LTD.

Regardless of the foregoing statement, CONTEC assumes no responsibility for any

errors that may appear in this document nor for results obtained by the user as a result

of using this product.

Trademarks

F&eIT is a registered trademark or trademark of CONTEC CO., LTD. Other

company and product names that are referred to in this manual are generally

trademarks or registered trade trademark.

DAI12-4(FIT)GY iii

Table of Contents

Check Your Package .......................................................... i

Trademarks .......................................................................ii

Table of Contents .............................................................iii

1. Introduction .................................................................. 1

Features ........................................................................ 1

Functions and control method by controller connected2

Limited One-Year Warranty ........................................ 4

How to Obtain Service.................................................. 4

Liability......................................................................... 4

Handling Precautions................................................... 5

About the Manual......................................................... 6

2. Module Nomenclature and Settings............................... 7

Nomenclature of Module Components............................. 7

Setting a Device ID........................................................... 8

Setup Method................................................................ 8

LED Indicator ................................................................... 8

3. Connecting to an External Device ................................. 9

Interface Connector .......................................................... 9

How to Connect an Interface Connector ..................... 9

Signal Layout on the Interface Connector ................ 10

Connecting an Analog Output Signal ............................ 11

Connecting a Voltage Output..................................... 11

Connecting a Current Output.................................... 13

4. Using the I/O Address Map ......................................... 15

Starting I/O Address....................................................... 15

List of I/O Address Maps ................................................ 16

Specifications Common to F&eIT Products................... 18

Product Information ................................................... 18

Overview of the D/A Conversion Function .................... 20

Details on the Analog Output Status ........................ 28

List of Commands........................................................... 31

Examples......................................................................... 32

iv DAI12-4(FIT)GY

Software Mode............................................................ 32

Clock Mode (No Interrupts) ....................................... 34

Clock Mode (with Interrupts) .................................... 37

5. Using the Memory Address Map.................................. 43

Module Settings Area................................................. 44

Module Information Area........................................... 47

Basic Output Data Area............................................. 49

Examples......................................................................... 51

6. System Reference ........................................................ 55

Block Diagram ................................................................ 55

Specifications.................................................................. 56

External Dimensions...................................................... 58

Introduction

DAI12-4(FIT)GY 1

Introduction

Congratulations on your recent purchase of an Insulator Digital Output Module.

The DAI12-4(FIT)GY can control external devices by converting digital data that is

output from a, F&eIT-series controller module <CPU-CAxx(FIT)GY,

CPU-SBxx(FIT)GY etc> into either voltage or current-based analog signals. The

insulation between external signals and the Controller Module permits the use of the

Controller Module without compromising the communications features of the latter.

By reading this manual carefully, please build a system by creating applications

programs, setting the switches, and connecting the module to external devices.

Features

-The output range is common to different channels, and can be selected from five

output ranges: 0 - 1 0 V, 0 - 5V, ±10V, ±5V, and 0 - 20mA.

-A rotary switch that is provided allows you to set device IDs to help you keep track of

device numbers.

-The system incorporates a screwless connector plug that allows you to easily attach

and detach wires without using any special tools.

-Similar to other F&eIT series products, the system, in the module itself, incorporates a

35mm DIN rail mounting mechanism as a standard item. A connection to a

controller module can be effected on a lateral, stack basis in a unique configuration,

which permits a simple, smart system configuration without the need for a backplane

board.

Introduction

2DAI12-4(FIT)GY

Functions and control method by controller connected

The DAI12-4(FIT)GY can be connected to a variety of controllers.

Micro Controller Unit : CPU-SBxx(FIT)GY

I/O Controller Module : CPU-CAxx(FIT)GY

Monitoring & Control Server Unit : SVR-MMF2(FIT)

Monitoring & Control Server Unit : SVR-MMF(FIT)GY

Isolated Analog Output Module for USB : DAI12-4 (USB)GY

I/O Controller Module with USB : CPU-CA10(USB)GY

The functions and control of the DAI12-4(FIT)GY vary with the controller to which the

DAI12-4(FIT)GY is connected.

Functions available with each controller connected

*1 For the function available, refer to the reference manual for the SVR-MMF2(FIT), SVR-MMF(FIT)GY.

*2 Pacer clock setting: 10 - 1,073,741,824 microseconds

*3 Using the sampling timer built in the DAI12-4(USB)GY

The setting range is from 1000 to 1,073,741,000 microseconds.

CPU-SBxx(FIT)GY

CPU-CAxx(FIT)GY

SVR-MMF2(FIT)

SVR-MMF(FIT)GY

DAI12-4(USB)GY

CPU-CA10(USB)GY

Software input range setting

ο ο ο ο

D/A conversion with software command

ο ο ο ο

Continuous D/A conversion using the internal pacer clock

Multi-channel simultaneous output function

ο ο ο

Interrupt function

Device ID setting range 0 - 7 0 - 7 0 - 7 0 - 7 1 - 3 0 - 7

Introduction

DAI12-4(FIT)GY 3

Control method by controller connected

* The API-SBP(W32) is included in the development kit

DTK-SBxx(FIT); the other drivers are bundled with each controller.

Control using the I/O address map

When connected to the CPU-SBxx(FIT)GY, the DAI12-4(FIT)GY can receive I/O

instructions directly from the controller module. For details, see Chapter 4 “Using the

I/O Address Map”.

Control using the memory address map

When connected to the CPU-CAxx(FIT)GY, the DAI12-4(FIT)GY can be accessed

from the host computer over the network.

The DAI12-4(FIT)GY is assigned with its device ID in the memory managed by the

controller module. The application running on the host computer controls the module

by reading/writing the memory managed by the controller module. For details, see

Chapter 5 “Using the Memory Address Map”.

Control via the Windows driver

For the functions and settings available when using the Windows driver, refer to the

reference manual and online help for each module.

Control over the web

You can monitor collected data and manage the log over the web. You can use your

familiar browser to easily make various settings. For details, refer to the reference

manual for the SVR-MMF2(FIT), SVR-MMF(FIT)GY.

CPU-SBxx(FIT)GY

CPU-CAxx(FIT)GY

SVR-MMF2(FIT)

SVR-MMF(FIT)GY

DAI12-4(USB)GY

CPU-CA10(USB)GY

Control using the I/O address map

Control using the memory address map

FIT Protocol

API-CAP(W32)

API-SBP(W32)

API-USBP(WDM)

ο ο

Control over the web

ο ο

Control via the Windows driver *

Introduction

4DAI12-4(FIT)GY

Limited One-Year Warranty

CONTEC F&eIT products are warranted by CONTEC CO., LTD. to be free from

defects in material and workmanship for up to one year from the date of purchase by

the original purchaser.

Repair will be free of charge only when this product is returned freight prepaid with a

copy of the original invoice and a Return Merchandise Authorization to the distributor

or the CONTEC group office, from which it was purchased.

This warranty is not applicable for scratches or normal wear, but only for the electronic

circuitry and original products.

The warranty is not applicable if the device has been tampered with or damaged

through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is

not included, in which case repairs will be considered beyond the warranty policy.

How to Obtain Service

For replacement or repair, return the device freight prepaid, with a copy of the original

invoice. Please obtain a Return Merchandise Authorization Number (RMA) from the

CONTEC group office where you purchased before returning any product.

* No product will be accepted by CONTEC group without the RMA number.

Liability

The obligation of the warrantor is solely to repair or replace the product. In no event will

the warrantor be liable for any incidental or consequential damages due to such defect or

consequences that arise from inexperienced usage, misuse, or malfunction of this device.

Introduction

DAI12-4(FIT)GY 5

Handling Precautions

Take the following precautions when handling this module.

- Do not modify the module. CONTEC will bear no responsibility for any problems,

etc., resulting from modifying this module.

- Do not use or store the equipment in a hot or cold place, or in a place that is subject

to severe temperature changes (Operating temperature range: 0 - 50°C).

- Do not use or store the equipment in a place subject to direct sunlight or near a

heating device, such as a stove.

- Do not use or store the equipment in a dusty or humid place. (Operating humidity

range: 10 - 90%RH, No condensation)

- As this product contains precision electronic components, do not use or store in

environments subject to shock or vibration.

- Do not use or store the product near equipment generating a strong magnetic field or

radio waves.

- If you notice any strange odor or overheating, please unplug the power cord

immediately.

- In the event of an abnormal condition or malfunction, please consult the dealer from

whom the equipment was purchased.

- To avoid electric shock, please do not touch the system with a wet hand.

- Do not open the module casing. CONTEC will disclaim any responsibility for

equipment whose casing has been opened.

- To prevent damage, please do not subject the module to impact or bend it.

- To prevent contact malfunction, please do not touch the metallic pins on the external

module connector.

- The module contains switches that need to be properly set. Before using the

module, please check its switch settings.

- To avoid malfunction, please do not change the module switch settings in an

unauthorized manner.

- Do not operate the device module when the power for the Controller Module is on.

To avoid malfunction, please be sure to turn off the power for the Controller Module.

- If you use this product in a noisy environment, attach ferrite cores to the IO cable to

stabilize the operation.

- Regarding “CE EMC Directive Notice”.

Please connect the Interface Connector with a shielded cable to

meet the mentioned standard above.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Contec Unité de contrôle

Contec

Contec CPSN-SSI-4C Manuel utilisateur

Contec

Contec F&eIT Series Manuel utilisateur

Contec

Contec ADI16-4(FIT)GY Manuel utilisateur

Contec

Contec AI-1608VIN-USB Manuel utilisateur

Contec

Contec CONPROSYS Series Manuel utilisateur

Contec

Contec CPS-AO-1604LI Manuel utilisateur

Contec

Contec Conprosys CPS-MC341-ADSC1-111 Manuel utilisateur

Contec

Contec PLUG-IN PTI-4GY Manuel utilisateur

Contec

Contec CNT24-2GY Manuel utilisateur

Contec

Contec F&eIT Series Manuel utilisateur

Contec

Contec COM-4CN-USB Manuel utilisateur

Contec

Contec CPS-DO-16L Manuel utilisateur

Contec

Contec CONPROSYS CPS-MCS341-DS1-111 Manuel utilisateur

Contec

Contec CNT16-8GY Manuel utilisateur

Contec

Contec F&eIT Series Manuel utilisateur

Contec

Contec CONPROSYS nano CPSN-CNT-3201I Manuel utilisateur

Contec

Contec RRY-16CX-USB Manuel utilisateur

Contec

Contec DS540-MPCI4W Manuel utilisateur

Contec

Contec CONPROSYS Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur