Connects2 CAM-FD24 Manuel utilisateur

www.c2vision-eu.com

Image Sensor: 1/3” CMOS

TV Lines: 700

Resolution: 976 x 592

Minimum Illumination: 0.1 Lux (0 Lux when LED is on)

TV System: NTSC

Waterproof Rating: IP68

Horizontal Angle: 80 Degrees

Vertical Angle: 145 Degrees

Diagonal Angle: 170 Degrees

Video Output: 1.0V p-p 75ohm

Parking Guidelines: Yes (Removable)

Operating Voltage: 12V DC (Negative Ground)

Operating Temperature: -20 Degrees C to +70 Degrees C

User Manual

Prior to Installation

Read the manual prior to installation. Technical knowledge is necessary for installation.

Please ensure you use the correct tools to avoid damage to the vehicle or product.

Connects2 can not be held responsible for the installation of this product.

Technical Support

Connects2 want to provide a fast and suitable resolution should you encounter any

technical issues. With this in mind, when contacting Connects2, try to provide as

much Information as possible. This will speed up the process and help us to help you.

Please use our dedicated online technical support centre: support.connects2.com

Dual Lens Brake Light Camera

Ford Transit Custom 2012 - 2015

PRODUCT FEATURES:

DISCLAIMER:

CAM-FD24

Connects2Vision

www.c2vision-eu.com

CONTENTS

• Camera with Male 7pin camera connector

• 10m Female 7pin to Male 7pin extension cable

• 7pin Male aviation connector to 2x Female 4pin connectors (1x Yellow, 1x Black)

• 2x 4pin Male aviation connectors to 2x Female RCA’s (1x Yellow, 1x Black)

• 2x DC power cables with Male DC connector to bare wires

• 2x Male to Male RCA adapters

• 3M camera shaped foam pad

• Instructions

INSTALLATION

1. Remove the third brake light from the vehicle and unplug the connection

cable.

2. Ret the CAM-FD24 (if needed, with the use of the 3M foam pad) to the

vehicle, taking care not to trap any cables.

3. Connect the 7pin of the extension cable to the camera and thread through

the vehicle

4. Attach the Female 7pin connector from the extension to the 7pin to dual

4pin adapter.

5. Take the 2x 4pin connections and attach both the 4pin connectors found on

the RCA/DC split wire.

6. Use both the DC power cables to plug into the black connector and

proceed to wire the red to a source of 12V and black to a source of ground.

7. Use the RCA adpater to plug into the yellow RCA on the harness, and

proceed to plug this into the aftermarket accessory’s video input(s).

8. Test the camera connection by turning on the ignition. The rear camera feed

should now be visible on screen. Put the vehicle into reverse and the reverse

camera feed will automatically populate on screen.

If camera feed is unresponsive, please uninstall the wiring and reinstall carefully

in accordance with the above steps.

9. The camera will be default with parking guidelines. To remove this, simply cut

the black loop wire found on the camera’s connector.

For further help and support, please contact us directly at

support.connects2.com/tickets/technical

and ll out a support ticket with the full details of your issue.

Subscribe to our YouTube Channel for installation

guides and tips... www.youtube.com/connects2

Table des matières

Autres manuels Connects2 Caméra embarquée

Connects2

Connects2 Vision CAM-16 Manuel utilisateur

Connects2

Connects2 CAM-MB9 Manuel utilisateur

Connects2

Connects2 CAM-FD14 Manuel utilisateur

Connects2

Connects2 CAM-SK2-AD Manuel utilisateur

Connects2

Connects2 CAM-VW1-AD Manuel utilisateur

Connects2

Connects2 CAM-1 Manuel utilisateur

Connects2

Connects2 Vision CAM-26 Manuel utilisateur

Connects2

Connects2 CAM-VW9.2 Manuel utilisateur

Connects2

Connects2 Vision CAM-14 Manuel utilisateur

Connects2

Connects2 CAM-KIT8 Manuel utilisateur

Connects2

Connects2 CAM-FT3 Manuel utilisateur

Connects2

Connects2 CAM-FT5 Manuel utilisateur

Connects2

Connects2 Vision CAM-FD13 Manuel utilisateur

Connects2

Connects2 Vision CAM-KIT7 Manuel utilisateur

Connects2

Connects2 CAM-JG1-AD Manuel utilisateur

Connects2

Connects2 CAM-PO1-AD Manuel utilisateur

Connects2

Connects2 Vision CAM-34 Manuel utilisateur

Connects2

Connects2 Vision CAM-37 Manuel utilisateur

Connects2

Connects2 Vision AM-44 Manuel utilisateur

Connects2

Connects2 CAM-AU5 Manuel utilisateur

Connects2

Connects2 Connects2Vision CAM-LR2-AD Manuel utilisateur

Connects2

Connects2 CAM-PE2 Manuel utilisateur

Connects2

Connects2 CAM-AU6 Manuel utilisateur

Connects2

Connects2 Vision CAM-FD25 Manuel utilisateur

Manuels Caméra embarquée populaires d'autres marques

Cansonic

Cansonic UltraDuo Z2 Manuel utilisateur

Gazer

Gazer F720 Manuel utilisateur

HP f500g Manuel utilisateur

Xblitz

Xblitz TANGO 4K Manuel utilisateur

Rexing

Rexing M1 Manuel utilisateur

Maka Technologies

Maka Technologies Marbella MXPro Manuel utilisateur

NESA

NESA NRC-80DLM Instructions d'installation et d'utilisation

Kaiser Baas

Kaiser Baas R20 Manuel utilisateur

Boyo

Boyo VTM43TC Manuel utilisateur

Minolta

Minolta MNCD37 Manuel utilisateur

Thinkware

Thinkware FA10 Manuel utilisateur

Momento

Momento MD-5200 Manuel utilisateur

BlackVue

BlackVue DR590X-1CH Manuel utilisateur

HP F300 Manuel utilisateur

CammSys

CammSys BlackSys BH-300 Manuel utilisateur

Snooper

Snooper DVR-2HD Manuel utilisateur

Lukas

Lukas Q900 Manuel utilisateur

RVS

RVS 450C Manuel utilisateur