Comtrol ROCKET LINX ES7506 Manuel utilisateur

QUICK INSTALLATION GUIDE

2000528 Rev D | Release Date - January, 2014

ROCKETLINX ES7506

Industrial 6-Port Managed PoE Switch

INTRODUCTION

The RocketLinx 7506 is designed for industrial PoE applicaons where the

power source is not conveniently located, such as IP surveillance or wireless

access points.

See the Comtrol website for complete product specicaons.

INSTALLATION OVERVIEW

You can use the following overview to install the ES7506. If you need more

detailed installaon and conguraon informaon, you can refer to the

RocketLinx ES7506 User Guide

, which is available on the RocketLinx CD or

you can download the latest version.

Wiring the Power Inputs

The ES7506 provides redundant power, reverse polarity protecon, and

accepts a posive or negave power source but PW1 and PW2 must apply

to the same mode. The power supplies should be UL Listed with a minimum

output rang of 24-55VDC and at 2.5A.

Electrical Specicaons Values

Power Input

Voltage

PWR1/PWR2

IEEE 802.3af Standard, Manual 48 (48-57VDC)

IEEE 802.3af Ultra 55 (55-57VDC)

Forced 15.4W 48 (48-57VDC)

Forced 30W 55 (55-57VDC)

PoE Output Voltage IEEE 802.3af Standard, Manual 44-57V

IEEE 802.3af Ultra 50-57V

Forced 44-57V

Maximum PoE

Power/Port

IEEE 802.3af Standard, Manual 15.4W

IEEE 802.3af Ultra, Forced 30W

Total Power Budget Maximum Up to 100 W

Power Consumpon Maximum 8W without PD

load

1. Insert the posive and negave wires into PW+ and PW- contacts (PW1

and PW2). You can connect a single power supply or two power supplies

depending on your requirements.

2. If both power inputs are connected, the ES7506 is powered from the

highest connected voltage. The unit can be congured to signal an alarm

for loss of power in either PW1 or PW2.

3. Tighten the wire-clamp screws to prevent the wires from being

loosened.

Power should be disconnected

from the power supply before

connecng it to the switch.

Otherwise, your screwdriver

blade can inadvertently

short your terminal

connecons to the grounded

enclosure.

Wiring the Alarm Relay Output

The alarm relay output or digital

output (DO) contacts are on the

terminal block connector on the side of the ES7506. The power supply

should be UL Listed with a minimum output rang of 2.5A at 24-55VDC.

The relay contacts are energized (open) for normal operaon and close

under faulty condions. Faulty condions can include power failure, Ethernet

port link break, or other predened events congurable in the ES7506 user

interface. To acvate the alarm relay output funcon, refer to the

RocketLinx ES7506 User Guide

Power Supply AC Power Input

24-55VDC/2.5A

(UL Listed)

V-

V+

Wiring Posive Power Supplies

Power Supply AC Power Input

12-24AWG

12-24AWG V-

V+

DC Power Input

24-55VDC

DC Power Output 24-55VDC/2.5A

(UL Listed)

Alm PWR2PWR1

+-+ -

Grounding the E7506

Wire the earth ground to ensure the system is not damaged by noise or any

electrical shock, we recommend that you make a direct connecon between

the ES7506 and earth ground.

Using a screw driver, loosen the earth ground screw on the side of the

ES7506 and then ghten the screw aer the earth ground wire is connected.

Mounng the ES7506

Use the appropriate procedure to mount the ES7506 on the wall or a DIN rail.

Connecng RJ45 Ports

Connect one end of an Ethernet cable into the Ethernet port of the ES7506

and the other end to the aached networking device. The Ethernet ports

support 10/100Mbps half/full-duplex. All ports auto-detect the signal from

connected devices to negoate the link speed and duplex mode. Auto

MDI/MDIX allows users to connect another switch, hub, or workstaon

without changing straight through or crossover cable.

Link/Act LEDs are lit to indicate trac and link status, see the LEDs subsecon

for more informaon.

Attaching the ES7506 to the Wall

Use the hook holes located at the corners of

the wall-mount plate to mount the ES7506.

DIN Rail Mounting

Two DIN rail clips and four screws were shipped

with the ES7506. Use the screws to attach the

DIN rail clip to the wall-mount plate.

Always make sure that the cables between the

switches and aached devices (for example,

switch, hub, or workstaon) are less than 100

meters (328 feet).

• 10BASE-T: Category 3, 4, or 5 cable

• 100BASE-TX: Category 5 cable

• IEEE 802.3af: Category 5 cable

PROGRAMMING THE IP

ADDRESS

Congure the IP address using one of the

following methods:

• PortVision DX (available on the RocketLinx CD shipped with the product)

• Web browser

• Telnet

• Command Line Interface (CLI) using the RS-232 console cable

The easiest way to congure a stac IP address for your network in the

ES7506 is to use a Windows host and PortVision DX (see below). For

informaon about using other conguraon methods, refer to the

RocketLinx ES7506 User Guide.

Note: Oponally, you can use NetVision if you are accustomed to using NetVision.

PortVision DX is replacing NetVision. NetVision is not documented in the

RocketLinx ES7506 User Guide.

The following procedure uses PortVision DX to program network sengs.

1. Install PortVision DX on a host system with a Windows operang

system. If you need assistance installing PortVision DX, see the

RocketLinx ES7506 User Guide.

2. Start PortVision DX. PortVision DX can be started from Start --> All

Programs --> Comtrol --> PortVision DX.

3. Click the Scan buon.

4. Select the Comtrol product families that you want to locate and click the

Scan buon.

(cont. on page 5)

10/100BASE-TX PoE

(Alternave B)

1 RX+

2RX-

3 TX+

4,5 Vport+

6TX-

7,8 Vport-

(cont. from page 4)

5. Right-click the ES7506 in the

Device List

pane (lower) that you want to

congure and click Properes.

6. Enter a user-friendly Device Name.

7. Oponally, enter the ES7506 serial number, which displays a friendly

device name in the

Device List

pane on the main page.

8. Select DHCP IP or Stac IP for the IP Mode.

• If you select DHCP IP, go to Step 9.

• If you select Stac IP, enter an IP address, Subnet Mask, and

Default Gateway value for your network.

9. Oponally, select the appropriate Network Topology, which is an

informaonal eld.

10. Click the Apply Changes buon.

11. Click Close to return to the main screen.

You are now ready to congure the ES7506 features.

LED INDICATORS

You can also view the LEDs for the ES7506 through the web interface using

the

Device Front Panel

page.

LEDs LED On LED Blinking LED O

Alm

(Alarm)

Alarm acvated

or port link down

Not applicable Alarm not acvated

PW1/

PW2

Green: Power Not applicable No power

R.M.

(Ring

Master)

Green: Working

as a Ring Master

Amber: Ring

failed

Ring funcon disabled

PoE 1-4 Amber: PoE

powering

Blinking: PoE

Detect

Blinking fast: PoE

powering failure

PoE disabled: power

output over current, a

cable short, or PoE is

disabled for that port

LNK/ACT

1-6

Port link up Acve

connecon

Port link down or port

not connected

FEATURE CONFIGURATION

The ES7506 provides both in-band and out-band conguraon methods:

Out-band management means that you congure the ES7506 using the

RS-232 console cable and the Command Line Interface (CLI) to access the

ES7506 without aaching an admin PC to the network. You can also use

out-band management, if you lost the network connecon to the ES7506.

In-band management means that you connect remotely using the ES7506

IP address through the network. You can remotely connect with the ES7506

Java applet web interface or a Telnet console and the CLI.

The following procedure uses a web browser to congure ES7506 features.

Refer to the

RocketLinx ES7506 User Guide

for other conguraon methods.

1. If necessary, install the latest version of the Java Runme Environment,

which is required to run the web management interface.

2. Open a web browser and enter the IP address of the ES7506.

3. Click Run when Java prompts you to run the applet.

4. Enter admin for both the user name and the password when prompted.

5. Use the web interface to congure your device as needed for your

network.

You can use the help system or the

RocketLinx ES7506 User Guide

for

informaon about conguring ES7506 features.

COMTROL CUSTOMER SERVICE

You can use one of the following methods to contact Comtrol.

Contact Method Web Address or Phone Number

Support hp://www.comtrol.com/support

Downloads p://p.comtrol.com/html/ES7506_main.htm

Website hp://www.comtrol.com

Phone +1 763.957.6000

Autres manuels pour ROCKET LINX ES7506

Table des matières

Autres manuels Comtrol Changer

Comtrol

Comtrol RocketLinx ES8520-XT Manuel utilisateur

Comtrol

Comtrol RocketLinx ES7510 Manuel utilisateur

Comtrol

Comtrol RocketLinx ES8108 Manuel utilisateur

Comtrol

Comtrol RocketPort Serial Hub Si Manuel de l'opérateur

Comtrol

Comtrol RocketPort Manuel de la liste des pièces

Comtrol

Comtrol RocketLinx ES8108 Manuel utilisateur

Comtrol

Comtrol DeviceMaster DM-2000 Series Manuel de l'opérateur

Comtrol

Comtrol ROCKET LINX MP1204-XT Manuel utilisateur

Comtrol

Comtrol Rocketlinx ES8108-GigE Manuel utilisateur

Comtrol

Comtrol ROCKETLINX ES8509-XT Manuel utilisateur

Comtrol

Comtrol ROCKETLINX ES7105 Manuel utilisateur

Comtrol

Comtrol RocketLinx ES8105 Manuel utilisateur

Comtrol

Comtrol ROCKETLINX ES7206-XT Manuel utilisateur

Comtrol

Comtrol RocketLinx ES7506 Manuel utilisateur

Comtrol

Comtrol ROCKETLINX ES8509-XT Manuel utilisateur

Comtrol

Comtrol ROCKETLINX ES7510-XT Manuel utilisateur

Comtrol

Comtrol RocketPort RPUSBSH Manuel de l'opérateur

Comtrol

Comtrol ROCKETLINX ES7110-VB Manuel utilisateur

Comtrol

Comtrol ROCKETLINX ES8510 Manuel utilisateur

Comtrol

Comtrol RocketLinx ES8108 Manuel utilisateur

Comtrol

Comtrol RocketLinx MP1204-XT Manuel utilisateur

Comtrol

Comtrol ROCKET LINX ES7506 Manuel utilisateur

Comtrol

Comtrol RocketLinx ES8108 Manuel utilisateur

Comtrol

Comtrol ROCKETLINX ES8508 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur