CommScope NOVUX Manuel utilisateur

Installation Instructions

page 1 / 9

NOVUX™ Fiber Optic System

TC-1464-IP

Rev. A, January 2021

http://www.commscope.com

Cleaning the hardened connector and adapter

1 About this manual

This publication provides user information for the cleaning and maintenance of the full hardened connector and

adapter, and the HMFOC connector and adapter. Images in this manual are for reference only and are subject to

change.

2 Maintenance

Follow specific cleaning instructions outlined for each specific connection type using the below Inspect/Clean Cycle.

CommScope® is not responsible for damage caused by cleaning.

Contents

Contents1 About this manual............................................................................. 1

2 Maintenance....................................................................................... 1

3 Warnings and Cautions..................................................................... 3

4 Tools.................................................................................................... 3

5 Cleaning the full size hardened connector and adapter................3

5.1 Full size hardened connector cleaning................................................... 3

5.2 Full size hardened adapter cleaning........................................................4

6 Cleaning the HMFOC pinned/non-pinned connector....................5

6.1 Cleaning the pinned HMFOC connector................................................5

6.2 Cleaning the non-pinned HMFOC connector...................................... 6

6.3 Cleaning the pinholes on the non-pinned HMFOC

connector...........................................................................................................7

7 Trade-marks........................................................................................9

8 Contact information.......................................................................... 9

page 2 / 9

3 Warnings and Cautions

• Follow the installation instruction steps to ensure the performance of the closure. It is necessary to take

precautions and keep the working space clean to protect the closure sealing materials and splices.

• Exposure to laser radiation can seriously damage the retina of the eye. Do not look into the ends of any optical

fiber. Do not assume the laser power is turned off or that the fiber is disconnected at the other end. Looking into

the ends of any optical fiber is entirely at your own risk. A protective cap or hood MUST be immediately placed

over any radiating adapter or optical fiber connector to avoid the potential of dangerous amounts of radiation

exposure. This practice also prevents dirt particles from entering the connector and adapter.

• Fiber optic cables may be damaged if bent or curved to a radius that is less than the recommended minimum bend

radius. Always observe the recommended bend radius limit when installing fiber optic cables, subunits and patch

cords.

4 Tools

The following basic tools, auxiliary equipment, and materials are required for cleaning:

• 216B key tool (used to open optical port dust cap)

• Hardened connector/adapter cleaning kit

5 Cleaning the full size hardened connector and adapter

Use the following procedure for cleaning the hardened drop connector using the hardened connector/adapter cleaning

kit (accessory kit FHD-ACC-CLNKIT1).

5.1 Full size hardened connector cleaning

1. If the connector has been in use, clean the connector body, preferably using compressed air, to minimize

contaminants introduced to the ferrule.

2. Unscrew connector from its optical port or unscrew dust cap from the end of the connector.

3. Examine the end of the connector and determine which is the high side and which is the low side of the connector

end-face as shown in the figure above.

page 3 / 9

4. Open the tape shutter by squeezing the lever on the underside of the cassette and then keep the shutter open by

continuing to squeeze the lever.

5. Hold the end-face of the connector perpendicular to the cleaning tape and with the high side of the connector

pointing in the direction of cleaning as shown in the figure above.

Note: Do not use alcohol to clean the endface of the connector.

6. With light pressure, slide the connector end-face once across the tape in the direction shown using a smooth linear

motion. Do not press too hard and do not repeat the cleaning motion with the same tape.

7. Release the lever on the underside of the cassette to close the tape shutter.

8. Repeat steps 3 through 6 until the connector has been cleaned three times.

9. When the connector is clean, reinstall the drop cable dust cap and tighten until finger tight.

Note: Leave the drop cable dust cap on the connector until ready to connect the drop cable to an optical port.

5.2 Full size hardened adapter cleaning

1. If the adapter has been in use, clean around the port opening, preferably using compressed air, to minimize

contaminants introduced to the ferrule.

2. Unscrew the connector from its optical port or using a 216B key tool unscrew the optical port dust cap from the

adapter.

3. Insert a dry swab into the adapter as shown in the figure above.

Note: Do not apply alcohol to the swab or to the adapter.

4. While applying light pressure against the connector end-face, rotate the dry swab 360º three times.

5. Dispose of the dry swab after use.

page 4 / 9

6. When the connector end-face and adapter ferrule are clean, connect the drop cable to the optical port or reinstall

the optical port dust cap.

Note: The optical port is not sealed until a drop cable connector or optical port dust cap is mated to the port

adapter.

6 Cleaning the HMFOC pinned/non-pinned connector

6.1 Cleaning the pinned HMFOC connector

1. Inspect the pinned HMFOC connector with a low-resolution microscope and inspect the complete ferrule surface

including the area around the pins for dirt or guide pin damage. If dust, dirt or contaminants are detected, proceed to

step 2.

2. The following are directions for cleaning an HMFOC pinned connector using US CONEC IBC brand cleaning tool - MT

Series.

Locate the red adapter on the cleaning tool and place it on the tip of the cleaning tool. Orientate the red adapter on

the cleaning tool so that the outside key slot is on the top. Locate the square notch on the threaded portion of the

pinned HMFOC connector. Hold the connector so the square notch is facing up.

Insert the cleaning tool into the pinned HMFOC until the cleaning tool is flush against the connector end face. Push

the cleaning tool forward into the HMFOC connector until a click is heard, then release the tool. Repeat this cleaning

motion as required.

Note: Always follow the cleaning tool manufacturer’s cleaning instructions for best results.

page 5 / 9

3. Inspect the connector. If there are still contaminants, use a small amount of non-isopropyl alcohol solvent on one or

more 2.5mm fiber optic swabs to remove any remaining dust, dirt or contaminants from the ferrule end face and/or

from around the guide pins. Always use a new swab for each connector and always follow-up with a dry clean using the

cleaning tool procedure.

4. Connect the pinned connector to a non-pinned HMFOC or assemble the dust cap back on to the pinned connector

until ready to install.

6.2 Cleaning the non-pinned HMFOC connector

1. Inspect the pinned HMFOC connector with a low-resolution microscope and inspect the complete ferrule surface

including the area around the pins for dirt or guide pin damage. If dust, dirt or contaminants are detected, proceed to

step 2.

2. The following are directions for cleaning an HMFOC pinned connector using US CONEC IBC brand cleaning tool - MT

Series.

Locate the blue adapter on the cleaning tool and place it on the tip of the cleaning tool. Orientate the blue adapter

so that the key on the bottom inside is facing downward. Locate the outside indented key on the non-pinned HFMOC

connector and hold the connector so this indent is also facing downward.

page 6 / 9

Insert the cleaning tool over the non-pinned connector until it stops. Push the cleaning tool forward into the HMFOC

connector until a click is heard, then release the tool. Repeat this cleaning motion as required.

Note: Always follow the cleaning tool manufacturer’s cleaning instructions for best results.

3. Inspect the connector. If there are still contaminants, use a small amount of non-isopropyl alcohol solvent on one or

more 2.5mm fiber optic swabs to remove any remaining dust, dirt or contaminants from the ferrule end face and/or

from around the guide pins. Always use a new swab for each connector and always follow-up with a dry clean using the

cleaning tool procedure.

4. Connect the non-pinned connector to a pinned HMFOC or assemble the dust cap back on to the pinned connector

until ready to install.

6.3 Cleaning the pinholes on the non-pinned HMFOC connector

Note: Cleaning the pinholes on HMFOC connectors is the last resort for trouble-shooting a high loss connection,

and only applicable for experienced personnel.

1. Inspect the connector with a 50x inspection scope. If there are contaminants around the pinholes, they may need to

be cleaned according to the following procedure.

Wet the pink (0.4 mm) TePe brand dental (pinhole) brush with MicroCare FCC2 connector cleaner or equivalent cleaning

solution and insert the brush into the pinhole while turning the brush 90 degrees. The brush will bottom-out before the

handle reaches the ferrule end-face.

2. Pull the brush out of the hole while rotating 90 degrees and then inspect the pinhole with an inspection scope.

With the scope at 50x magnification, inspect the leading edge of the pinhole for debris. Then focus down the pinhole

page 7 / 9

(at least to the inner step diameter) for any remaining contamination. If additional cleaning is needed, verify that the

cleaning solution has not dried on the brush. If it has, apply more solution and proceed with the cleaning.

3. With the brush bottomed-out in the pinhole, rotate the handle back and forth at least three times (180 degrees in

each direction.

4. Pull the brush out of the hole while rotating 90 degrees and then inspect the pinhole with a scope. With the scope at

50x magnification, inspect the leading edge of the pinhole for debris. Then focus down the pinhole (at least to the inner

step diameter) for any other contamination.

5. Connect the non-pinned connector to a pinned HMFOC or assemble the dust cap back on to the non-pinned

connector until ready to install.

page 8 / 9

7 Trade-marks

All trademarks identified by ® are registered trademarks in the US and may be registered in other countries. All third

party product names, trademarks and registered trademarks are property of their respective owners.

This document is for planning purposes only and is not intended to modify or supplement any specifications or

warranties relating to CommScope products or services. CommScope is committed to the highest standards of business

integrity and environmental sustainability, with a number of CommScope’s facilities across the globe certified in

accordance with international standards, including ISO 9001, TL 9000, and ISO 14001.

Further information regarding CommScope’s commitment can be found at: https://www.commscope.com/corporate-

responsibility-and-sustainability.

This product may be covered by one or more U.S. patents or their foreign equivalents. For patents, see www.cs-pat.com

8 Contact information

Visit our website or contact your local CommScope representative for more information.

For technical assistance, customer service, or to report any missing/damaged parts, visit us at: http://

www.commscope.com/SupportCenter

page 9 / 9

Table des matières

Autres manuels CommScope Câbles et connecteurs

CommScope

CommScope PICABOND 60944-6 Manuel utilisateur

CommScope

CommScope LSX-288 Manuel utilisateur

CommScope

CommScope FOSC-450D Manuel utilisateur

CommScope

CommScope AMP NETCONNECT 1933352 Series Manuel utilisateur

CommScope

CommScope HELIAX FiberFeed HFT1206-24S49 Series Feuille d'instructions

CommScope

CommScope HELIAX MFJS6UDHNA00 Manuel utilisateur

CommScope

CommScope QWIK MPO Series Manuel utilisateur

CommScope

CommScope FOSC-OC-3 Manuel utilisateur

CommScope

CommScope LightCrimp Plus ST Manuel utilisateur

CommScope

CommScope FOSC 450 A Manuel utilisateur

CommScope

CommScope AMP NETCONNECT 1711357-1 Manuel utilisateur

CommScope

CommScope 760230938 Manuel utilisateur

CommScope

CommScope FACT Manuel utilisateur

CommScope

CommScope SYSTIMAX 360 iPatch... Manuel utilisateur

CommScope

CommScope FIST-RSKG-1 Manuel utilisateur

CommScope

CommScope SYSTIMAX VisiPatch CPC5562 Manuel utilisateur

CommScope

CommScope OmniReach FTTX Manuel utilisateur

CommScope

CommScope SYSTIMAX 360 iPatch PATCHMAX Manuel utilisateur

CommScope

CommScope TDUX-35 Manuel utilisateur

CommScope

CommScope SCIL-B Manuel utilisateur

CommScope

CommScope LightCrimp Plus SC Simplex Manuel utilisateur

CommScope

CommScope M2400 Series Manuel utilisateur

CommScope

CommScope AMP NETCONNECT 553454-1 Manuel utilisateur

CommScope

CommScope SYSTIMAX 360 iPatch 360-iP-G2-1U-LC-FX Manuel utilisateur

Manuels Câbles et connecteurs populaires d'autres marques

Philips

Philips SWA6310 Manuel utilisateur

StarTech.com

StarTech.com CRJ4550PK Manuel utilisateur

Nohau

Nohau EMUL-IP2K-PC Manuel utilisateur

Foxun

Foxun SX-SP144E-HD4K2K Manuel utilisateur

Philips

Philips SWA3305W Manuel utilisateur

opticis

opticis Stretch DVIM1-1P0x Manuel utilisateur

Volkswagen

Volkswagen VAS 6558A Manuel utilisateur

NEXIBO

NEXIBO N-13 Manuel utilisateur

CYP

CYP PU-1H3HBTL Manuel utilisateur

Allen-Bradley

Allen-Bradley 1784-u2dhp Manuel utilisateur

Global Caché

Global Caché Flex Link Blaster Manuel utilisateur

Hauppauge

Hauppauge USB-Live2 Manuel utilisateur

Fenix

Fenix MPSV 15 Manuel utilisateur

BEGA

BEGA 71 085 Manuel utilisateur

Tesla

Tesla HPWC Manuel utilisateur

GAMERON

GAMERON LUXURY TV CABLE Manuel utilisateur

molex

molex Milli-Grid Dual row 87568 Series Manuel utilisateur

Burndy

Burndy Continental Industries thermOweld CRE-7 Manuel utilisateur