CommScope F-042-GL-E Manuel utilisateur

www.commscope.com

Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.

All trademarks identified by ® or ™are registered trademarks or trademarks, respectively, of CommScope, Inc. A997-0086 G (5/19)

Page 1 of 8

A997-0086 Revision G, May 2019

F-042-GL-E, T-045-GL-E & T-041-GL-E For

Dual Band 33°Beamwidth Panel Antennas

General

This instruction sheet contains all necessary information required to assist in the correct

installation of the Large Dual Band 33°Beamwidth Panel Antennas. These antennas are

supplied with AISG-compatible remotely controlled electrical beam downtilt (RET). Mechanical

downtilt is also available if required, depending on the type of mounting kit selected.

Following symbols can be found next to text outlining important information.

Please follow the procedure marked with this symbol precisely.

Non-compliance may lead to damage of the product.

Handy tips when installing product.

Unpacking

Make sure that the antenna and the accessory items listed below are provided and have not

been damaged during transport.

•Antenna

•Mounting kit (mounting kit components for each configuration is shown in Figure 3, 4, 5,

7 & 8).

DO NOT STACK

UNPACKED

ANTENNAS

www.commscope.com

Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.

All trademarks identified by ® or ™are registered trademarks or trademarks, respectively, of CommScope, Inc. A997-0086 G (5/19)

Page 2 of 8

A997-0086

Installation Instructions

Ensure a torque spanner is used when tightening fasteners, see the mounting kit

diagrams on the following pages for the correct torque recommendations.

Ensure antenna is installed with the connectors at the bottom.

DO NOT PLACE

POINT LOADS ON

ANTENNA RADOME

DO NOT USE ROPE

OR CHAIN OR

SLING

ATTACHMENT

AROUND ANTENNA

FOR LIFTING

USE MOUNTING

BRACKETS FOR

LIFTING AS

SHOWN

www.commscope.com

Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.

All trademarks identified by ® or ™are registered trademarks or trademarks, respectively, of CommScope, Inc. A997-0086 G (5/19)

Page 3 of 8

A997-0086

Table 1: Mounting Kit Part Numbers for Different Lengths of Antenna

Assemble kit as per Figures 2 & 3 of this document

1. Attach the kits assembly to the antenna, before trying to clamp the

brackets to the pole.

For typical installations of antennas up to 1400mm (55.1") long the minimum

recommended pipe diameter is 60mm (2.4"). For antennas over 1400mm

(55.1") up to 1800mm (70.9") long the minimum recommended pipe diameter

is 75mm (3").

Mounting Kits

850 –1400mm

(33.5” – 55.1”)

Antennas

1400 –1800mm

(55.1” – 70.9")

Antennas

Fixed Downtilt

F-042-GL-E

Mechanical Downtilt

T-045-GL-E

T-041-GL-E

Do not install near power lines.

Power lines, telephone lines, and

guy wires look the same. Assume

any wire or line can electrocute you.

Do not install on a wet or windy day

or when lightning or thunder is in

the area. Do not use metal ladder.

Wear shoes with rubber soles

and heels. Wear protective

clothing including a long-sleeved

shirt and rubber gloves.

Figure 1: Correctly Assembled

Mounting Bracket for

Fixed Downtilt Antenna

Installation Instructions - Fixed Downtilt Mounting Kit for up to

1800mm (70.9") Antennas - (F-042-GL-E)

www.commscope.com

Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.

All trademarks identified by ® or ™are registered trademarks or trademarks, respectively, of CommScope, Inc. A997-0086 G (5/19)

Page 4 of 8

A997-0086

Assemble kit as per Figures 4 and 5 of this document.

1. Attach the lower and upper mounting bracket assemblies to the antenna,

before trying to clamp the brackets to the pole.

2. Downtilt angles of 0and 2through to 10in 1increments can be

obtained with the correct adjustment of the tilt arm bracket.

•For 0downtilt the tilt arm may be stowed as show in Figure 6.

•2-10downtilt can be achieved by aligning the corresponding hole in the

tilt arm to the pivot bracket which mates against the mounting pole, as shown

in Figure 6. The first hole is for 2downtilt, with each consecutive hole

resulting in an increased inclination of 1.

For typical installations the minimum recommended pipe diameter is 75mm (3").

Installation Instructions- Mechanically Adjustable Downtilt Mounting Kits for

850 - 1400mm (33.5” – 55.1”) Antenna’s (T-045-GL-E),

Bracket Spacing 716mm (28.2")

www.commscope.com

Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.

All trademarks identified by ® or ™are registered trademarks or trademarks, respectively, of CommScope, Inc. A997-0086 G (5/19)

Page 5 of 8

A997-0086

Figure 4: Lower Mounting Bracket Exploded Assembly

Figure 5: Upper Mounting Bracket Exploded Assembly

Figure 6: Upper Bracket Placement For Various Downtilts

Assemble kit as per Figures 7 and 8 of this document

1.Attach the lower and upper mounting bracket assemblies to the antenna, before

trying to clamp the brackets to the pole.

2.Downtilt angles of 0through to 12in 2increments can be obtained with the

correct adjustment of the tilt arm bracket.

•For 0downtilt the tilt arm may be stowed as show in Figure 9.

•2- 12downtilt can be achieved by aligning the corresponding hole in the tilt

arm to the pivot bracket which mates against the mounting pole, as shown in

Figure 9. The first hole is for 2downtilt, with each consecutive hole resulting

in an increased inclination of 2.

For typical installations the minimum recommended pipe diameter is 90mm (3.5").

Figure 4.

Figure 5.

Figure 6.

10°Downtilt

5°Downtilt

0°Downtilt

I Installation Instructions-Mechanically Adjustable Downtilt Mounting Kits for

1400 - 1800mm (55.1” – 70.9”) Antenna’s (T-041-GL-E),

Bracket Spacing 976mm (38.4")

www.commscope.com

Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.

All trademarks identified by ® or ™are registered trademarks or trademarks, respectively, of CommScope, Inc. A997-0086 G (5/19)

Page 6 of 8

A997-0086

Figure 7. Lower Mounting Bracket Exploded Assembly.

Figure 8. Upper Mounting Bracket Exploded Assembly.

Figure 9. Upper Bracket Placement For Various Downtilts.

Figure 13: Correctly Assembled Mounting

Bracket for Mechanically Adjustable

Downtilt Antenna

Operation of Antennas

RET Antennas AISG Compliant antennas are compatible with AISG compliant control unit

equipment. For operation of downtilt using AISG compliant controllers see

the controller documentation.

www.commscope.com

Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.

All trademarks identified by ® or ™are registered trademarks or trademarks, respectively, of CommScope, Inc. A997-0086 G (5/19)

Page 7 of 8

A997-0086

1. Use a tether to secure the antenna’s hoisting eye to the mounting structure.

The tether can be a rope, wire rope, chain, or similar material. The tether should

be short enough to prevent the antenna from tilting beyond its maximum downtilt

range. This will prevent the antenna from tilting away from the mounting structure

when the adjusting bolts are removed.

Installed cables or the antenna may be damaged if they are allowed to strike the

mounting structure when the antenna mechanical downtilt is changed.

Figure 15: Upper Mounting Bracket Assembly

2.Loosen the fasteners holding the bottom antenna bracket to the bottom pivot

bracket. Do not remove them.

Figure 16: Lower Mounting Bracket Assembly

ADJUSTING MECHANICAL DOWN TILT AFTER INSTALLATION

F-042-GL-E, T-045-GL-E & T-041-GL-E

Loosen the

Fasteners

www.commscope.com

Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.

All trademarks identified by ® or ™are registered trademarks or trademarks, respectively, of CommScope, Inc. A997-0086 G (5/19)

Page 8 of 8

A997-0086

3. Remove the M12 bolts, washers, and nuts from the pivot bracket. The antenna may

tilt down to the extent allowed by the tether installed in step 1.

Figure 17: Upper Mounting Bracket Assembly

4. The desired downtilt angle may be obtained with the correct adjustment of the tilt

arm bracket. See the installation instructions above for detailed information.

5. Adjust the antenna downtilt to the desired angle and reinstall the M12 bolts,

washers, and nuts between the upper pivot bracket and the tilt arm.

6. Tighten all four M12 nuts to 38Nm (28 ft.lb).

7. Remove the tether.

Remove the

Fasteners

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels CommScope Antenne

CommScope

CommScope CMAX-DM60-Series Manuel utilisateur

CommScope

CommScope CELLMAX-D-CPUSE Manuel utilisateur

CommScope

CommScope ASP7A Manuel utilisateur

CommScope

CommScope CMAX Series Manuel utilisateur

CommScope

CommScope ValuLine VHLP1 Series Manuel utilisateur

CommScope

CommScope DB404 Series Manuel utilisateur

CommScope

CommScope CMAX-DM20 Manuel utilisateur

CommScope

CommScope Argus CVVPX Manuel utilisateur

CommScope

CommScope CMAX-D-43-UW-i53 Manuel utilisateur

CommScope

CommScope CMAX-OUS-UW43-i53 Manuel utilisateur

CommScope

CommScope CMAX-DMF3-43-Ci53 Manuel utilisateur

CommScope

CommScope CMAX Series Manuel utilisateur

CommScope

CommScope MC-MNT-3XV-TS1 Manuel utilisateur

CommScope

CommScope ValuLine VHLP3 Series Manuel utilisateur

CommScope

CommScope DB224 Manuel utilisateur

CommScope

CommScope CMAX-DMF-43-UW-i53 Manuel utilisateur

CommScope

CommScope ValuLine VHLP 3 Series Manuel utilisateur

CommScope

CommScope CMAX Series Manuel utilisateur

CommScope

CommScope Valuline Manuel utilisateur

CommScope

CommScope CMAX-OMF7-43-UWI53 Manuel utilisateur

CommScope

CommScope ValuLine VHLP3 Series Manuel utilisateur

CommScope

CommScope CMAX-OUS-43-i53 Manuel utilisateur

CommScope

CommScope 5NPX1006F Manuel utilisateur

CommScope

CommScope 3X-C70B-3XR Manuel utilisateur

Manuels Antenne populaires d'autres marques

Alfa Network

Alfa Network APA-L01 Manuel utilisateur

Naval

Naval PR-422CA Manuel utilisateur

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuel utilisateur

TERK Technologies

TERK Technologies TV44 Manuel utilisateur

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuel utilisateur

HP J8999A Manuel utilisateur

MobilSat

MobilSat MSP-S Manuel utilisateur

Steren

Steren ANT-UHF 13 Manuel utilisateur

Novatel

Novatel 600-G Manuel d'utilisation

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuel utilisateur

TRENDnet

TRENDnet TEW-AO12O Manuel utilisateur

Radio Shack

Radio Shack 15-1837 Manuel utilisateur

Ramsey Electronics

Ramsey Electronics DAP25 Manuel utilisateur

COBHAM

COBHAM SAILOR 800 VSAT Manuel d'utilisation et d'entretien

Trango Systems

Trango Systems AD900-9 Manuel utilisateur

Steren

Steren ANT-100 Manuel utilisateur

Proxim

Proxim 5054-PA-23 Manuel utilisateur

IWCS

IWCS iriBelt II Guide de configuration