CommScope ARGUS Manuel utilisateur

Argus®

Installation Instructions

296mm Profile Panel Antennas

Bulleti Bulletin D701-0013 • Revision C • November 2014 page 1 of 5

CommScope Infrastructure Academy offers installation training

General

This instruction manual contains all necessary information required to assist in the correct

installation of ARGUS

Panel Antennas of 296mm (11.7”) width to a 75 –115mm (3”-4.5”)

diameter pipe when using the mou

nting kit with clamp bracket. Th

ese antennas can be supplied

with either fixed

electrical beam downtilt (FET), manually adjustable electrical downtilt

(MET) or

AISG

-compatible remotely controlled electrical downtilt (RET). Mechanical downtilt is also

available if required, depending on the type of mounting kit selected.

Following symbols can be found next to text outlining important information.

Please follow the procedure marked with this symbol precisely.

Non

-compliance may lead to damage of the product.

Handy tips when instal

ling product.

Unpacking

Make sure that the antenna and the accessory items listed below are provided and have not been

damaged during transport.

·Antenna

·Mounting kit (mounting kit components for each configuration are shown in Figure

s 2

and 3).

·Hex key 6mm AF (supplied with adjustable downtilt antennas only).

Mounting Kit

Type

850mm –1200mm

(33.5” – 43.3”) Antennas

1200mm –1575mm

(43.3” – 62”) Antennas

1575mm –2700mm

(62” –106.3”) Antennas

Fixed Downtilt

F-042-GL-E

Mechanical

Downtilt

T-045-GL-E T-041-GL-E T-029-GL-E

Tilt range

0°, 2°-10°in 1°steps

0°- 12°in 1°steps

0°- 8°in 1°steps

Mounting

Bracket Spacing

Dim A (Fig 4)

716mm (28.2”) 976mm (38.4”) 1400mm (55.1”)

Table 1: Mounting Kit Part Numbers for Different Antennas

Do not install near power lines. Power lines,

telephone lines, and guy wires look the same.

Assume any wire or line can electrocute you.

Do not install on a wet or windy day or

when lightning or thunder is in the

area.

Do not use metal ladder.

Wear shoes with rubber soles and heels.

Wear protective clothing including a

long-sleeved shirt and rubber gloves.

296mm Profile Panel Antennas Bulletin D701-0013 • Revision C • November 2014 page 2 of 5

Installation Instructions

Ensure a torque spanner is used when tightening fasteners, see the mounting kit

diagrams on the following pages for the correct torque recommendations.

Ensure antenna is installed with the connectors at the bottom.

Installation Instructions –Adjustable Downtilt Mounting Kit

T-029-GL-E, T-041-GL-E, T-045-GL-E

Assemble

mounting kits as per Figure 2 and 3 of this document.

1. Attach the mounting kit assembly to the antenn

a, before trying to clamp the

brackets to the pole.

2. Downtilt angles in 1°

increments can be obtained with the correct adjustment

of the tilt arm bracket.

·D

owntilt can be achieved by aligning the corresponding hole in the tilt

arm to the pivot bracket whic

h mates against the mounting pole, as shown in

Figure 4. The first hole is for 1°downtilt*

, with each consecutive hole

resulting in an increased inclination of 1°.

( *Note for the T-045-GL-E kit the tilt is 0°then 2°- 10°in 1°steps.)

·For finer downtilt angle adjustments the distance in between the

top

and bottom mounting bracket on the pole can be adjusted.

·For 0°downtilt the tilt arm may be stowed as show in Figure 4.

·An inclinometer or

other angular measuring device may be used to

verify downtilt angle as required.

Upper Mounting Bracket Assembly

( To Suit Pipes OD 75-115 mm)

Lower Mounting Bracket Assembly

(To Suit Pipes OD 75-115 mm)

Figure 1: Correctly Assembled Mounting Kit Using Clamp Bracket for Mechanically

Adjustable Downtilt Antenna

Bulletin D701-0013 • Revision C • November 2014 page 3 of 5 296mm Profile Panel Antennas

Figure 2: Exploded Assembly for Upper Mounting Bracket using Clamp Bracket

Figure 3: Exploded Assembly for Lower Mounting Bracket using Clamp Bracket

(This configuration should also be used for the upper Mounting Bracket when 0° tilt is

required)

Figure 4: Typical Example of Upper Bracket Placement for Various Downtilts

OPTIONAL: THE TILT ARM AND EXTRA HARDWARE

CAN

BE STOWED IN THE POSITION SHOWN WHEN

0° DOWNTILT

CONFIGURATION

USING A CLAMP

BRACKET.

296mm Profile Panel Antennas Bulletin D701-0013 • Revision C • November 2014 page 4 of 5

Operation of Antennas

ET Antennas

The beam downtilt is factory set.

MET

Antennas

The beam downtilt below the horizon is adjusted by rotating the hex socket

located at the bottom of the antenna

- Figure 5

). Turning the hex socket in

a clockwise direction increases the beam downtilt below the horizon.

Turning the hex socket in an anti

clockwise direction decreases the beam

downtilt below the horizon. Be

am downtilt setting

in degrees below

boresight

can be read off the scale at the base of the antenna.

The downtilt

setting is read from th

e face of the antenna bottom end cap

at the point

where the scale protrudes.

AISG Compliant

RET

Antennas

AISG Complian

t antennas are compatible with AISG co

mpliant control

unit equipment. For operation of downtilt using AISG compliant controllers

see the controller documentation.

Where manual override of RET control is

provided at the antenna bottom end cap, operation is identical to that

described above for MET antennas.

WARNING:

During downtilt adjustment ensure the hex socket is not

rned past the minimum and maximum positions

as shown on the downtilt

indicator scale. Forcing the hex adjustment beyond this point

may lead to

damage of the downtilt mechanism. Using power drills and electric

screwdrivers to adjust downtilt may also lead to damage of the

downtilt mechanism.

Port and Band

Identification

Each RF and/or AISG port on the antenna is numbered and identified in

accordance with AISG Standard “AIS

G Antenna Port Color Coding”.

Each

pair of ±45° polarized RF ports on the antenna (an array) is

commonly termed a “Band”. Using this terminology,

the band

ID numbers

rise

in step with the port numbers, ie Ba

nd 1 corresponds with Ports 1 & 2,

Band 2 corresponds with Ports 3 & 4 etc.

Ports are numbered starting with RF low frequency band(s) first, followed

by higher frequency band

(s)

. For bands operating at the same RF frequency,

ports associated with arrays at the bottom of the antenna are numbered

before ports associated with arrays at the top.

For remote tilt

antennas, depending on the configuration

of AISG employed

(Single RET or Multi RET)

the antenna will report the bands differently to

the primary controller as follows:

SRET

: For either AISG1.1 or 2.0, a multiband antenna configured as

cascaded SRET

will

report to the primary controller as multiple antennas,

each with a single band. Each band of the antenna will report a different

serial number. For example, a tri band antenna with serial number

60051007 will report to the controller three individual antennas with serial

numbers 600510071, 600510072, 600510073, where the last digit

represents the band of the antenna.

MRET: When using AISG2.0, a multiband antenna will report to the

primary controller as a single antenna with multiple bands. Each band of

the antenna is accessible through the controller.

Bulletin D701-0013 • Revision C • November 2014 page 5 of 5 296mm Profile Panel Antennas

End Cap Layout for Typical Antennas

Figure

Typical

-port (RVVPX

)

with internal bias

tee on Port 1.

Note: The phase of

Band

2 (ports 3 and

and

Band 3 (ports 5

and

) are

situated above

that of

Band 1

(ports 1

and

2).

Tilt adjust and scale

(Band 1)

Tilt adjust and scale

(Band 3)

Tilt adjust and scale

(Band 2)

CommScope

1100 CommScope Place

SE P.O. Box 339, Hickory, NC 28603-

0339

(828) 324

-2200 (800) 982-1708

www.commscope.com/andrew

Customer Service 24 hours

North America: +1

-800-255-1479 (toll free)

Any country: +1

-779-435-6500

email: acicustomersupportcente[email protected]

Notice: CommScope disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices.

Aviso: CommScope no acepta ninguna obligación ni responsabilidad como resultado de prácticas incorrectas o peligrosas de instalación, inspección, mantenimiento o retiro.

Avis : CommScope décline toute responsabilité pour les conséquences de procédures d’installation, d’inspection, d’entretien ou de retrait incorrectes ou dangereuses.

Hinweis: CommScope lehnt jede Haftung oder Verantwortung für Schäden ab, die aufgrund unsachgemäßer Installation, Überprüfung, Wartung oder Demontage auftreten.

Atenção: A CommScope abdica do direito de toda responsabilidade pelos resultados de práticas inadequadas e sem segurança de i

nstalação, inspeção, manutenção ou remoção.

Avvertenza: CommScope declina eventuali responsabilità derivanti dell’esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.

⌘᜿˖CommScope ޜ⭣᰾ሽᯬнᚠ⮦ᡆнᆹޘⲴᆹ㼍ǃ󱁳傇ǃ㏝؞ᡆ᣶ন󰪞֌ᡰሾ㠤Ⲵ󰵭н䋐ԫօ㗙઼䋜ԫ

Table des matières

Autres manuels CommScope Antenne

CommScope

CommScope CMAX-LHM2-30-I53 Manuel utilisateur

CommScope

CommScope CMAX Series Manuel utilisateur

CommScope

CommScope ValuLine VHLP Series Manuel utilisateur

CommScope

CommScope CMAX-O-CPUSEWV53 Manuel utilisateur

CommScope

CommScope Argus CVVPX Manuel utilisateur

CommScope

CommScope CELLMAX-D-CPUSE Manuel utilisateur

CommScope

CommScope CMAX Series Manuel utilisateur

CommScope

CommScope CMAX-OUS-UW43-i53 Manuel utilisateur

CommScope

CommScope ARGUS U Series Manuel utilisateur

CommScope

CommScope DB224 Manuel utilisateur

CommScope

CommScope CMAX-DMF-43-UW-i53 Manuel utilisateur

CommScope

CommScope 3X-C70B-3XR Manuel utilisateur

CommScope

CommScope ValuLine VHLP 3 Series Manuel utilisateur

CommScope

CommScope ValuLine VHLP Series Manuel utilisateur

CommScope

CommScope CMAX Series Manuel utilisateur

CommScope

CommScope DB404 Series Manuel utilisateur

CommScope

CommScope 5UPX0805F Manuel utilisateur

CommScope

CommScope CMAX Series Manuel utilisateur

CommScope

CommScope CMAX-OMF7-43-UWI53 Manuel utilisateur

CommScope

CommScope Valuline Manuel utilisateur

CommScope

CommScope ION-M8P S Manuel utilisateur

CommScope

CommScope ValuLine VHLP3 Series Manuel utilisateur

CommScope

CommScope Cell-Max CMAX-O-TCPUSEWI53 Manuel utilisateur

CommScope

CommScope ValuLine VHLP3 Series Manuel utilisateur

Manuels Antenne populaires d'autres marques

Alfa Network

Alfa Network APA-L01 Manuel utilisateur

Naval

Naval PR-422CA Manuel utilisateur

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuel utilisateur

TERK Technologies

TERK Technologies TV44 Manuel utilisateur

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuel utilisateur

HP J8999A Manuel utilisateur

MobilSat

MobilSat MSP-S Manuel utilisateur

Steren

Steren ANT-UHF 13 Manuel utilisateur

Novatel

Novatel 600-G Manuel d'utilisation

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuel utilisateur

TRENDnet

TRENDnet TEW-AO12O Manuel utilisateur

Radio Shack

Radio Shack 15-1837 Manuel utilisateur

Ramsey Electronics

Ramsey Electronics DAP25 Manuel utilisateur

COBHAM

COBHAM SAILOR 800 VSAT Manuel d'utilisation et d'entretien

Trango Systems

Trango Systems AD900-9 Manuel utilisateur

Steren

Steren ANT-100 Manuel utilisateur

Proxim

Proxim 5054-PA-23 Manuel utilisateur

IWCS

IWCS iriBelt II Guide de configuration