Command access PD15 Manuel utilisateur

Installation Instructions

Read all instructions completely before beginning.

PD15 CVR Exit Device

Step #1

Prepare lock stile.

38-7/8 (987) From Bottom of

Door to Center Point.

Step #2

Install Rod & Case assembly into active stile.

Secure with 2 ea. 8-32 x 1/4 cap screws.

Active Stile

Install spacer per drawing.

Step #3

Install Top & Bottom Strikes.

Secure with 2 ea. 8-3/4(19) self tap screws.

Active Stile

Step #4

Install Trim and Cylinder.

Install one 8-32 pan head screw partially to suit nominal wall thickness of 1/8” or 3/16”

Install pad assembly and rotate clockwise until it locks into position. Install single

8-32 x 1-15/16” screw and tighten.

NOTE:

Use 8-32x5/16 pan head on 1/8” wall thickness

Use 8-32x5/3/8 pan head on 3/16” wall thickness

NOTE: If trim or cylinder are

not being used, skip this step.

Active Stile

Step #5

NOTE: or for heaver wall extrusion

use 8-32 x 1 3/8 SOC HD MS

Panic Attachment.

- Remove front and rear end base covers by releasing 6-32x3/16(5) & 12-24x1-1/4(32) fillister head

screw through chassis and one 8-32x1-1/4 head machine screw, secure inactive end with single

1/4-20x1/2(13) round head machine screw (phil.) with semsthrough inactive base plate.

- Using the wire access hole as a guide, drill a 3/8" hole into the inactive stile to allow for wire

access.

- Proceed by re-installing base cover on each end of panic base.

Step #6

Adjust Top & Bottom Bolts.

Adjust Top & Bottom Bolts allowing for 1/2”(13) of bolt to extend from vertical stile.

Install bolt guides top & bottom with (2) each #10x1/2(13) flat head self-tapping screws.

Depress push bar, top bolt should lock in the retracted (unlocked) position. If locking does not

occur readjust bolts in half turn increments until locking occurs. Verify operation by fully depressing

touch bar to achieve dogging or full retraction of bolts.

Top Bolt Adjustment:

Release top and bottom bolts by depressing trigger on top bolt guide assembly.

Position top bolt 1/2”(13) from top edge of active stile.

Bottom Bolt Adjustment:

Fully depress push bar, retracting top and bottom rods. Adjust bottom bolt per detail “B”

Manual Check:

With top and bottom bolts fully retracted, depress trigger release, rods will then extend to the locked position.

Install trip bracket and adjust set screw so that when door closes, top bolt guide trigger contacts set

screw and allows bolts to extend.

Active Stile

22901 La Palma Ave.

Installation Flow Chart

Yorba Linda, CA 92887

P: 888-6-ACCESS

F: 888-622-2302

www.commandaccess.com

info@commandaccess.com

PWM202 HO Wiring Instructions

Specifications

Operating Voltage:

Input Wires to PWM202HO:

Output Wires from PWM202HO:

Power Supply:

26.5V +/- 15%

Red (+), Black (-)

Yellow (+), Green (-)

PS1N

Wire Run Guidelines:

For best results we recommend that your maximum wire run not exceed the following:

18ga.= 700’ 16ga. = 1000’ 14ga. = 1250’ 12ga. = 1500’.

Note: A longer wire run than the maximum distances listed may result in an increased delay time

and possible solenoid “drop out” due to voltage drop.

Hook up:

The unit comes with an easy plug-in connector that connects to the solenoid and an easy plug-in

connector for the red & black wires that connect to the positive and negative leads from the power

supply (see fig. 1).

Polarization note:

The unit is polarized. In the event the input leads (red & black) are reversed the PWM202HO will

not work. Simply reverse the leads and the unit should function correctly.

red

com

black

yellow

green

PWM202 HO Solenoid

PS1N

Power

Supply

Step #7

Table des matières

Autres manuels Command access Système d'ouverture de porte

Command access

Command access MLRK1-MRK Manuel utilisateur

Command access

Command access MLRK1 Series Manuel utilisateur

Command access

Command access PD25-UL-M Manuel utilisateur

Command access

Command access PD15-UL-M Manuel utilisateur

Command access

Command access SLP-UL-M-KIT Manuel utilisateur

Command access

Command access MLRK1 Series Manuel utilisateur

Command access

Command access PD10-M-RIM Manuel utilisateur

Command access

Command access MLRK1-KAWP Manuel utilisateur

Command access

Command access MLRK1 Series Manuel utilisateur

Command access

Command access PD10-M-RIM Manuel utilisateur

Command access

Command access MLRK1-HAG Manuel utilisateur

Command access

Command access MLRK1 Series Manuel utilisateur

Command access

Command access PD25-M-SVR Manuel utilisateur

Manuels Système d'ouverture de porte populaires d'autres marques

Pamex

Pamex KT-INP35 Manuel utilisateur

Label

Label NEPTIS/LE Manuel utilisateur

Cal-Royal

Cal-Royal N-F77CVR Manuel utilisateur

Scrigno

Scrigno OPEN1000 Manuel utilisateur

TriMark

TriMark UM 34 Manuel utilisateur

BFT

BFT WIND RMB 130B 200 Manuel utilisateur

Alecto

Alecto ADI-250 Manuel utilisateur

Besam

Besam Swingmaster MP Mode d’emploi

CRL

CRL SENIOR PRIMA Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 1431 Series Manuel utilisateur

GAL

GAL MOVFR Fiche technique

Olide

Olide 120B Manuel utilisateur

Normstahl

Normstahl IDO7 Manuel utilisateur

Häfele

Häfele Finetta T 70 VF Manuel utilisateur

AGS

AGS D-PL Manuel

Stanley

Stanley MA900ñ Instructions d'installation

WITTUR

WITTUR Hydra Plus UD300 Manuel

Alutech

Alutech TR-3019-230E-ICU Instructions d'installation et d'utilisation