Command access MLRK1-KAWP Manuel utilisateur
#20638_D
US customer support 1-888-622-2377 | www.commandaccess.com | Canada customer support 1-855-823-3002
1
MLRK1-KAWP
INSERT Instructions
The Command Access MLRK1-KAWP is a eld-installable motorized latch-retraction kit for the
Kit Includes
A. 60417 – MLRK1 motor
B. 50944 - molex pigtail
C. 50030 – 6’ power cable
D. 60708/51186 – MM4T REMOTE MODULE
E. 51198 – Remote Module Cable
F. 40059 – (x2) CABLE MOUNTING PAD
G. 40060 – (x2) CABLE TIES
H. 40306 – PhiLLIPS SCREWS (x4)
Kawneer Paneline series exit devices.
A. B.
F. H.G.E.D.
C.
INSTALLATION VIDEO
REQUIRED COMMAND Power Supplies: Use a PS210/220/440B
All Command Access exit devices & field installable kits have been thoroughly cycle tested with Command Access power
supplies at our factory. If you plan on using a non-Command power supply it must be a filtered & regulated linear power supply.
SPECIFICATIONS
• SPDT - Rated .5a @24V
• green= Common (C)
• Blue = normally open (NO)
• grey = normally closed (NC)
Optional built-in rex
• Input Voltage: 24-25.3VDC
• AVERAGE low Torque LATCH RETRACTION CURRENT: 900 mA
• Average high torque latch retraction current: 2A
• Average holding current: 215 ma
• Wire gauge: Minimum 18 gauge
• Direct wire run - no relays or access control units in-between power supply & module
#20638_D
US customer support 1-888-622-2377 | www.commandaccess.com | Canada customer support 1-855-823-3002
2
REMOVING AND DISASSEMBLING PUSH PAD
INSTRUCTIONS
1Using a at screw driver or putty knife, gently pry at top and bottom on Filler Plater on
each side of device until they come out
#20638_D
US customer support 1-888-622-2377 | www.commandaccess.com | Canada customer support 1-855-823-3002
3
REMOVING AND DISASSEMBLING PUSH PAD
INSTRUCTIONS
2Once exposed remove (4) Philips head mounting screws and remove push pad
from pocket in door
#20638_D
US customer support 1-888-622-2377 | www.commandaccess.com | Canada customer support 1-855-823-3002
4
REMOVING AND DISASSEMBLING PUSH PAD
INSTRUCTIONS
3Remove (4) Philips head screws attaching Push Pad to chassis
#20638_D
US customer support 1-888-622-2377 | www.commandaccess.com | Canada customer support 1-855-823-3002
5
REMOVING AND DISASSEMBLING PUSH PAD
INSTRUCTIONS
4Disassemble Retraction Assembly (1) Bolt with (1) C-Clip, (2) adjustment / set
screws and “L” Piece
#20638_D
US customer support 1-888-622-2377 | www.commandaccess.com | Canada customer support 1-855-823-3002
6
REMOVING AND DISASSEMBLING PUSH PAD
INSTRUCTIONS
5Remove Push Pad from chassis by pulling in opposite directions, if it proves difcult to
separate, a rubber mallot can be used to get it past any stubborn points.
Watch for bearings that may fall out during removal.
#20638_D
US customer support 1-888-622-2377 | www.commandaccess.com | Canada customer support 1-855-823-3002
7
installation instructions
3Flip the Motor Kit over so the underside is facing you, next slide the Head Link of the motor kit through
the Rear Activating Bracket Opening.
Head Link
1With the Push Pad removed, ip it over and locate the Rear Activating Bracket.
2Locate the Opening in the Rear Activating Bracket, this is where the kits head link will slide through.
Opening
Front of Device
#20638_D
US customer support 1-888-622-2377 | www.commandaccess.com | Canada customer support 1-855-823-3002
8
installation instructions
4Fit the Hole on the end of the Head Link over the Rear Post of the Rear Mounting Bracket as shown.
Hole
Post
5Then t the Hole on the Motor Bracket over the Side Post of the Rear Mounting Bracket as shown.
Post
NOTE:
Motor Bracket
Needs to Be
Sitting Flush
with The
Activating
Bracket
Motor Bracket
#20638_D
US customer support 1-888-622-2377 | www.commandaccess.com | Canada customer support 1-855-823-3002
9
installation instructions
Once kit is in place connect 3-Pin and 4 -Pin Connectors on the Remote Module Cable to 3-pin and
4-Pin Connectors from Motor and Sensor. Apply Strain Relief as shown below or to installers best
judgement.
6
8Before re-installing the Push Pad, ensure the bearings are still on the Activating Brackets!
Bearings Bearings
7Guide wire to rear of device and feed through Back Activating Bracket. Ensure nothing is being
pinched or strained by depressing the Back Activating Bracket.
#20638_D
US customer support 1-888-622-2377 | www.commandaccess.com | Canada customer support 1-855-823-3002
10
installation instructions
10 The Two Tabs on the Motor Bracket, Rear Activating Bracket and Bearings must also slide into the
Slots on the Base Rail.
Motor Bracket Tabs Activating Bracket Bearings
WARNING
If this bracket does not
properly slide into channel,
it will create a bind on the
motor assembly
9Re-install the Base Rail, making sure the Front Activating Bracket and Bearings slide into their Slots.
Table des matières
Autres manuels Command access Système d'ouverture de porte
Command access
Command access MLRK1 Series Manuel utilisateur
Command access
Command access PD10-M-RIM Manuel utilisateur
Command access
Command access MLRK1 Series Manuel utilisateur
Command access
Command access PD25-M-SVR Manuel utilisateur
Command access
Command access PD10-M-RIM Manuel utilisateur
Command access
Command access PD15 Manuel utilisateur
Command access
Command access MLRK1 Series Manuel utilisateur
Command access
Command access MLRK1 Series Manuel utilisateur
Command access
Command access SLP-UL-M-KIT Manuel utilisateur
Command access
Command access MLRK1-HAG Manuel utilisateur
