Comm-Tec CTG-KNX/IP Manuel utilisateur
CT-KNX Gateway Protocol
Quickstart
COMM-TEC GMBH SIEMENSSTRASSE 14 TELEFON 07161/30 00-0 WWW.COMM-TEC.DE
D-73066 UHINGEN TELEFAX 07161/30 00-400
1
/
2
Th s s a qu ckstart gu de for programm ng the CTG-KNX/IP or CTG-EIB/NX ava lable at
www.comm-tec.de.
Both dev ces have the same protocol, but d fferent nterfaces.
Notes:
•The CTG-KNX/IP allows only one s multaneous IP connect on, th s means hav ng
the controller and a software s multaneous connected does not work.
•The gateway has a bu ld n f lter table. Only group addresses wh ch are l sted n
th s f lter can pass the gateway, everyth ng else w ll be deleted!!(see page 2 of
th s document)
•The f ltertable can’t be retr eved from the gateway.
Commun cat on parameters:
CTG
-
EIB/NX
CTG
-
KNX/IP
Baudrate:
38400 8N1
Use a stra ght cable (p n 2, 3 & 5)
Port
:
10002
Frameformat: <STX><command><ETX>
<STX> = 02 hex ( 0x02 )
<ETX> = 03 hex ( 0x03 )
<command> = ASCII commands
Commands:
uppercase W s for Wr t ng
uppercase R s for Read ng
Sam les:
0x02W10/5/7=10x03 Wr tes the value 1 to the group address 10/5/7
0x02W1/65/77=1000x03 Wr tes the value 100 to the group address 10/65/77
0x02R10/5/70x03 Request the value of the group address 10/5/7
Feedback:
Cylic data, confirmation of a send command(only Echo, if it is turned on)
A>10/5/7=1
When doing readrequests:
A@10/5/70=192
When EIB-Bus is busy:
Try to read 3 times
B@01/0/203 You can make a message bus is busy, but it is useless.
-@01/0/203 no answer massive EIB Problems, call the EIB technician
CT-KNX Gateway Protocol
Quickstart
COMM-TEC GMBH SIEMENSSTRASSE 14 TELEFON 07161/30 00-0 WWW.COMM-TEC.DE
D-73066 UHINGEN TELEFAX 07161/30 00-400
2
/
2
Sett ng the F ltertable and commun cat on w th the gateway
a) First set the Interface parameter
b) Press the Green arrow for connecting to the
Gateway
c) type a ? and <Return> in the text field here. If
you are connected you get a list of commands
from the gateway, which shows everything is
working properly.
d) You can test the commands from the first page
for reading and writing here
Setting the Filtertable
Set the option for Echo (1)
Press the transmitt button (6)
Enter the group adress you want to read or
programm in the fiels (2)
Choose the correct Datatype of the variable(3)
Press the button (4) for accepting your selection
Repeat the last 3 steps until all your needed
adresses are entered
If you have entered all needed adresses send
them to the gateway by pressing button (5)
For later use save the content of the filtertable in
a textsheet (7). This is optional not needed
NOTE:
If your Media control system is reconfiguring the
filtertable by itself. You do not need to manually set
the filtertable.
Sample
What you need from a EIB/KNX programmer to set up your Gateway:
Address Type Description Parameters Read or write
1 / 4 / 100 1 Bit Lamp 1 0 – off 1- on write
1 / 1 / 103 4 Bit Lamp 1 Dimmer write
1 / 4 / 102 1 Byte Lamp 1 get value
absolut 0-255 read
1 / 4 / 101 1 Byte Lamp 1 set value
absolut 0 - 255 write
a
b
c
Ce manuel convient aux modèles suivants
2
Autres manuels Comm-Tec Porte
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
