Code Alarm CATX610 Mode d'emploi

Model CATX610

Programming Guide

The keychain transmitters included with the system have been pre-

programmed at the factory, with each button pre-assigned to control a specific

function of the system.

The system will store codes from up to 4 different transmitters. If a 5th

transmitter is programmed to the system, then the first transmitter

programmed to the system will be erased from the system’s memory.

To program new or additional transmitters:

1. Enter the vehicle, and turn the ignition switch to the ON position.

2. Press and release the programming button switch 3 times.

3. The dash mounted LED will flash 1 time, and the horn/siren will sound 1

time, indicating that the system is ready to accept programming of channel 1

which is arm/lock.

4. Press and hold the lock icon button of the transmitter you wish to program

for 4 seconds or until a long chirp is heard from the horn/siren.

4a. Repeat step 4 for any additional transmitter you wish to program.

5. Press and release the programming button switch 1 time to advance to

channel 2. The dash mounted LED will flash 2 times and the orn/siren will

sound 2 times, indicating that the system is ready to accept programming for

channel 2 which is disarm/unlock.

6. Press and hold the unlock icon button of the transmitter you wish to

program for 4 seconds or until a long chirp is heard from the horn/siren.

6a. Repeat step 6 for any additional transmitter you wish to program.

7. Press and release the programming button switch 1 time to advance to

channel 3. The dash mounted LED will flash 3 times and the horn/siren will

sound 3 times, indicating that the system is ready to accept programming for

channel 3 which is trunk release/remote start.

8. Press and hold the trunk/key icon button of the transmitter you wish to

program for 4 seconds or until a long flash from the parking lights.

8a. Repeat step 8 for any additional transmitter you wish to program.

9. Press and release the programming button switch 1 time to advance to

channel 3. The dash mounted LED will flash 4 times and the horn/siren will

sound 4 times, indicating that the system is ready to accept programming for

channel 4 which is an optional device.

10. Press and hold the option button of the transmitter you wish to program

for 4 seconds or until a long flash from the parking lights.

10a. Repeat step 10 for any additional transmitter you wish to

program.

Changing the Remote Control Battery

The 12-volt alkaline battery supplied in your remote

transmitter should last approximately one year, depending on

usage. When the battery begins to weaken, you will notice a

decrease in range, or the distance from your vehicle that

your remote transmitter will operate. Follow the instructions

below to change the remote transmitter battery.

For Customer Service and Product information Call

1-800-421-3209

1. Insert the edge of a coin into the slot at the side of the

remote control. Twist the coin to pry the remote control

halves apart.

2. Remove the old battery and replace with a new one.

Be sure to observe the (+) and (-) signs in the battery

compartment.

3. Carefully snap the case halves back together, then test

the remote control.

Model CATX610

Programming Guide

Table des matières

Autres manuels Code Alarm Alarme de voiture

Code Alarm

Code Alarm CA 680 Manuel utilisateur

Code Alarm

Code Alarm CA 521 Manuel utilisateur

Code Alarm

Code Alarm Professional 1000 Manuel utilisateur

Code Alarm

Code Alarm CA 671 Manuel utilisateur

Code Alarm

Code Alarm 420A Manuel utilisateur

Code Alarm

Code Alarm CATX520 Mode d'emploi

Code Alarm

Code Alarm CA 170 Manuel utilisateur

Code Alarm

Code Alarm PowerCode PC 7300 Manuel utilisateur

Code Alarm

Code Alarm ca 2051 Manuel utilisateur

Code Alarm

Code Alarm CA 180 Manuel utilisateur

Code Alarm

Code Alarm 2000 Manuel utilisateur

Code Alarm

Code Alarm UTXPR Manuel du propriétaire

Code Alarm

Code Alarm CATX2LCD Mode d'emploi

Code Alarm

Code Alarm CA 110 Manuel utilisateur

Code Alarm

Code Alarm F50 Manuel utilisateur

Code Alarm

Code Alarm ELITE Series Manuel utilisateur

Code Alarm

Code Alarm CATX2LED Mode d'emploi

Code Alarm

Code Alarm CA 210 Manuel utilisateur

Code Alarm

Code Alarm CA 420 Manuel utilisateur

Code Alarm

Code Alarm CA-130 Manuel utilisateur

Code Alarm

Code Alarm CA-120 Manuel utilisateur

Code Alarm

Code Alarm 2000 Manuel utilisateur

Code Alarm

Code Alarm CA-330 Manuel utilisateur

Code Alarm

Code Alarm CA 170 Manuel utilisateur

Manuels Alarme de voiture populaires d'autres marques

Clifford

Clifford 3606X Manuel utilisateur

Ultra Start

Ultra Start 2500M SERIES Manuel utilisateur

Ultra Start

Ultra Start 650 Series Manuel utilisateur

Audiovox

Audiovox Prestige Platinum+ APS-511C Manuel utilisateur

Sparkrite

Sparkrite SRA8 Manuel utilisateur

Viper

Viper 4708V Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manuel

Falcon

Falcon Predator XL3 Guide de l'utilisateur

Audiovox

Audiovox Auto Security XR91 Mode d'emploi

Clifford

Clifford Sabre II Manuel utilisateur

CrimeStopper

CrimeStopper CS-8717 Guide de démarrage rapide

Ultra Start

Ultra Start 450 SERIES Manuel utilisateur

Scytek electronic

Scytek electronic Vectra X3 Manuel utilisateur

Excalibur

Excalibur AL-1860-EDPB Manuel utilisateur

Clifford

Clifford CYBER 2 Manuel utilisateur

Gemini

Gemini 7057 Manuel utilisateur

FlashLogic

FlashLogic FLRSBA PRESTIGE Manuel utilisateur

Magicar

Magicar FAI-440 Manuel utilisateur