Clevertronics TS EUBPRO-LI Instructions d'installation et d'utilisation

1943063

V1.1

12 January 2022

Instruction Sheet Template - V1.2 –Updated 06/10/2021

THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK

Trade Series Ultrablade Pro LED Exit

Installation & Maintenance Instruction Leaflet

Victoria (Head Office & Manufacturing)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9207 0000

Fax: +61 8 9207 0088

New Zealand

Phone: +64 800 548 448

Designed in Australia to comply with the requirements of

AS2293.3: 2005 and AS/NZS CISPR15: 2017

Models:

EUBPRO-LI

Spare Parts:

1560200

Battery, 3.2 Volt 1.1Ah Li-ion

8002179

PCA:EUBPRO LED Strip Assy (CT10602-x)

2740054

Ultrablade to Ultrablade Pro adapter

AUM03570010001

EUBPRO-CKIT-LI Ultrablade Pro,Control Only, Eco Li, M/NM

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

1943063

V1.1

12 January 2022

Instruction Sheet Template - V1.2 –Updated 06/10/2021

Installation:

The Trade Series Ultrablade Pro LED Exit (EUBPRO-LI) is a recessed ceiling mount fitting. TheEUBPRO-

LI can be attached directly to any solid surface, or to a ceiling tile with the integrated clamping

mechanisms. The EUBPRO-LI comes with an attached Flex and Plug. Please follow the steps below to

install the EUBPRO-LI Exit:

•If replacing an Ultrablade, an Ultrablade to Ultrablade Pro adapter 2740054 (sold separately)

is required)

•Create a cut-out (350mm x 48mm) in the mounting surface.

•Route the power cord to the mains connection and connect the 240VAC supply.

•Insert the EUBPRO-LI into the ceiling cavity tighten the (4) clamping screws.

•Alternately, fix the EUBPRO-LI to a solid surface using (4) screws through the surface material.

•Install the cover plate.

•Apply power to the fitting and test.

Ceiling Tile

Clamping Screws

Cover Plate

Clamping Screws

Solid surface screw points

Maintained/Non-Maintained Operating Mode:

Press the Test Button 5 times within a 4 second period to toggle operation of the fitting between

Maintained and Non-Maintained mode

Changing EXIT Legend Inserts:

The Ultrablade Pro Exit comes with an assortment of standard legends.

1. To remove the legend, grasp the centre of the bottom trim piece and pull down slightly to

expose the legend edge. See photo.

2. Grasp the bottom edge of the legend and slide the existing legend out of the blade, while

working the edges out along the sides.

3. Slide the new legend into the blade, ensuring to fit the edges into the sides then slide the

legend to the top of the blade. Insert one bottom corner then the other. Slide the legend down

into the bottom trim.

Pull the trim out and Lift the decal and Insert corners (1&2) Insert corners (4&5), then

the centre slide out then slide up (3) slide down

Testing:

Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24 hours.

Conduct the following tests:

•For the first test, the emergency lamp must remain illuminated for at least 2 hours after disconnection

from the mains supply.

•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are required

to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails to remain

illuminated for the requisite time, remedial action must be taken to repair the situation and once

completed, the unit must pass a subsequent test. For more specific information, please refer to the

current edition of the AS 2293.3 Standard.

Ultrablade Maintenance:

LED Lamp Replacement:

•Use only the LED Strip recommended in the

Spares Parts list of this instruction.

•Disconnect battery from LED driver.

•Remove the screw holding the driver PCA.

Remove the PCA.

•Remove the 4 screws holding the battery

bracket. Remove the bracket with the battery.

•Disconnect the signal cable from LED strip.

•Remove 4 self-tapping screws and unclip the

LED strip.

•Install the new LED strip following the above

procedure in reverse.

Battery Replacement:

•Use only the battery recommended in the

Spares List on this instruction.

•Remove the battery from battery

compartment, un-plug the lead from the

battery connector remove the old battery.

•Plug the new battery into the battery

connector.

•Secure the battery into the battery

compartment

Trouble Shooting:

Below are a list of common problems and their

possible causes.

Fault: The Green LED Test Switch

indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in

emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency

mode, but only stays on for a short

period.

Check: Battery has been allowed to charge for

at least 24 hours.

Battery for damage.

Fault: Green LED flashes once every 5

seconds-Battery is disconnected

Check: Battery is connected.

Fault: Green LED blinks off once every 5

seconds- Charging very flat battery

Allow 20min to recover battery then

recheck

Fault: Green LED flashes at 2Hz (Fast

flash)- Faulty battery

Replace battery

Rated Emergency Lumen Output in accordance with AS2293.1, not applicable for –TH

(theatre) version (refer to spacing tables for installation positions):

Refer to the Technical Label for classification information.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during construction. As a

result, any Exit & Emergency Units, on these circuits, will have their batteries discharged or “cycled”. The battery in this

fitting has been selected to give excellent long-life performance in a controlled AS2293 testing environment. Excessive

battery cycling will reduce through-life performance and may lead to premature battery failure. Battery warranty claims,

as a result of such abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Luminaire Dimensions: 380mm x 220mm

Cover Plate: 385mm x 67mm

Ceiling Cut-out: 350mm x 48mm

Minimum Depth 80mm

Autres manuels Clevertronics Équipement d'éclairage

Clevertronics

Clevertronics L10 LJWELED-40 Series Manuel utilisateur

Clevertronics

Clevertronics CleverEVAC L10 Cleverfit Pro DYRL CP Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LUBPRO Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LIFELIGHT PRO Instructions d'installation et d'utilisation

Clevertronics

Clevertronics CBULKy Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP CUBPRO Series Manuel utilisateur

Clevertronics

Clevertronics LP Argonaut PLUS Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP Ultrablade Pro CUBPRO Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 Cleverfit Pro LCFPRO-TH Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics GLIDER-SM Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 Supalite LFLLED Series Manuel utilisateur

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE PRO Series Manuel utilisateur

Clevertronics

Clevertronics Glider Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LBLLED-REC-WM Series Caractéristiques techniques

Clevertronics

Clevertronics L10 Ultrablade Pro LUBPRO-SM Series Mode d’emploi

Clevertronics

Clevertronics L10 Cleverfit LCFLED Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP Cleverfit CCFLED Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LIFELIGHT-2PRO-SMS-600 Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LVP2LEDM-P Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics TS Trade Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LBS2N Series Mode d’emploi

Clevertronics

Clevertronics CleverEVAC L10 UltraBlade Pro Dynamic Red Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 Cleverfit Pro Instructions d'installation et d'utilisation

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur