Clarke MSP12 Manuel utilisateur

SUBMERSIBLE TRANSFER PUMP

Model No: MSP12

Part No: 7260040

Thank you for purchasing this Clarke Mini Submersible Pump.

Please read this leaflet thoroughly before use to ensure you are fully aware of the limitations

and methods of use and of all safety precautions that must be taken into consideration.

This will also ensure that with proper use, the pump will provide you with many years of

satisfactory service.

Guarantee

This CLARKE product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered

with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be

returned to us without prior permission.

This guarantee does not effect your statutory rights.

Please check the contents to ensure they are complete and that no transit damage has

occurred.

Should any damage be apparent, please contact your Clarke dealer immediately

When disposing of this product, do not dispose of with general waste. It must be disposed of according to the laws

governing Waste Electrical and Electronic equipment, at a recognised disposal facility.

Contents

• 1 pump c/w 4m supply cable with crocodile clips

• 3m flexible hose

• 2 x 15mm jubilee clips

• 15mm steel tube x 150mm length

Safety Precautions

This pump is ONLY for use with the following:

• Clean water or water with small solids in suspension (dirty water).

• Diesel fuel

• Paraffin

DO NOT use this pump for pumping:

• Slurry

• Sceptic Tanks

• Sandy water

• WARNING: DO NOT USE FOR PUMPING PETROL

•ALWAYS disconnect the pump from the power supply before performing any

maintenance operations.

•ALWAYS check the power input cable before use to ensure it is perfectly serviceable.

•ALWAYS ensure the filter is clean and perfectly serviceable before use.

•NEVER run the pump dry. Minimum water depth is 30mm

•DO NOT exceed the duty cycle - see Specifications.

•DO NOT use if any part appears to be damaged. Have it repaired by your Clarke dealer.

•DO NOT use the pump for any purpose other than that for which it is intended.

•DO NOT operate the pump continuously - eg. in a fish pond or collection tank, water

feature etc.

•DO NOT use or leave the pump in freezing conditions.

•DO NOT allow uncontrolled discharge of

contaminated

water etc. ALWAYS collect in

a container and dispose of according to all H & S regulations and local laws.

Specifications

Flow Rate ..................................................... 16.5 litres/min

Min. Water Depth ...................................... 30mm

Voltage ........................................................ 12V

Current ......................................................... 4.5A DC

Pressure ........................................................ 15psi / 1 bar

Height .......................................................... 145mm

Diameter ...................................................... 53.5mm

Weight .......................................................... 0.6kg

Duty cycle ................................................... 15mins continuous in any

30 min period

Limitations of Use

Method of Operation

1. Always check to ensure the pump is in perfect working order:

- has no apparent damage

- the filter is in place and perfectly clean

- the power cable is in perfect condition

2. Attach the flexible hose to the outlet, securing with the jubilee clip supplied.

3. If required, attach the stainless steel tube to the discharge end of the flexible hose,

securing with the jubilee clip supplied.

4. Carefully lower the pump into the pit or sump etc., to be drained.

IMPORTANT, if the bottom of the pit or sump is muddy or sandy, support the pump on a

brick or something similar. DO NOT allow it to rest in the mud or sand.

5. Connect the clamps to the 12Volt battery and the pump will operate.

IMPORTANT: ALWAYS connect the red - positive clamp to the red positive terminal of the

battery FIRST, then connect the black clamp to the black - negative terminal, ensuring both

clamps are perfectly secure.

When disconnecting - ALWAYS disconnect the black - negative clamp FIRST.

Always observe the pump discharge. Should it deteriorate during use, it is probable that the

filter is becoming blocked. In this case, disconnect the pump from the battery - black terminal

first, then carefully withdraw the pump from the pit or sump etc. DO NOT yank the cable.

Unscrew the base cap and remove the filter. Either clean thoroughly or replace as necessary,

then check the impeller to ensure it is free to rotate and is not blocked.

When satisfied, replace pump in sump or pit etc., and proceed to pump once more.

When finished, ALWAYS remove the filter and clean it thoroughly, then allow it to dry.

Thoroughly clean the pump with clean water and ensure the impeller is completely free

to rotate and is free of any contaminants.

Reassemble the pump and store in a clean, dry environment.

Parts and Service

The following parts are available from your Clarke dealer:

1. End Cap Part No: MSP1201

2. Filter MSP1202

3. Cable Clamp - Red MSP1203

4. Cable Clamp - Black MSP1204

5. Flexible Hose - 4M MSP1205

For Spare Parts and Service, please contact your nearest dealer,

or CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: 020 8988 7400

PARTS & SERVICE FAX: 020 8558 3622

or e-mail as follows:

PARTS: [email protected]

SERVICE: [email protected]

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Clarke Pompe à eau

Clarke

Clarke CHHDP830 Mode d’emploi

Clarke

Clarke CPE30A3 Mode d’emploi

Clarke

Clarke IVP14A Mode d’emploi

Clarke

Clarke PW2 Manuel d'installation et d'exploitation

Clarke

Clarke DW50 Mode d’emploi

Clarke

Clarke LEP1A 7260060 Mode d’emploi

Clarke

Clarke BIP1500 Mode d’emploi

Clarke

Clarke Hippo4A Mode d’emploi

Clarke

Clarke CS85S Manuel d'installation et d'exploitation

Clarke

Clarke CFT230 Manuel

Clarke

Clarke CPE15A1 Mode d’emploi

Clarke

Clarke PW50A Mode d’emploi

Clarke

Clarke CFTP12 Mode d’emploi

Clarke

Clarke CPPRSS Manuel utilisateur

Clarke

Clarke CWP200 Mode d’emploi

Clarke

Clarke SPE800 Mode d’emploi

Clarke

Clarke HSEC651A Mode d’emploi

Clarke

Clarke HSE120 Manuel d'installation et d'exploitation

Clarke

Clarke STP12 Mode d’emploi

Clarke

Clarke TAM101 Manuel d'installation et d'exploitation

Clarke

Clarke PSP105 Mode d’emploi

Clarke

Clarke CPCDP500 Mode d’emploi

Clarke

Clarke CBM250SS Mode d’emploi

Clarke

Clarke PTP100 Mode d’emploi

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur