Clarke CPS125 Manuel utilisateur

METAL SHEARS

Model Nos:

CPS125, CPS150 & CPS200

Thank you for purchasing these CLARKE Metal Shears.

Please read this leaflet thoroughly and follow the instructions carefully, in doing so

you will ensure the safety of yourself and that of others around you, and you can

look forward to the tool giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered

with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be

returned to us without prior permission.

This guarantee does not effect your statutory rights.

SAFETY PRECAUTIONS

As with all tools and workshop equipment, it is necessary to exercise caution when

they are put to use. Be aware of the inherent dangers associated with their use.

• Ensure the tool is firmly bolted down.

• ALWAYS keep hands and fingers well away from the cutting blades.

• ALWAYS wear suitable safety goggles when using the tool to prevent against

the possibility of damage from flying splinters.

• Round stock should be cut using the hole provided in the cutting blade ONLY.

• The tool is designed for cutting low carbon (mild) steel only. The attempted cutting

of tool steels, high carbon or alloyed steels will damage the cutting blades.

• ALWAYS keep the cutting Blades sharp and free from burrs or other damage.

• DO NOT exceed the maximum size for cutting...see ‘Specifications’.

• DO NOT use an extension to the lever. If hand leverage cannot cut the

metal, then the work is either too large or it is of the wrong material.

ASSEMBLY

Attach the handle securely, using the two screws provided.

Mount the tool on a sturdy workbench at a height which allows easy operation,

taking into account the general nature of the work expected to be carried out. It

is also possible for the tool to be floor mounted, again, depending upon the work

expected to be carried out.

The tool must be secure. If floor mounted, ensure it is positioned so that it will not

cause an obstruction when not in use. It should be adequately marked to avoid the

possibility of individuals, or traffic etc., inadvertently coming into contact with it.

SPECIFICATIONS

CPS125 CPS150 CPS200

Shear Size ........................................... 127mm (5”) .. 152mm (6”) .. 203mm (8”)

Cutting Capacity . Sheet Metal ...... 2mm ............. 3mm .............. 4mm

Round bar ......... 8mm dia. ...... 8mm dia. ...... 12mm dia.

Part No. ............................................... 1700250 ........ 17002555 ....... 1700260

OPERATION

Position the stock piece between the cutting blades, from the left hand side,

ensuring the ‘kick back’ lever is in place, and directly above the stock. Pull the

lever to cut the desired length, holding the stock piece firmly.

Round stock should ALWAYS be inserted through the hole in the upper cutting Blade.

Ce manuel convient aux modèles suivants

2

Table des matières

Autres manuels Clarke Outils électriques

Clarke

Clarke CAT113 Guide d'installation

Clarke

Clarke Air TPG30PTC Manuel utilisateur

Clarke

Clarke X-PRO CAT140 Manuel d'installation et d'exploitation

Clarke

Clarke Metalworker CDP301B Manuel d'installation et d'exploitation

Clarke

Clarke Strong-Arm CSA15F Manuel d'installation et d'exploitation

Clarke

Clarke CBS16 Mode d’emploi

Clarke

Clarke CONTRACTOR CON1450WC Guide de dépannage

Clarke

Clarke X-Pro CAT202 Manuel d'installation et d'exploitation

Clarke

Clarke CTC150 Mode d’emploi

Clarke

Clarke CAT171 Manuel utilisateur

Clarke

Clarke CAT141 Manuel d'installation et d'exploitation

Clarke

Clarke PRO235 Manuel d'installation et d'exploitation

Clarke

Clarke METALWAORKER CDP502F Mode d’emploi

Clarke

Clarke Strong-Arm CSA20F Mode d’emploi

Clarke

Clarke Strong-Arm CSA50FPB Mode d’emploi

Clarke

Clarke CIR450B Manuel d'installation et d'exploitation

Clarke

Clarke MetalWorker CDP151B Manuel d'installation et d'exploitation

Clarke

Clarke CSG1C Mode d’emploi

Clarke

Clarke Air CAT232 Manuel d'installation et d'exploitation

Clarke

Clarke METALWORKER CBS20 Manuel utilisateur

Clarke

Clarke X-Pro CAT213 Manuel d'installation et d'exploitation

Clarke

Clarke Woodworker CPT600 Manuel d'installation et d'exploitation

Clarke

Clarke CTILG 5060287 Instructions d'installation

Clarke

Clarke CEW1000 Manuel

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel