Clarke CDS1 Manuel utilisateur
USER INSTRUCTIONS
ORIGINAL INSTRUCTIONS DL1223 - Rev1
DRILL STAND
MODEL NO: CDS1
PART NO: 6500220
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
INTRODUCTION
Thank you for purchasing this CLARKE product. Before attempting to use this
product, please read these instructions carefully. In doing so you will ensure
your safety and you can look forward to your purchase giving you long and
satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for its intended purpose. Faulty goods
should be returned to their place of purchase, no product can be returned to
us without prior permission. This guarantee does not effect your statutory rights.
ENVIRONMENTAL PROTECTION
Do not dispose of this product with general household waste. Any tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of appropriately.
SPECIFICATIONS
Dimensions (D x W x H) 410mm x 170mm x 540mm
Base Dimensions (D x W) 160mm x 160mm
Weight 7kg
Maximum Drilling Depth 70mm (2.75inch)
Column to Drill Centre 140mm (5.5inch)
Column Height 550mm (22inch)
Drill Type Suits all drills with standard 43mm neck
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SAFETY PRECAUTIONS
ALWAYS take care that your hands or clothing DO NOT come into contact with
the chuck of the drill. Beware of wearing loose clothing & ensure cuffs are
secured.
ALWAYS learn the applications, limitations and potential hazards relating to the
tool you are using. Read and become familiar with all operating instructions.
ALWAYS wear safety goggles manufactured to the latest European Safety
Standards when drilling. Everyday eyeglasses DO NOT have impact resistant
lenses and are NOT safety glasses.
ALWAYS check for damage before use to ensure that the tool will operate
properly. If in doubt, do not use. Consult your local dealer. Any damage
should be properly repaired or the part replaced.
ALWAYS check for alignment of moving parts and any condition that may
affect operation.
ALWAYS keep work area clean. Cluttered areas invite accidents.
ALWAYS ensure that adequate lighting is available and that you will not be
working in your own shadow.
ALWAYS concentrate on the job in hand, no matter how trivial it may seem. Be
aware that accidents are caused by carelessness.
ASSEMBLY & USER INSTRUCTIONS
1. Insert the steel column ‘A’ into the base and tighten the two fixing screws.
2. Attach the leverage arm in the two places with a bolt ‘B’ and washer, and
knob ‘C’ and washer as shown. IMPORTANT: Note that the knob ‘C’ has a
longer thread than knobs ‘E’ & ‘F’.
3. Insert the depth rod ‘D’ into its hole and hold in the required position by
screwing in the knob ‘E’.
4. Attach the knob ‘F’ to the collar ‘G’ (this will hold your drill in place when
tightened).
5. Slide the depth rule into the slot provided on the left side behind the collar,
nd line up so that the pointer points to zero.
CAUTION: NEVER USE WITH A DRILL IN ‘HAMMER’ MODE.
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
6. To adjust the collar ‘G’ to the required height on the steel column, slacken
the knob ‘C’ and move collar and then re-tighten knob ‘C’ to secure.
7. The drill stand is ready to use. Insert your drill in the collar and tighten knob
‘F’.
8. Once stand is set up and ready for use, the drill bit in your drill should move
down towards the centre of the indent in the base ‘H’. If it is out of line,
slacken knob ‘C’ and readjust collar.
9. We recommend that this drill stand is secured to your workbench using the
four mounting holes ‘J’ in the base.
10. Drill manufacturers safety warnings must be followed before commencing
any work.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Clarke Percer
Clarke
Clarke CHD820 Mode d’emploi
Clarke
Clarke Contractor CON1500RDV Mode d’emploi
Clarke
Clarke CHD850B Mode d’emploi
Clarke
Clarke CAT123 Mode d’emploi
Clarke
Clarke CAT87 Manuel d'installation et d'exploitation
Clarke
Clarke CONRHD720 Mode d’emploi
Clarke
Clarke CON18LI Mode d’emploi
Clarke
Clarke CDS2 Manuel
Clarke
Clarke CAT116 Mode d’emploi
Clarke
Clarke CAT27B Manuel d'installation et d'exploitation
Clarke
Clarke CONTRACTOR CON400RHD Mode d’emploi
Clarke
Clarke Air CAT107 Mode d’emploi
Clarke
Clarke CMD300 Mode d’emploi
Clarke
Clarke X-pro CAT158 Manuel d'installation et d'exploitation
Clarke
Clarke CAT60 Manuel d'installation et d'exploitation
Clarke
Clarke CAT100 Manuel d'installation et d'exploitation
Clarke
Clarke RAD1 Manuel utilisateur
Clarke
Clarke Metalworker CMD10 Manuel
Clarke
Clarke CONTRACTOR CON720RHD Mode d’emploi
Clarke
Clarke Air CAT214 Manuel d'installation et d'exploitation
