Clarke CHT746 Mode d’emploi
OPERATION & MAINTENANCE
INSTRUCTIONS
LS0913
TELESCOPIC SPRING COMPRESSOR
MODEL NO: CHT746
PART NO: 1801746
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
INTRODUCTION
Thank you for purchasing this CLARKE Telescopic Spring Compressor. Designed
for use on wishbone suspension using access points in the rear suspension arm.
features two pairs of carefully shaped yokes that prevent the coil spring from
bowing
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you can look forward to your
purchase giving you long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
WHAT IS SUPPLIED
Contact your Clarke dealer if any items are missing or damaged.
TECHNICAL SPECIFICATION
• 1 x drive handle • 2 pairs of compression yokes
Maximum Spring Load 1250 kg
Size/Suitability Ø 80-135 mm
Opening Range 115 - 300 mm
Weight 6.5 kg
Drive 19 mm Hex
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SAFETY INSTRUCTIONS
•DO NOT operate the spring compressor if parts are damaged or
missing as this can cause failure or injury.
•DO NOT force the spring compressor to achieve a task it was not
designed to perform.
• DO NOT USE AIR TOOLS TO ADJUST THE SPRING COMPRESSOR.
•DO NOT allow untrained persons to use the spring compressor.
• Familiarise yourself with the applications, limitations and potential
hazards of the spring compressor.
• Maintain the spring compressor in good condition. Replace or repair
damaged parts. Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
• Keep the work area clean, uncluttered and ensure there is adequate
lighting.
• Keep hands and body clear of the spring when operating the spring
compressor.
• Maintain correct balance and footing. Ensure the floor is not slippery
and wear non-slip shoes.
• Remove ill fitting clothes. Remove ties, watches, rings, other loose
jewellery. Contain and/or tie back long hair.
• Wear appropriate protective clothing.
• When not in use, clean and store the spring compressor in a safe, dry,
childproof location.
• Do not exceed the maximum capacity of this spring compressor
(1250 kg), if in doubt contact the vehicle manufacturer.
WARNING: ENSURE HEALTH & SAFETY, LOCAL AUTHORITY, AND
GENERAL WORKSHOP PRACTICE REGULATIONS ARE
ADHERED TO WHEN USING THIS EQUIPMENT.
WARNING: WEAR APPROVED SAFETY EYE PROTECTION (STANDARD
SPECTACLES ARE NOT ADEQUATE).
WARNING: DO NOT COMPRESS THE SPRING TO AN EXTENT WHERE THE
COIL WINDINGS OR YOKES TOUCH.
WARNING: MEASURE THE OUTSIDE DIAMETER OF THE SPRING TO BE
COMPRESSED AND SELECT THE CORRECT SET OF YOKES TO
FIT THE SPRING.
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
INSTRUCTIONS FOR USE
IMPORTANT: Do not use the coil spring compressor fully extended, but
adjusted to a length of approx. 200 mm. This will allow adequate travel to
expand and compress the spring.
1. Raise the vehicle to allow access to the spring.
• Make sure that the vehicle is safely and correctly supported.
2. Put the yoke (A) into the lower
part of the spring windings.
3. Insert yoke (B) into the upper part
of the spring windings.
• Make sure that the spring
windings sit between the inner
and outer rims of the yoke.
4. Insert the body of the spring
compressor up through the spring.
• The hexagonal drive nut must
be facing downwards.
5. Guide the compressor through
the lower yoke (A) and up into the
upper yoke (B),
6. When the compressor has passed
through the upper yoke turn the
body through approx 50° so it
locates in the locking grooves on
the yoke as shown.
• Make sure that the spring is
correctly placed within both
yokes and yokes are correctly
aligned with the compressor
body.
WARNING: MEASURE THE OUTER DIAMETER OF THE SPRING TO BE
COMPRESSED AND SELECT THE CORRECT SET OF YOKES.
WARNING: ENSURE THAT THE COIL SPRING TO BE COMPRESSED IS FREE
FROM DIRT AND GREASE WHERE THE YOKES WILL BE IN CONTACT WITH IT
5
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
7. Use a 19mm hex socket to turn the hexagonal drive nut until the yokes are
firmly in contact with the spring.
8. Now continue to compress the spring.
9. Remove the spring and compressor assembly from the vehicle as soon as
you have attained sufficient compression.
10. With the spring supported turn the hexagonal drive nut in the opposite
direction and remove the compressor and yokes from the spring.
11. To re-mount the spring, reverse the procedure.
WARNING: AIR TOOLS MUST NOT BE USED TO ADJUST THE SPRING
COMPRESSOR. USE OF AIR TOOLS WILL INVALIDATE THE WARRANTY.
WARNING: DO NOT ALLOW THE SPRING WINDINGS TO TOUCH. DO NOT
ALLOW THE COMPRESSOR TO REACH THE LIMIT OF ITS TRAVEL IN EITHER
DIRECTION.
6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
MAINTAINING THE SPRING COMPRESSOR
• Before each use check the compressor to ensure it is not damaged
or worn.
• If any damage is suspected, do not use the unit, but contact your
local Clarke Dealer who will be able to advise you regarding repair
and spare parts.
• Grease the compressor spindle as necessary to inhibit corrosion.
• Keep the compressor clean, and when not in use, store in a safe,
dry, location.
7
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ALSO AVAILABLE FROM YOUR CLARKE DEALER
CHT695 OIL FILTER CAP WRENCH SET CHT701 12 PIECE OIL DRAIN PLUG
KEY SET
• Can withstand up to 85lb ft torque
• Oxide finish for rust protection
• Can be used with 3/8” & 1/2”
square drive wrenches
• Kit includes 14 wrenches, adaptor
and tough carry case
• 3/8" square drive carbon steel
tommy bar
• 7 Hex key drives 3/8", 8, 9, 10, 12, 14
& 17mm
• 4 Square key drives 3/8", 8, 11 &
13mm
CHT698 46 PIECE HARMONIC
BALANCE PULLER
CHT658 BRAKE CALIPER WIND BACK
TOOL SET
• Removes flywheels and
pulleys 36 to 95mm diameter
• Solid yoke designed for 2 or 3
point fixing
• 5" pressure screw
• Left & right hand
threaded bolt
assemblies
•Rewindtoolsand
reaction plate
• 15 adaptor plates to
suit a range of
vehicles
QR CODE
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Clarke Compresseur d'air
Clarke
Clarke 2241000 Mode d’emploi
Clarke
Clarke BOXER II 14/50P Mode d’emploi
Clarke
Clarke ZX 500 Guide de dépannage
Clarke
Clarke BOXER 14/50P Mode d’emploi
Clarke
Clarke PIONEER 210 OF Mode d’emploi
Clarke
Clarke RACER 9/50P Mode d’emploi
Clarke
Clarke CHAMP 262 Manuel d'installation et d'exploitation
Clarke
Clarke RANGER 6/500 Mode d’emploi
Clarke
Clarke RANGER 24 Mode d’emploi
Clarke
Clarke SHHH 2 Manuel d'installation et d'exploitation
Clarke
Clarke PP10ND Manuel d'installation et d'exploitation
Clarke
Clarke PP10ND Manuel d'installation et d'exploitation
Clarke
Clarke Raider 15/500 Mode d’emploi
Clarke
Clarke XE10/100 Mode d’emploi
Clarke
Clarke CFP9HND Manuel d'installation et d'exploitation
Clarke
Clarke BOXER 100 Mode d’emploi
Clarke
Clarke SHHHAIR 100/50 Mode d’emploi
Clarke
Clarke HUNTER 30 Mode d’emploi
Clarke
Clarke air Ranger 25 Manuel
Clarke
Clarke RACER 55 Mode d’emploi
Manuels Compresseur d'air populaires d'autres marques
Campbell Hausfeld
Campbell Hausfeld RP3300 Guide de démarrage rapide
Ingersoll-Rand
Ingersoll-Rand UP6 20 HP Manuel utilisateur
Hitachi
Hitachi EC99S Manuel de l'opérateur
Parkside
Parkside PKO 270 A1 Manuel utilisateur
Sullair
Sullair 185 Manuel utilisateur
Clas Ohlson
Clas Ohlson QIE-ZTH-15 Manuel utilisateur
