Clare ClareOne 16 Zone Hardwired Input Module Manuel utilisateur

ClareOne 16 Zone

Hardwired Input Module

Manual

Model CLR-C1-WD16

Last modified: 12/15/20

DOC ID - 1992 • Rev 02.01

This document may not be copied in whole or in part or otherwise

reproduced without prior written consent from Clare Controls, LLC.,

except where specifically permitted under US and international

Trademarks and

patents

The ClareOne name and logo are trademarks of Clare Controls,

LLC.

Other trade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the

respective products.

Manufacturer

Clare Controls, LLC.

7519 Pennsylvania Ave., Suite 104, Sarasota, FL 34243, USA

FCC compliance

FCC ID: 2ABBZ-RF-CHW16-433

IC ID: 11817A-CHW16433

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation. Changes or modifications not expressly

approved by the party responsible for compliance could void the

user's authority to operate the equipment. This Class B digital

apparatus complies with Canadian ICES-3B. Cet appareil numérique

de la classe B est conforme à la norme NMB-003 du Canada.

Note: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Warning: changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to

operate the equipment.

•This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance 20cm between the

radiator and your body.

EU compliance

Complete additional sections according to the governing laws and

standards for the intended marketplace.

EU directives

1999/5/EC (R&TTE directive): Hereby, Clare Controls, Llc. declares

that this device is in compliance with the essential requirements and

other relevant provisions of Directive 1999/5/EC.

2002/96/EC (WEEE directive): Products marked with this symbol

cannot be disposed of as unsorted municipal waste in the European

Union. For proper recycling, return this product to your local supplier

upon the purchase of equivalent new equipment, or dispose of it at

designated collection points. For more information see:

www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that

cannot be disposed of as unsorted municipal waste in the European

Union. See the product documentation for specific battery

information. The battery is marked with this symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb), or mercury

(Hg). For proper recycling, return the battery to your supplier or to a

designated collection point. For more information see:

www.recyclethis.info.

Contact information

For contact information, see www.clarecontrols.com.

16 Zone Hardwired Input Module i

Content

Introduction...1

Package contents...1

Specifications...1

Installation...3

Programming...6

Testing...7

Wiring...8

Reference information...10

Status definitions...10

EOL resistance...10

Multiple sensors on a zone...11

Troubleshooting...13

ii 16 Zone Hardwired Input Module

Important information

Limitation of liability

To the maximum extent permitted by applicable law, in no event will Clare

Controls, LLC. be liable for any lost profits or business opportunities, loss of use,

business interruption, loss of data, or any other indirect, special, incidental, or

consequential damages under any theory of liability, whether based in contract,

tort, negligence, product liability, or otherwise. Because some jurisdictions do not

allow the exclusion or limitation of liability for consequential or incidental

damages the preceding limitation may not apply to you. In any event the total

liability of Clare Controls, LLC. shall not exceed the purchase price of the

product. The foregoing limitation will apply to the maximum extent permitted by

applicable law, regardless of whether Clare Controls, LLC. has been advised of

the possibility of such damages and regardless of whether any remedy fails of its

essential purpose.

Installation in accordance with this manual, applicable codes, and the instructions

of the authority having jurisdiction is mandatory.

While every precaution has been taken during the preparation of this manual to

ensure the accuracy of its contents, Clare Controls, LLC. assumes no

responsibility for errors or omissions.

16 Zone Hardwired Input Module 1

Introduction

The ClareOne 16 Zone Hardwired Input Module (HWIM), model number

CLR-C1-WD16, allows the takeover of hardwired security zones making them

compatible with the ClareOne panel. The HWIM has 16 hardwired zone inputs

each with LED status, a tamper switch input, a back-up battery charging terminal,

and 2 auxiliary power outputs for powered sensors, capable of outputting 500mA

@ 12VDC. The HWIM supports powered and unpowered sensors, including

contact zones (open/close), motion sensors, and glass break detectors.

Package contents

Note: Ensure all accessories are included. If not, contact your dealer.

•1 × ClareOne 16 Zone Hardwired Input Module

•1 × Power supply

•2 × Battery cables (one red and one black)

•2 × Antennas

•16 × Resistors (each one is 4.7 k)

•1 × Installation sheet (DOC ID 1987)

•Mounting hardware (screws and wall anchors)

Specifications

Compatible panel

ClareOne (CLR-C1-PNL1)

Input voltage

16 VDC Plug-in transformer

Auxiliary voltage output

12 VDC @ 500 mA

EOL supervision

4.7 k(resistors included)

Battery backup

12 VDC 5Ah (optional, not included)

Input zones

Tamper zone

Use external switch or wire to short

Dimensions

5.5 x 3.5 in. (139.7 x 88.9 mm)

Operating environment

Temperature

Relative humidity

32 to 122°F (0 to 50°C)

95%

2 16 Zone Hardwired Input Module

Figure 1: ClareOne 16 Zone Hardwired Input Module and main LEDs

Processor LED (red color): The Processor LED flashes to indicate processor

operation.

RF XMIT LED (green color): The RF XMIT LED illuminates when RF

transmission is sent.

Pairing LED (red color): The Pairing LED illuminates when the HWIM is in

“Pairing” mode and is extinguished when the HWIM is in “Normal” mode. If there

are no zones paired the Pairing LED flashes.

Note: The Pairing LED must be extinguished (not in “Pairing” mode) when testing

sensors.

Figure 2: Zone LEDs

16 Zone Hardwired Input Module 3

Zone LEDs (red color): During "Normal Operation Mode" each LED remains off

until its corresponding zone is opened, then the LED illuminates. When entering

"Pairing Mode" each zone LED flashes briefly, after which each zone LED

remains off until the zone is learned in. Once learned in, it illuminates until

"Pairing Mode" is complete.

DLY LEDs (yellow color): Zones 1 and 2 each have a DLY LED. When a zone’s

DLY LED is illuminated yellow, that zone has the 2-minute communication timer

delay enabled. When the DLY LED is off, that zone’s communication timer delay

is disabled. When the DLY LED flashes, the associated zone has been tripped,

and the 2-minute communication timer delay is in effect. All additional triggers

from that sensor are ignored for 2 minutes. We recommend using zones 1 and 2

for motion sensors. For more information, see Programming on page 6.

Figure 3: Buttons

Memory Reset Button: The Memory Reset button clears the HWIM’s memory

and returns it to the factory default settings. The Memory Reset button is also

used to enable/disable the communication timer delay for Zones 1 and 2.

Pair Button: The Pair button puts the HWIM in/out of “Pairing” mode.

Installation

Only qualified installation technicians should install the HWIM. Clare Controls

does not assume responsibility for damages caused by improper installation or

use of the device. The HWIM is intended to be mounted to a wall using the

included screws and anchors. The HWIM should be oriented with its antennas

facing upward. The included antennas should be used regardless of location, for

optimal RF communication. Once all sensors are wired to the HWIM, the HWIM

and each zone can be paired to the ClareOne panel.

Note: If the HWIM is being installed in a metal container or equipment rack, the

antennas must extend outside the container to ensure that the RF

communication is not interrupted. Do not bend or alter the antennas.

4 16 Zone Hardwired Input Module

To install the HWIM:

1. Carefully select the mounting location, verifying that the HWIM’s antennas are

pointing up, and then secure it in position using the provided screws and wall

anchors.

Note: The HWIM should be within 1000 ft (304.8 m) of the panel. Walls,

construction materials, and other objects may impede the signal and shorten

the distance.

2. Attach each antenna to the HWIM, placing one in each of the ANT terminals

on the top of the HWIM.

Note: The antennas should be clear of obstructions and if in a metal

enclosure, should extend outside of it.

3. Wire the sensors/leads to the desired terminals marked Zone 1 through 16.

Wiring Notes:

•The HWIM requires 4.7 kΩ of end of line (EOL) resistance on each zone.

Existing installations may already have EOL resistors installed. Determine

the current EOL resistance value and adjust as needed to get total

resistance to 4.7 kΩ.

•EOL resistor installation depends on if the sensor is normally open (N/O)

or normally closed (N/C). Refer to Determining EOL resistance and sensor

type on page 5, for details on determining EOL resistance and if a sensor

is N/O or N/C.

•Install one of the included 4.7 kΩ resistors to each zone with an attached

sensor. Install the resistor in parallel for N/O and in series with N/C

sensors.

•To provide power to powered sensors, such as motion and glass break

sensors, wire the Positive and Negative leads from the sensor to the

“AUX” (+) and “GND” (-) terminals. See Figure 4 and 5, on page 8.

4. Wire the tamper switch input.

Note: This is required for proper device operation.

Option 1: If using a tamper switch, wire the tamper switch directly to the

tamper terminals without the need for an EOL resistor.

Option 2: If not using a tamper switch, connect a jumper wire across the

tamper input terminals.

5. (Recommended) For any security system that is supervised, a battery should

be connected to the HWIM. To provide an independent battery back up to the

HWIM, connect the included battery leads to a 12VDC, 5Ah lead acid

rechargeable battery (battery not included). This battery type is common with

traditional hardwired security panels, otherwise it is recommended that you

connect the HWIM to an auxiliary 16VDC power supply (1 amp or greater)

with its own battery backup.

Ce manuel convient aux modèles suivants

Table des matières

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur

clare ClareOne 16 Zone Hardwired Input Module Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques