CLA-VAL X144D e-FlowMeter Manuel utilisateur

From Flow Rate or Sensor Frequency screen, select to access menu.

Settings

X144D e-FlowMeter

Quick Start Programming

SETTINGS – VALVE (Adjust meter size and valve size parameters)

Note: Stylus Pen Recommended for Touch Screen Programming

6” 100-01 v1.0

VALVE

YES

Select then to configure meter size

VALVE YES

Size 1

Size 2

Size 3

Size 4

Select correct METER size from chart below

X144D Sizes 1 2 3 4

Full Port alve Sizes 2 2-1/2 3 4 6 8 10 12 14 16 18 20 24 30

Reduced Port alve Sizes 4 4 4 6 8 10 12 14 16 18 20 24 CF CF

YES Save configuration

SETTINGS – OUTPUT (Adjust Gain, mA Scaling, mA Filtering, Pulse Weight, and 4-20mA Output Test)

OUTPUT

YES

Select then to configure output.

OUTPUT YES

Set the Gain?

1.00

Default Gain is 1.00. Use arrow keys to adjust gain to desired value. Increasing or decreasing

value offsets factory calibration. Select to continue.

Set the 20mA Value?

002250.00

Use arrow keys to set 20mA Full Scale Output. Match 20mA value to customer display and/or

SCADA. Select to continue.

Set Filter Strength

4.0 width

Default Filter is 4.00. Use arrow keys to increase or decrease filtering of 4-20mA signal. The

higher the average filter strength, the longer the averaging time. Select to continue.

X144D e-FlowMeter

Quick Start Programming

SETTINGS – OUTPUT (Continued)

Set Pulse Weight?

01.000

Default Pulse Weight is 1.00. Use arrow keys to increase or decrease Pulse Weight.

Flow Rate = Number of Pulses x Pulse Weight / Time. Select to continue.

Set Flow Cutoff

030.00

This setting is used to set a minimum flow reading that is displayed on screen before displaying

zero flow. This is used when noise or vibration is causing erratic low flow readings when there is

no flow. Select to continue.

Are you sure you

want to save

changes?

YES

To save changes select .

To discard changes and advance to next menu select .

YES

Do you want to test

the 4-20mA Loop?

YES

To test 4 and 20mA outputs select . To return to settings menu select .

YES NO

0655

In this menu, a 4mA output signal is generated. To calibrate 4mA output to external device, use

arrow keys to increase or decrease 4mA output. A Digital Multimeter to measure 4mA output.

Select to continue to 20mA test.

EXIT

3273

In this menu, a 20mA output signal is generated. To calibrate 20mA output to external device,

use arrow keys to increase or decrease 20mA output. A Digital Multimeter to measure 20mA out-

put Select to return to Settings Menu.

EXIT

SETTINGS – DISPLA – UNITS

X144D e-FlowMeter

Quick Start Programming

DISPLAY

YES

Select to configure display settings.

DISPLAY

UNITS

YES

Select then to configure units settings.

UNITS YES

gpm

mgd

cfm

cfs

Select desired flow units for flow rate display. Select to save changes or

to discard changes and return to menu.

YES

NO DISPLAY

DISPLA – DECIMAL

DECIMAL

YES

Select then to configure decimal settings.

DECIMAL YES

0000.0

Use arrow key to select decimal point for flow rate home screen. Select to save

changes or to discard changes and return to menu.

YES

NO DISPLAY

DISPLA – OTHER – BRIGHTNESS

OTHER

BRIGHTNESS

Select then to configure screen brightness.

OTHER

BRIGHTNESS

Set Brightness?

SAVE

Use arrow keys to select desired brightness. Select to save changes and return to

menu.

SAVE

OTHER

X144D e-FlowMeter

Quick Start Programming

OTHER – TIMEOUT

TIMEOUT Select to configure screen sleep.

TIMEOUT

Set screen timeout?

SAVE

Use arrow keys to select desired duration before screen goes into sleep mode.

Select to save changes and return to menu. Use Timeout if powering

from battery source to save power consumption. If screen Timeout is set to 00 minutes, display

will not go into sleep mode.

SAVE OTHER

OTHER – RESET

OTHER

RESET

YES

Select to initiate Touch Screen Calibration.

Select to return to menu.

RESET YES

NO OTHER

LCD Cal

Touch Dots

Touch RED dots as they appear on touch screen.

Calib ation Done

Calib ation Failed!

Successful Touch Screen Calibration will result in message .

Touch to reboot and return to home screen. If message is

displayed, touch and repeat Touch Screen Calibration until successful calibration.

Calib ation Done

Calib ation Failed!

N-X144D QS-Programming

(R-03/2018)

CLA-VAL EUROPE

Chemin des Mésanges 1

CH-1032 Romanel/

Lausanne, Switzerland

Phone: 41-21-643-15-55

Fax: 41-21-643-15-50

E-mail: [email protected]

CLA-VAL FRANCE

Porte du Grand Lyon 1

ZAC du Champ du Périer

France - 01700 Neyron

Phone: 33-4-72-25-92-93

Fax: 33-4-72-25-04-17

E-mail: [email protected]

1701 Placentia Avenue •Costa Mesa, CA 92627

800-942-6326 Fax: 949-548-5441 Web Site: cla-val.com E-mail: [email protected]

©COPYRIGHT CLA-VAL 2018 Printed in USA Specifications subject to change without notice. visit www.cla-val-latinamerica.com for Spanish literature

CLA-VAL CANADA

4687 Christie Drive

Beamsville, Ontario

Canada L0R 1B4

Phone: 905-563-4963

Fax: 905-563-4040

E-mail [email protected]

CLA-VAL UK

Dainton House, Goods Station Road

Tunbridge Wells

Kent TN1 2 DH England

Phone: 44-1892-514-400

Fax: 44-1892-543-423

E-mail: [email protected]

CLA-VAL PACIFIC

45 Kennaway Road

Woolston, Christchurch, 8023

New Zealand

Phone: 64-39644860

www.cla-valpacific.com

E-mail: [email protected]

Autres manuels pour X144D e-FlowMeter

Table des matières

Autres manuels CLA-VAL Instrument de mesure

CLA-VAL

CLA-VAL e-Lift-34 Manuel utilisateur

CLA-VAL

CLA-VAL XP2F Manuel d'instructions

CLA-VAL

CLA-VAL X144D e-FlowMeter Manuel du propriétaire

CLA-VAL

CLA-VAL XP2F Manuel du propriétaire

CLA-VAL

CLA-VAL X144D e-FlowMeter Manuel utilisateur

CLA-VAL

CLA-VAL e-FlowMeter Manuel utilisateur

CLA-VAL

CLA-VAL VC12 Manuel de programmation

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur