Cisco WAP125 Manuel utilisateur

Autres manuels pour WAP125

3

Ce manuel convient aux modèles suivants

1

Autres manuels Cisco Point d'accès sans fil

Cisco

Cisco AIR-AP1251AG-A-k9 Manuel

Cisco

Cisco IW3702 Manuel utilisateur

Cisco

Cisco AT&T U-VERSE VEN401 Manuel utilisateur

Cisco

Cisco Aironet 1800i Manuel utilisateur

Cisco

Cisco WAP371 Manuel utilisateur

Cisco

Cisco WAP200 - Small Business Wireless-G Access... Manuel utilisateur

Cisco

Cisco WAP571 Manuel utilisateur

Cisco

Cisco Meraki GR10 Manuel utilisateur

Cisco

Cisco Aironet 1250 Series Manuel utilisateur

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manuel

Cisco

Cisco AIR-LMC352 Manuel utilisateur

Cisco

Cisco AIR-LAP1242AG-A-K9 Manuel utilisateur

Cisco

Cisco Catalyst 9164 Series Manuel utilisateur

Cisco

Cisco Catalyst 9130AX Series Manuel utilisateur

Cisco

Cisco AIR-LAP1252AG-A-K9 - Aironet 1252AG - Wireless Access... Manuel utilisateur

Cisco

Cisco FM1000 Gateway Manuel

Cisco

Cisco Aironet 1400 Series Manuel

Cisco

Cisco Aironet 1600 Series Manuel utilisateur

Cisco

Cisco Aironet 521 Manuel utilisateur

Cisco

Cisco Aironet 1600 Series Guide de référence rapide

Cisco

Cisco 1232AG - Aironet - Wireless Access Point Manuel

Cisco

Cisco MERAKI MR34 Manuel utilisateur

Cisco

Cisco WAP371 Manuel utilisateur

Cisco

Cisco AIR-AP1131G-A-K9 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur

●

●

●

●

●

●

●

Reboot and Reset the WAP125 and WAP581

to Factory Default Settings

Objective

Rebooting or restarting the Wireless Access Point (WAP) deletes the logs stored in the

volatile memory. This process is performed when certain changes in the settings need a

reboot or if the WAP is not responding or booting up properly. Resetting the WAP to factory

default settings, on the other hand, erases all configurations that have been set by the user,

and restores the device to its original settings. A reset is recommended if most of the WAP

settings need to be reconfigured.

This article aims to show you how to reboot and reset your WAP125 or WAP581 to factory

default settings.

Applicable Devices

WAP125

WAP581

Software Version

WAP125 - 1.0.0.3

WAP581 - 1.0.0.4

Reboot the Wireless Access Point

There are two ways to reboot the WAP:

Hardware reboot

Reboot through the web-based utility

Hardware Reboot

You have two ways to reboot the device hardware:

Turn the device off by pressing the POWER button while the device is connected to the power

outlet.

●

Note: The POWER button only works if the device is using a power adapter. If power is

supplied through Power over Ethernet (PoE), unplug your Ethernet connection for three

seconds then plug it back.

Press the Reset button for about three seconds only, or until the lights go off.

Note: In both above images, the WAP125 is pictured.

Reboot through the Web-based Utility

Step 1. Log in to the web-based utility of your WAP and choose Administration > Reboot.

Step 2. Click the Reboot button.

Step 3. Click OK in the confirmation window.

You should now have rebooted your device.

Schedule a Reboot

Step 1. Log in to the web-based utility of your WAP and choose Administration > Reboot.

Step 2. Check the Enable Schedule Reboot check box to configure the schedule settings.

Step 3. Choose a radio button under Schedule Reboot to determine the date and time the

●

●

WAP should reboot. The options are:

Date — Set the specific date and time a reboot should occur.

In — Set the reboot to occur from the time the function was configured. If this is chosen, skip

to Step 6.

Note: In this example, Date is chosen.

Step 4. (Optional) If Date was chosen in Step 3, click the Date field and choose the date you

want to set the WAP to reboot.

Note: In this example, 2017-06-07 is chosen.

Step 5. In the Time area, choose the hour and minute from the respective drop-down list.

The time format is in Military format.

Note: In this example, the WAP is scheduled to reboot at 3:21am on June 7, 2017.

Step 6. (Optional) If In was chosen in Step 3, from the Days drop-down list, choose the

number of days from today that the WAP should reboot.

Note: In this example, 7 is chosen.

Step 7. (Optional) From the Hours drop-down list, choose the hour of the day for the WAP to

reboot. This option is useful if you want to set a specific hour of the day for this to occur.

Note: In this example, the WAP is scheduled to reboot 7 days from now at 3 AM.

●

●

Step 8. (Optional) From the Minutes drop-down list, choose the minute in the hour for the

WAP to reboot.

Note: In this example, 0 is chosen.

Step 9. Click Save.

You should now have successfully configured a schedule for the WAP to reboot.

Reset the Wireless Access Point

There are two ways to reset the WAP to factory default settings:

Hardware reset

Reset through the web-based utility

Hardware Reset

Step 1. Press the Reset button for more than 10 seconds until the lights go off.

Step 2. Release the Reset button when the lights turn back on.

Note: In both above images, the WAP125 is pictured.

Reset through the Web-based Utility

Step 1. Log in to the web-based utility of your WAP and choose Administration > Reboot.

Step 2. Check the Restore to Factory Default Settings check box.

Step 3. Click the Reboot button.

Step 4. Click OK in the confirmation window.

You should now have reset your device to factory default settings.