Cisco ASA 5506W-X Manuel utilisateur

Contents

Introduction

Prerequisites

Requirements

Components Used

Network Diagrams

Configure

Step 1. Modify Interface IP configuration on ASA

Step 2. Modify DHCP pool settings on both inside and wifi interfaces

Step 3. Specify DNS server to pass to inside and WiFI DHCP clients

Step 4. Modify HTTP access configuration on the ASA for Adaptive Security Device Manager

(ASDM) access:

Step 5. Modify Interface IP for Access Point Management in WLAN console (interface BVI1):

Step 6. Modify default-gateway on WAP

Step 7. Modify the FirePOWER Module Management IP Address (Optional)

If the ASA Management1/1 interface is connected to an inside switch:

If the ASA is NOT connected to an inside switch:

Step 8. Connect to AP GUI to enable radios and set other WAP configuration

WAP CLI Configuration for a single wireless VLAN using modified IP ranges

Configurations

ASA Configuration

Aironet WAP Configuration (without the example SSID config)

FirePOWER Module Configuration (with inside switch)

FirePOWER Module Configuration (without inside switch)

Verify

Configure DHCP with Multiple Wireless VLANs

Step 1. Remove Existing DHCP configuration on Gig1/9

Step 2. Create Subinterfaces for Each VLAN on Gig1/9

Step 3. Designate a DHCP pool for each VLAN

Step 4. Configure the Access Point SSIDs, save the config, and reset the module

Troubleshoot

Introduction

This document describes how to perform initial installation and configuration of a Cisco Adaptive

Security Appliance (ASA) 5506W-X device when the default IP addressing scheme needs to be

modified to fit into an existing network or if multiple wireless VLANs are required. There are

several configuration changes that are required when modifying the default IP addresses in order

to access the wireless access point (WAP) as well as ensure that other services (such as DHCP)

continue to function as expected. In addition, this document provides some CLI configuration

examples for the integrated Wireless Access Point (WAP) to make it easier to complete initial

configuration of the WAP. This document is intended to supplement the existing Cisco ASA 5506-

X Quick Start guide available on the Cisco website.

Prerequisites

This document only applies to the initial configuration of a Cisco ASA5506W-X device that

contains a wireless access point and is only intended to address the various changes needed

when you modify the existing IP addressing scheme or add additional wireless VLANs. For default

configuration installations, the existing ASA 5506-X Quick Start Guide must be referenced.

Requirements

Cisco recommends that you have knowledge of these topics:

Cisco ASA 5506W-X device

●

Client machine with a terminal emulation program such as Putty, SecureCRT, etc.

●

Console Cable and Serial PC Terminal Adapter (DB-9 to RJ-45)

●

Components Used

The information in this document is based on these software and hardware versions:

Cisco ASA 5506W-X device

●

Client machine with a terminal emulation program such as Putty, SecureCRT, etc.

●

Console Cable and Serial PC Terminal Adapter (DB-9 to RJ-45)

●

ASA FirePOWER Module

●

Integrated Cisco Aironet 702i wireless access point (Built-in WAP)

●

The information in this document was created from the devices in a specific lab environment. All of

the devices used in this document started with a cleared (default) configuration. If your network is

live, make sure that you understand the potential impact of any command.

Network Diagrams

As shown in this image, examples of the IP addressing that will be applied in two different

topologies:

ASA + FirePOWER with an inside switch:

ASA + FirePOWER without an inside switch:

Configure

These steps must be performed in order after you power on and boot the ASA with the console

cable connected to the client.

Step 1. Modify Interface IP configuration on ASA

Configure the inside (GigabitEthernet 1/2) and wifi (GigabitEthernet 1/9) interfaces to have IP

addresses as needed within the existing environment. In this example, inside clients are on the

10.0.0.1/24 network and WIFI clients are on the 10.1.0.1/24 network.

asa(config)# interface gigabitEthernet 1/2

asa(config-if)# ip address 10.0.0.1 255.255.255.0

asa(config)# interface gigabitEthernet 1/9

asa(config-if)# ip address 10.1.0.1 255.255.255.0

Note: You will get this warning when you change the above interface IP addresses. This is

expected.

Interface address is not on same subnet as DHCP pool

WARNING: DHCPD bindings cleared on interface 'inside', address pool removed

Step 2. Modify DHCP pool settings on both inside and wifi interfaces

This step is required if the ASA is to be used as the DHCP server in the environment. If another

DHCP server is used to assign IP addresses to clients then DHCP should be disabled on the ASA

altogether. Since you have now changed our IP addressing scheme, you need to alter the existing

IP address ranges that the ASA is providing to clients. These commands will create new pools to

match the new IP address range:

asa(config)# dhcpd address 10.0.0.2-10.0.0.100 inside

asa(config)# dhcpd address 10.1.0.2-10.1.0.100 wifi

Also the modification of the DHCP pools will disable the previous DHCP server on the ASA, and

you will need to re-enable it.

asa(config)# dhcpd enable inside

asa(config)# dhcpd enable wifi

If you do not change the interface IP addresses before making the DHCP changes then you will

receive this error:

asa(config)# dhcpd address 10.0.0.2-10.0.0.100 inside

Address range subnet 10.0.0.2 or 10.0.0.100 is not the same as inside interface subnet

192.168.1.1

Step 3. Specify DNS server to pass to inside and WiFI DHCP clients

When they assign IP addresses via DHCP, most clients also need to be assigned a DNS server by

the DHCP server. These commands will configure the ASA to include the DNS server located at

10.0.0.250 to all clients. You need to substitute the 10.0.0.250 for either an internal DNS server or

a DNS server provided by your ISP.

asa(config)# dhcpd dns 10.0.0.250 interface inside

asa(config)# dhcpd dns 10.0.0.250 interface wifi

Step 4. Modify HTTP access configuration on the ASA for Adaptive Security

Device Manager (ASDM) access:

Since the IP addressing has been changed, HTTP access to the ASA also needs to be modified

so that clients on the inside and WiFI networks can access ASDM to manage the ASA.

asa(config)# no http 192.168.1.0 255.255.255.0 inside

asa(config)# no http 192.168.10.0 255.255.255.0 wifi

asa(config)# http 0.0.0.0 0.0.0.0 inside asa(config)# http 0.0.0.0 0.0.0.0 wifi

Note: This configuration allows any client on the inside or wifi interfaces to access the ASA

via ASDM. As a security best practice, you must limit the scope of addresses to trusted

clients only.

Step 5. Modify Interface IP for Access Point Management in WLAN console

(interface BVI1):

asa# session wlan console

ap>enable

Password: Cisco

ap#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

ap(config)#interface BVI1

ap(config-if)#ip address 10.1.0.254 255.255.255.0

Step 6. Modify default-gateway on WAP

This step is required so that the WAP knows where to send all traffic that is not originated on the

local subnet. This is required to provide to access the WAP GUI via HTTP from a client on the

ASA inside interface.

ap(config)#ip default-gateway 10.1.0.1

Step 7. Modify the FirePOWER Module Management IP Address (Optional)

If you also plan to deploy the Cisco FirePOWER (also known as SFR) module then you also need

to change its IP address in order to access it from the physical Management1/1 interface on the

ASA. There are two basic deployment scenarios that determine how to configure the ASA and the

SFR module:

A topology in which the ASA Management1/1 interface is connected to an inside switch (as

per the normal quick start guide)

A topology where an inside switch is not present.2.

Depending on your scenario,these are the appropriate steps:

If the ASA Management1/1 interface is connected to an inside switch:

You can session into the module and change it from the ASA before connecting it to an inside

switch. This configuration allows you to access the SFR module via IP by placing it on the same

subnet as the ASA inside interface with an IP address of 10.0.0.254.

Lines in bold are specific to this example and are required for establishing IP connectivity.

Lines in italics will vary by environment.

asa# session sfr console

Opening console session with module sfr.

Connected to module sfr. Escape character sequence is 'CTRL-^X'.

Cisco ASA5506W v5.4.1 (build 211)

Sourcefire3D login: admin

Password: Sourcefire

<<Output Truncated - you will see a large EULA>>

Please enter 'YES' or press <ENTER> to AGREE to the EULA: YES

System initialization in progress. Please stand by.

You must change the password for 'admin' to continue.

Enter new password:

Confirm new password:

You must configure the network to continue.

You must configure at least one of IPv4 or IPv6.

Do you want to configure IPv4? (y/n) [y]: y

Do you want to configure IPv6? (y/n) [n]: n

Configure IPv4 via DHCP or manually? (dhcp/manual) [manual]:

Enter an IPv4 address for the management interface [192.168.45.45]: 10.0.0.254Enter an IPv4

netmask for the management interface [255.255.255.0]: 255.255.255.0

Enter the IPv4 default gateway for the management interface []: 10.0.0.1

Enter a fully qualified hostname for this system [Sourcefire3D]: Cisco_SFR

Enter a comma-separated list of DNS servers or 'none' []: 10.0.0.250

Enter a comma-separated list of search domains or 'none' [example.net]: example.net

If your networking information has changed, you will need to reconnect.

For HTTP Proxy configuration, run 'configure network http-proxy'

Applying 'Default Allow All Traffic' access control policy.

Note: It may take a couple minutes for the default access control policy to apply on the SFR

module. Once it is complete, you can escape out of the SFR module CLI and back into the

ASA by pressing CTRL + SHIFT + 6 +X (CTRL ^ X)

If the ASA is NOT connected to an inside switch:

An inside switch may not exist in some small deployments. In this type of topology, clients would

generally connect to the ASA via the WiFi interface. In this scenario, it is possible eliminate the

need for an external switch and access the SFR module via a separate ASA interface by cross-

connecting the Management1/1 interface to another physical ASA interface.

In this example, a physical ethernet connection must exist between the ASA GigabitEthernet1/3

interface and the Management1/1 interface. Next, you configure the ASA and SFR module to be

on a separate subnet and then you are able to access the SFR from both the ASA as well as

clients located on the inside or wifi interfaces.

ASA Interface Configuration:

asa(config)# interface gigabitEthernet 1/3

asa(config-if)# ip address 10.2.0.1 255.255.255.0

asa(config-if)# nameif sfr

INFO: Security level for "sfr" set to 0 by default.

asa(config-if)# security-level 100

asa(config-if)# no shut

SFR Module Configuration:

asa# session sfr console

Opening console session with module sfr.

Connected to module sfr. Escape character sequence is 'CTRL-^X'.

Cisco ASA5506W v5.4.1 (build 211)

Sourcefire3D login: admin

Password: Sourcefire

<<Output Truncated - you will see a large EULA>>

Please enter 'YES' or press <ENTER> to AGREE to the EULA: YES

System initialization in progress. Please stand by.

You must change the password for 'admin' to continue.

Enter new password:

Confirm new password:

You must configure the network to continue.

You must configure at least one of IPv4 or IPv6.

Do you want to configure IPv4? (y/n) [y]: y

Do you want to configure IPv6? (y/n) [n]: n

Configure IPv4 via DHCP or manually? (dhcp/manual) [manual]:

Enter an IPv4 address for the management interface [192.168.45.45]: 10.2.0.254

Enter an IPv4 netmask for the management interface [255.255.255.0]: 255.255.255.0

Enter the IPv4 default gateway for the management interface []: 10.2.0.1

Enter a fully qualified hostname for this system [Sourcefire3D]: Cisco_SFR Enter a comma-

separated list of DNS servers or 'none' []: 10.0.0.250 Enter a comma-separated list of search

domains or 'none' [example.net]: example.net If your networking information has changed, you

will need to reconnect. For HTTP Proxy configuration, run 'configure network http-proxy'

Applying 'Default Allow All Traffic' access control policy.

Note: It may take a couple minutes for the default access control policy to apply on the SFR

module. Once it is complete, you can escape out of the SFR module CLI and back into the

ASA by pressing CTRL + SHIFT + 6 +X (CTRL ^ X).

Once the SFR configuration applies, you must be able to ping the SFR management IP address

from the ASA:

asa# ping 10.2.0.254

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.2.0.254, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms

asa#

If you cannot ping the interface successfully, verify the configuration and state of physical ethernet

connections.

Step 8. Connect to AP GUI to enable radios and set other WAP configuration

At this point you should have connectivity to manage the WAP via the HTTP GUI as discussed in

the quick start guide. You will either need to browse to the IP address of the WAP's BVI interface

from a web browser of a client that is connected to the inside network on the 5506W or you can

apply the example configuration and connect to the SSID of the WAP. If you do not use the CLI

below, you need to plug in the ethernet cable from your client to the Gigabit1/2 interface on the

ASA.

If you prefer to use the CLI to configure the WAP, you can session into it from the ASA and use

this example configuration. This creates an open SSID with the name of 5506W and 5506W_5Ghz

so that you can use a wireless client to connect to and further manage the WAP.

Note: After applying this configuration you will want to access the GUI and apply security to

the SSIDs so that the wireless traffic is encrypted.

WAP CLI Configuration for a single wireless VLAN using modified IP ranges

dot11 ssid 5506W

authentication open

guest-mode

dot11 ssid 5506W_5Ghz

authentication open

guest-mode

interface Dot11Radio0

ssid 5506W

interface Dot11Radio1

ssid 5506W_5Ghz

interface BVI1

ip address 10.1.0.254 255.255.255.0

ip default-gateway 10.1.0.1

interface Dot11Radio0

no shut

interface Dot11Radio1

no shut

From this point on, you can perform the normal steps to complete the configuration of the WAP

and you must be able to access it from the web browser of a client connected to the above created

SSID. The default username of the access point is Cisco with a password of Cisco with a capital

Cisco ASA 5506-X Series Quick Start Guide

http://www.cisco.com/c/en/us/td/docs/security/asa/quick_start/5506X/5506x-quick-start.html#pgfId-

138410

You need to use the IP address of 10.1.0.254 instead of the 192.168.10.2 as stated in the Quick

Start Guide.

Configurations

The resulting configuration must match the output (assuming you used the example IP ranges,

otherwise substitute accordingly:

ASA Configuration

Interfaces:

Note: The lines in italics only apply if you do NOT have an inside switch:

asa# sh run interface gigabitEthernet 1/2

interface GigabitEthernet1/2

nameif inside

security-level 100

ip address 10.0.0.1 255.255.255.0

asa# sh run interface gigabitEthernet 1/3

interface GigabitEthernet1/3

nameif sfr

security-level 100

ip address 10.2.0.1 255.255.255.0 asa# sh run interface gigabitEthernet 1/9

interface GigabitEthernet1/9

nameif wifi

security-level 100

ip address 10.1.0.1 255.255.255.0

asa#

DHCP:

asa# sh run dhcpd

dhcpd auto_config outside **auto-config from interface 'outside' **auto_config dns x.x.x.x

x.x.x.x <-- these lines will depend on your ISP **auto_config domain isp.domain.com <-- these

lines will depend on your ISP ! dhcpd address 10.0.0.2-10.0.0.100 inside dhcpd dns 10.0.0.250

interface inside dhcpd enable inside ! dhcpd address 10.1.0.2-10.1.0.100 wifi dhcpd dns

10.0.0.250 interface wifi dhcpd enable wifi ! asa#

HTTP:

asa# show run http

http server enable

http 0.0.0.0 0.0.0.0 outside

http 0.0.0.0 0.0.0.0 inside

asa#

Aironet WAP Configuration (without the example SSID config)

asa# session wlan console

ap>enable

Password: Cisco

ap#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

ap#show configuration | include default-gateway

ip default-gateway 10.1.0.1

ap#show configuration | include ip route

ip route 0.0.0.0 0.0.0.0 10.1.0.1

ap#show configuration | i interface BVI|ip address 10

interface BVI1 ip address

10.1.0.254 255.255.255.0

FirePOWER Module Configuration (with inside switch)

asa# session sfr console

Opening console session with module sfr.

Connected to module sfr. Escape character sequence is 'CTRL-^X'.

> show network

===============[ System Information ]===============

Hostname : Cisco_SFR

Domains : example.net

DNS Servers : 10.0.0.250

Management port : 8305

IPv4 Default route

Gateway : 10.0.0.1

======================[ eth0 ]======================

State : Enabled

Channels : Management & Events

Mode :

MDI/MDIX : Auto/MDIX

MTU : 1500

MAC Address : B0:AA:77:7C:84:10

----------------------[ IPv4 ]---------------------Configuration : Manual

Address : 10.0.0.254

Netmask : 255.255.255.0

Broadcast : 10.0.0.255

----------------------[ IPv6 ]----------------------

Configuration : Disabled

===============[ Proxy Information ]================

State : Disabled

Authentication : Disabled

FirePOWER Module Configuration (without inside switch)

asa# session sfr console

Opening console session with module sfr.

Connected to module sfr. Escape character sequence is 'CTRL-^X'.

> show network

===============[ System Information ]===============

Hostname : Cisco_SFR

Domains : example.net

DNS Servers : 10.0.0.250

Management port : 8305

IPv4 Default route

Gateway : 10.2.0.1

======================[ eth0 ]======================

State : Enabled

Channels : Management & Events

Mode :

MDI/MDIX : Auto/MDIX

MTU : 1500

MAC Address : B0:AA:77:7C:84:10

----------------------[ IPv4 ]---------------------

Configuration : Manual

Address : 10.2.0.254

Netmask : 255.255.255.0

Broadcast : 10.2.0.255

----------------------[ IPv6 ]----------------------

Configuration : Disabled

===============[ Proxy Information ]================

State : Disabled

Authentication : Disabled

Verify

In order to verify that you have the proper connectivity to the WAP for completing the installation

process:

Connect your test client to the ASA inside interface and ensure that it receives an IP address

from the ASA via DHCP that is within the desired IP range.

Use a web browser on your client in order to navigate to https://10.1.0.254 and verify that the

AP GUI is now accessible.

Ping the SFR management interface from the inside client and the ASA to verify proper

connectivity.

Configure DHCP with Multiple Wireless VLANs

The configuration assumes that you use a single wireless VLAN. The Bridge Virtual Interface (BVI)

on the Wireless AP can provide a bridge for Multiple VLANs. Because of the syntax for DHCP on

the ASA, if you wish to configure the 5506W as a DHCP server for multiple VLANs, you need to

create subinterfaces on the Gigabit1/9 interface and give each a name. This section guides you

through the process of how to remove the default configuration and to apply the configuration

necessary to set the ASA up as a DHCP server for multiple VLANs.

Step 1. Remove Existing DHCP configuration on Gig1/9

First, remove the existing DHCP configuration on the Gig1/9 (wifi) interface:

ciscoasa# no dhcpd address 10.1.0.2-10.1.0.100 wifi

ciscoasa# no dhcpd enable wifi

Autres manuels pour ASA 5506W-X

Table des matières

Autres manuels Cisco Point d'accès sans fil

Cisco

Cisco Catalyst 9124AX Series Manuel

Cisco

Cisco FM1000 Gateway Manuel

Cisco

Cisco Catalyst 9117AX Series Manuel utilisateur

Cisco

Cisco aironet 2800 series Guide de référence rapide

Cisco

Cisco Catalyst 9166I Series Manuel utilisateur

Cisco

Cisco WAP131 Mode d’emploi

Cisco

Cisco AIR-AP1121G-E-K9 Manuel

Cisco

Cisco Aironet 1520 Series Manuel utilisateur

Cisco

Cisco Catalyst IW9167I Manuel

Cisco

Cisco Aironet 1250 Series Manuel utilisateur

Cisco

Cisco Meraki MR42 Manuel utilisateur

Cisco

Cisco Aironet 1850 Series Manuel utilisateur

Cisco

Cisco WAP121 Manuel utilisateur

Cisco

Cisco Aironet 1600 Series Manuel utilisateur

Cisco

Cisco 1004-CH - 1004 Enet/ISDN/Bri Rter Guide de référence rapide

Cisco

Cisco AT&T U-VERSE VEN401 Manuel utilisateur

Cisco

Cisco Aironet 1260 Series Manuel utilisateur

Cisco

Cisco ASA 5506-X Manuel utilisateur

Cisco

Cisco Catalyst 9120AX Series Manuel utilisateur

Cisco

Cisco AIR-LAP1310G Manuel utilisateur

Cisco

Cisco WAP2000 Mode d’emploi

Cisco

Cisco Aironet 1815T Manuel utilisateur

Cisco

Cisco Aironet 1815w Manuel utilisateur

Cisco

Cisco Aironet 1530 Series, 1532 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur