Cisco Meraki MS210-24 Manuel utilisateur

MS210 Series Installation Guide

Model number Description

MS210-24 Stackable Layer-2 24-port gigabit Ethernet switch with 4 SFP interfaces

MS21024P Stackable Layer-2 24-port gigabit Ethernet 370W PoE switch with 4 SFP interfaces

MS210-48 Stackable Layer-2 48-port gigabit Ethernet switch with 4 SFP interfaces

MS210-48LP Stackable Layer-2 48-port gigabit Ethernet 370W PoE switch with 4 SFP interfaces

MS210-48FP Stackable Layer-2 48-port gigabit Ethernet 740W PoE switch with 4 SFP interfaces

Package contents

In addition to the MS switch, the following are provided:

Rack Mount Kit includes:

• US 12-24 mounting screws and cage nuts, 5 of each

• INTL M5 mounting screws and cage nuts, 5 of each

• INTL M6 mounting screws and cage nuts, 5 of each

• Mounting washers

MS210-24 Series front panel

MS210-48 Series front panel

Ports and Status Indicators

The MS uses LEDs to inform the user of the device's status. When the device powers on, all the Internet LEDs flash

twice. Additional functions are described below, from left to right.

Item Function LED Status Meaning

1 Power Solid orange Switch is unable to connect to the Meraki cloud

Flashing white Firmware upgrade in process

Solid white Switch is fully operational and connected to the Meraki cloud

Off Switch does not have power

2 Restore N/A Restore button to clear switch IP and local configuration

settings

3 Switch Ports Off No link is detected on this port

Note: MS210 does not include stacking cables. Stacking cables sold separately.

Solid orange 10/100 Mbps

Solid green 1 Gbps

In addition, there is a RESTORE button available on the front panel.

Insert a paperclip if a restore is required.

• A brief, momentary press: To delete a downloaded configuration and reboot.

• Press and hold for more than 10 sec: To force the unit into a full factory restore.

MS210 Series back panel

Item Function LED Status Meaning

1 Management Interface Green

Connected, used for easy

access to the local status

page

2 Stack Ports Green QSFP stacking cable is

connected

Off No link is detected on this

port

322-Pin Redundant Power

Supply Connector N/A

RPS2300 can be

connected to provide

redundant power in case

of a failover

Power input Power cords may be ordered separately.

Equipment is to be used only in a restricted access location and installed/operated only by trained service personnel.

RPS2300 Redundant Power Supply (Optional)

The MS210 series supports connecting the Cisco RPS2300 for optional power redundancy. MS210 series models

support failover and reversion to main power once it has been restored. The following Cisco part numbers are

supported:

Part number Description

PWR-RPS2300 RPS Chassis

C3K-PWR-750WAC 750W RPS Power supply (see recommendations)

C3K-PWR-1150WAC 1150W RPS Power supply (see recommendations)

CAB-RPS2300-E= RPS 22-pin cable

Bringing your Stack Online

MS210 switches can be connected in a physical stack using dedicated stacking ports and cables. Configuration steps

and additional information about stacking can be found here.

Mounting hardware

The mounting hardware includes a rack mount kit for standard 1U racks. When installing the device, make sure that

there is sufficient space between the rear of the rack and other obstacles to ensure adequate airflow.

Optional Mid-Mount bracket

MS210 48 port models are designed for an optional MA-MNT-MID-1 mid-mount bracket when using 2-post racks.

The MS210 and MS225 series switches additionally support cross-model stacking, meaning an MS210 can be

stacked with an MS225 and vice-versa.

Ce manuel convient aux modèles suivants

Autres manuels Cisco Changer

Cisco

Cisco Nexus 1000V Manuel utilisateur

Cisco

Cisco Nexus 9336C-FX2-E Manuel

Cisco

Cisco Catalyst 2960 Series Manuel utilisateur

Cisco

Cisco SRW248G4P Manuel utilisateur

Cisco

Cisco 3020 - Cisco Catalyst Blade Switch Mode d’emploi

Cisco

Cisco 3560G-24PS - Catalyst Switch Dimensions

Cisco

Cisco NMH Series Manuel utilisateur

Cisco

Cisco Nexus 1000V Manuel utilisateur

Cisco

Cisco 2975 - Catalyst LAN Base Switch Manuel

Cisco

Cisco Catalyst WS-C3850-24T-L Instructions d'utilisation et de sécurité

Cisco

Cisco Nexus 3000 series Manuel utilisateur

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Manuel utilisateur

Cisco

Cisco Catalyst 3130 Manuel utilisateur

Cisco

Cisco MDS 9000 Series Manuel utilisateur

Cisco

Cisco 2900 - Catalyst Expansion Module Manuel utilisateur

Cisco

Cisco Nexus 7000 Series Manuel d'installation

Cisco

Cisco TOPSPIN SFS 3012 Manuel utilisateur

Cisco

Cisco AMP8050 Manuel

Cisco

Cisco 11154 - CSS - Switch Manuel utilisateur

Cisco

Cisco FAN-MOD-3 Manuel

Cisco

Cisco SLM248P Manuel utilisateur

Cisco

Cisco Catalyst 5000 Series Guide rapide

Cisco

Cisco PFC4 Manuel d'installation et d'exploitation

Cisco

Cisco Nexus 7000 Series Manuel d'installation et d'exploitation

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur