Cisco Catalyst 9500 Series Manuel

Switch Installation

For initial switch setup, assigning the switch IP address, and powering on information, see the switch getting

started guide on Cisco.com.

This chapter contains these topics:

•Installation Tasks, page 1

•Safety Warnings, page 2

•Unpacking the Switch, page 3

•Establishing the System Ground, page 3

•Installing the Switch, page 5

Installation Tasks

The process of installing the switch can be broken down into a series of tasks, which are described in the

following table.

DescriptionTask

Remove the switch from the packaging materials.

Save the packaging material for later use if

you need to move the chassis.

Note

Unpacking the switch

Install the switch.Installing the switch

Construct and attach a system ground wire from the

building (earth) ground to the system ground point

on the chassis.

Connecting the chassis to system ground

Power supplies that are ordered with the switch are

installed in the switch. If ordered separately, install

the power supplies. Connect the power supplies.

Installing and cabling the power supply or supplies

Install a network modules on the uplink ports.Installing a network module

Cisco Catalyst 9500 Series Switches Hardware Installation Guide

DescriptionTask

Install the fan modules in the fan slots.Installing the fan

The various ports on the chassis must be connected

to the network. This process can involve only

attaching a network interface cable to the port or it

can include the installation of a transceiver of some

type in port and then attaching the network interface

cable to the transceiver.

Cabling the chassis and modules to the network

After completing the network cabling and making

sure that system ground is connected, the power

supplies can be turned on. The system powers up and

runs through a set of built-in diagnostics.

Powering up the chassis

Safety Warnings

Class 1 laser product. Statement 1008Warning

This unit is intended for installation in restricted access areas. A restricted access area can be accessed

only through the use of a special tool, lock and key, or other means of security. Statement 1017

Warning

This unit might have more than one power supply connection. All connections must be removed to

de-energize the unit. Statement 1028

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning

To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the

handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to

support the weight of the unit. Statement 1032

Warning

Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when

servicing. Statement 1034

Warning

This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation.

Install only in accordance with national and local wiring regulations. Statement 1045

Warning

Cisco Catalyst 9500 Series Switches Hardware Installation Guide

Switch Installation

Safety Warnings

When installing or replacing the unit, the ground connection must always be made first and disconnected

last. Statement 1046

Warning

Installation of the equipment must comply with local and national electrical codes.. Statement 1074Warning

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams

or view directly with optical instruments. Statement 1051

Warning

Unpacking the Switch

Do not discard the shipping container when you unpack the switch. Flatten the shipping cartons and store

them with the pallet. You will need these containers if you need to move or ship the switch in the future.

Note

Check the contents of the accessory kit. Verify that you received all listed equipment, which should include

the following:

•Grounding lug and disposable ESD strap.

•Optional equipment that you ordered, such as console cables, transceivers, or special connectors.

•Blank covers are installed for the power supply slots on the chassis.

Establishing the System Ground

This section describes how to connect a system ground to the switch.

Installations that rely solely on system grounding using only an AC third-prong ground run a substantially

greater risk of equipment problems and data corruption than those installations that use both the AC

third-prong ground and a properly installed system ground.

Caution

The system ground provides additional grounding for EMI shielding requirements and grounding for the low

voltage supplies (DC-DC converters) on the modules. You must observe the following system grounding

guidelines for your chassis:

•You must install the system ground connection with any other rack or system power ground connections

that you make. The system ground connection is required if FXS modules are installed or if this equipment

is installed in a U.S. or European Central Office.

•You must connect both the system ground connection and the power supply ground connection to an

earth ground. The system ground connection is required if FXS modules are installed or if this equipment

is installed in a U.S. or European Central Office.

•When using DC-input power supplies, you must install the system (ground before you attach the source

DC power cables to the DC PEM. Power down the chassis before attaching the system ground.

Cisco Catalyst 9500 Series Switches Hardware Installation Guide

Switch Installation

Unpacking the Switch

In all situations, grounding practices must comply with Section 250 of the National Electric Code (NEC)

requirements or local laws and regulations. An 8-24 AWG grounding wire is preferred from the chassis

to the rack ground or directly to the common bonding network (CBN). The equipment rack should also

be connected to the CBN with 8-24 AWG grounding wire.

Note

The system ground serves as the primary safety ground for chassis that are equipped with DC-input power

supplies. The DC-input power supplies for these chassis do not have a separate ground.

Note

Required Tools and Equipment

To connect the system ground, you need the following tools and materials:

•Grounding lug—A two-hole standard barrel lug. Supports up to 8-24 AWG wire. Supplied as part of

accessory kit.

•Grounding screws—Two M4 x 8 mm (metric) pan-head screws. Supplied as part of the accessory kit.

•Grounding wire—Not supplied as part of accessory kit. The grounding wire should be sized according

to local and national installation requirements. Depending on the power supply and system, a 12 AWG

to 6 AWG copper conductor is required for U.S. installations. Commercially available 8-24 AWG wire

is recommended. The length of the grounding wire depends on the proximity of the switch to proper

grounding facilities.

•No. 1 Phillips screwdriver.

•Crimping tool to crimp the grounding wire to the grounding lug.

•Wire-stripping tool to remove the insulation from the grounding wire.

Cisco Catalyst 9500 Series Switches Hardware Installation Guide

Switch Installation

Required Tools and Equipment

Connecting the System Ground

To establish an earth ground for the chassis, you must attach a grounding cable from the chassis’grounding

lug to the rack.

Figure 1: Connecting the System Ground

Procedure

Step 1 Use a wire-stripping tool to remove approximately 0.75 inch (19 mm) of the covering from the end of the

grounding wire.

Step 2 Insert the stripped end of the grounding wire into the open end of the grounding lug.

Step 3 Crimp the grounding wire in the barrel of the grounding lug. Verify that the ground wire is securely attached

to the ground lug.

Step 4 Place the grounding wire lug against the grounding pad, making sure that there is solid metal-to-metal contact.

Step 5 Secure the grounding lug to the chassis with two M4 screws. Ensure that the grounding lug and the grounding

wire will not interfere with other switch hardware or rack equipment.

Step 6 Prepare the other end of the grounding wire with a ring lug, and secure it to the rack with a screw.

Installing the Switch

Rack-Mounting

Installation in racks other than 19-inch racks requires a bracket kit not included with the switch.

Cisco Catalyst 9500 Series Switches Hardware Installation Guide

Switch Installation

Connecting the System Ground

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions

to ensure that the system remains stable. The following guidelines are provided to ensure your safety:

Warning

•This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

•When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the

heaviest component at the bottom of the rack.

•If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing

the unit in the rack.

Statement 1006

This figure shows the standard 19-inch brackets and other optional mounting brackets. You can order the

optional brackets from your Cisco sales representative.

Figure 2: Rack-Mounting Brackets

Cisco Catalyst 9500 Series Switches Hardware Installation Guide

Switch Installation

Rack-Mounting

23-inch brackets319-inch brackets1

Extension rails and brackets for

four-point mounting, includes 19-inch

brackets.

Cisco Catalyst 9500 Series Switches Hardware Installation Guide

Switch Installation

Rack-Mounting

Attaching the Rack-Mount Brackets

Procedure

Use four Phillips flat-head screws to attach the long side of the bracket to each side of the switch for the front-

or rear-mounting positions.

Figure 3: Attaching 19-inch Rack Mounting Brackets

Figure 4: Attaching 23-inch Rack Mounting Brackets

Cisco Catalyst 9500 Series Switches Hardware Installation Guide

Switch Installation

Rack-Mounting

Figure 5: Front, Middle and Rear Mounting positions of Rack Mounting Brackets

Cisco Catalyst 9500 Series Switches Hardware Installation Guide

Switch Installation

Rack-Mounting

Mounting the Switch a Rack

Procedure

Step 1 Use the Phillips machine screws to attach the brackets and the extension rail to the switch.

Figure 6: Attaching the Extension Rail

Cisco Catalyst 9500 Series Switches Hardware Installation Guide

Switch Installation

Rack-Mounting

Autres manuels pour Catalyst 9500 Series

Table des matières

Autres manuels Cisco Changer

Cisco

Cisco Catalyst X4232 Guide rapide

Cisco

Cisco Linksys SE1500 Manuel utilisateur

Cisco

Cisco 4900M - Catalyst Switch Manuel utilisateur

Cisco

Cisco Cisco mds 9124 - fabric switch Manuel utilisateur

Cisco

Cisco Catalyst X4424 Manuel utilisateur

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Manuel utilisateur

Cisco

Cisco SLM224G4S Mode d’emploi

Cisco

Cisco WS X4148 RJ21 - Catalyst 4000 Series 10/100 Telco... Manuel utilisateur

Cisco

Cisco SFS 3012R Manuel

Cisco

Cisco Catalyst 2960 Series Manuel utilisateur

Cisco

Cisco Catalyst Blade Switch 3130 Manuel

Cisco

Cisco 3524-PWR - Catalyst XL Enterprise Edition... Manuel utilisateur

Cisco

Cisco Catalyst 3550 Manuel utilisateur

Cisco

Cisco Catalyst 3560-CX Manuel utilisateur

Cisco

Cisco Catalyst 1900 Series Manuel utilisateur

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manuel d'installation et d'exploitation

Cisco

Cisco Catalyst Series Switch 2940 Guide d'installation

Cisco

Cisco Cisco Small Business Unmanaged Switch SR224 Manuel utilisateur

Cisco

Cisco Nexus 5548P Manuel utilisateur

Cisco

Cisco Catalyst 3750 Metro Manuel d'installation

Cisco

Cisco Catalyst 2810 Series Manuel utilisateur

Cisco

Cisco 4006 - Catalyst Switch Mode d’emploi

Cisco

Cisco IE 3010 Manuel utilisateur

Cisco

Cisco Small Business 200 Mode d’emploi

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur