Cisco Catalyst 3560 Manuel utilisateur

Catalyst 3560 Switch Getting Started Guide

INCLUDING LICENSE AND WARRANTY

1About this Guide

2Taking Out What You Need

3Running Express Setup

4Managing the Switch

5Installing the Switch

6Connecting to the Switch Ports

7In Case of Difficulty

8Obtaining Documentation

9Documentation Feedback

10 Cisco Product Security Overview

11 Product Alerts and Field Notices

12 Obtaining Technical Assistance

13 Obtaining Additional Publications and Information

14 Cisco Limited Lifetime Hardware Warranty Terms

1About this Guide

This guide provides instructions on how to use Express Setup to configure your Catalyst switch. Also

covered are switch management options, basic rack-mounting procedures, port and module

connections, power connection procedures, and troubleshooting help.

For additional installation and configuration information for Catalyst 3560 switches, see the

Catalyst 3560 documentation on Cisco.com. For system requirements, important notes, limitations,

open and resolved bugs, and last-minute documentation updates, see the release notes, also on

Cisco.com.

When using the online publications, refer to the documents that match the Cisco IOS software version

running on the switch. The software version is on the Cisco IOS label on the switch rear panel.

You can order printed copies of the manuals from the Cisco.com sites and from the telephone numbers

listed in the “Obtaining Documentation” section on page 26.

For translations of the warnings that appear in this publication, see the Regulatory Compliance and

Safety Information for the Catalyst 3560 Switch that accompanies this guide.

2Taking Out What You Need

Follow these steps:

1. Unpack and remove the switch and the accessory kit from the shipping box.

2. Return the packing material to the shipping container, and save it for future use.

3. Verify that you have received the items shown on page 3. If any item is missing or damaged,

contact your Cisco representative or reseller for instructions. Some switch models might include

additional items that are not shown on page 3.

Equipment That You Supply to Run Express Setup

You need to supply this equipment to run Express Setup:

•PC

•Ethernet (Category 5) straight-through cable (as shown)

Shipping Box Contents (All Catalyst 3560 Switches Except the

Catalyst 3560-8PC Switch)

Regulatory Compliance

and Safety Information

for the

Catalyst 3560 Switch

Getting Started Guide

Cisco

Product Ownership

Registration card

Catalyst 3560 switch

Console cable

Two 19-inch

mounting brackets

Four number-12 Phillips machine screws

Four number-8 Phillips truss-head screws

Six number-8 Phillips flat-head screws

Four rubber mounting feet

AC power cord

Connector cover for redundant

power system (RPS)

Two number-4 pan-head screws

Cable guide

One black Phillips machine screw

Documentation

Catalyst 3560G

SERIES

PoE-48

SYST

RPS

STAT

DUPLX

SPEED

PoE

MODE

12 56

910 11 12 13 14 15 16

15X

16X

17 18 21 22 23 24 25 26 27 28 29 30 31 32

19 20

17X

18X

31X

32X

33 34 37 38 39 40 41 42 43 44 45 46 47 48

35 36

33X

34X

47X

48X

Shipping Box Contents (only the Catalyst 3560-8PC Switch)

Catalyst 3560 switch

Three number-8

Phillips pan-head screws

Regulatory Compliance

and Safety Information

for the

Catalyst 3560 Switch

Getting Started Guide

Cisco

Product Ownership

Registration card

Console cable

Four rubber mounting feet

AC power cord

(AC-powered switches only)

Screw template

Mounting magnet

Documentation

Catalyst 3560

SERIES

PoE-8

PoE

SPD

DPLX

STAT

SYST

MODE

CONSOLE 1x 2x 3x 4x 5x 6x 7x 8x

3Running Express Setup

When you first set up the switch, you should use Express Setup to enter the initial IP information. This

enables the switch to connect to local routers and the Internet. You can then access the switch through

the IP address for further configuration.

To run Express Setup:

Step 1 Make sure that nothing is connected to the switch.

During Express Setup, the switch acts as a DHCP server. If your PC has a static IP address,

change your PC settings before you begin to temporarily use DHCP.

Step 2 Power the switch by connecting the supplied AC power cord to the switch power

connector and to a grounded AC outlet.

Step 3 When the switch powers on, it begins the power-on self-test (POST). During POST, the

LEDs blink while tests verify that the switch functions properly.

Wait for the switch to complete POST, which can take several minutes.

Step 4 Verify that POST has completed by confirming that the SYST LED remains green. If the

switch fails POST, the SYST LED turns amber.

POST errors are usually fatal. Contact your Cisco technical support representative if your

switch fails POST.

Step 5 Press and hold the Mode button for

3 seconds. When all of the LEDs left

of the Mode button turn green,

release the Mode button.

If the LEDs left of the Mode button

begin to blink after you press the

button, release it. Blinking LEDs

mean that the switch has already

been configured and cannot go into

Express Setup mode. For more

information, see the “Resetting the

Switch” section on page 24.

Step 6 Verify that the switch is in Express Setup mode by confirming that all LEDs left of the

Mode button are green. (On some models, the RPS and PoE LEDs remain off.)

SYST

RPS

STAT

DUPLX

SPEED

PoE

MODE

125678

910

11 12 13 14 15 16

15X

16X

Mode button

Step 7 Connect a Category 5 Ethernet cable

to any 10/100 or 10/100/1000

Ethernet port on the switch front

panel.

Connect the other end of the cable to

the Ethernet port on your PC.

Step 8 Verify that the LEDs on both Ethernet ports are green.

Wait 30 seconds.

Step 9 Start a web browser on your PC.

Enter the IP address 10.0.0.1 in the

web browser, and press Enter.

The Express Setup page appears. If it does not appear, see the “In Case of Difficulty”

section on page 23 for help.

DHCP-enabled PC

Catalyst 3560G

SERIES

PoE-48

SYST

RPS

STAT

DUPLX

SPEED

PoE

MODE

12 56

910 11 12 13 14 15 16

15X

16X

17 18 21 22 23 24 25 26 27 28 29 30 31 32

19 20

17X

18X

31X

32X

33 34 37 38 39 40 41 42 43 44 45 46 47 48

35 36

33X

34X

47X

48X

Step 10 Enter this information in the Network Settings fields:

•In the Management Interface (VLAN ID) field, the default is 1. Enter a new VLAN ID

only if you want to change the management interface through which you manage the

switch. The VLAN ID range is 1 to 1001.

•In the IP Address field, enter the IP address of the switch. In the IP Subnet Mask field,

click the drop-down arrow, and select an IP Subnet Mask.

•In the Default Gateway field, enter the IP address for the default gateway (router).

•Enter your password in the Switch Password field. The password can be from 1 to 25

alphanumeric characters, can start with a number, is case sensitive, allows embedded

spaces, but does not allow spaces at the beginning or end. In the Confirm Switch

Password field, enter your password again.

Step 11 (Optional) You can enter the Optional Settings information now or enter it later by using

the device manager interface:

•In the Host Name field, enter a name for the switch. The host name is limited to 31

characters. Embedded spaces are not allowed.

•Enter the date, time, and time zone information in the System Date,System Time, and

Time Zone fields. Click Enable to enable daylight saving time.

Step 12 (Optional) Click the Advanced Settings tab on the Express Setup window, and enter the

advanced settings now or enter them later by using the device manager interface.

Step 13 (Optional) Enter this information in the Advanced Setting fields:

•In the Telnet Access field, click Enable if you are going to use Telnet to manage the

switch by using the command-line interface (CLI). If you enable Telnet access, you

must enter a Telnet password.

•In the Telnet Password field, enter a password. The Telnet password can be from 1 to

25 alphanumeric characters, is case sensitive, allows embedded spaces, but does not

allow spaces at the beginning or end. In the Confirm Telnet Password field, re-enter

the Telnet password.

•In the SNMP field, click Enable to enable Simple Network Management Protocol

(SNMP). Enable SNMP only if you plan to manage switches by using

CiscoWorks 2000 or another SNMP-based network-management system.

•If you enable SNMP, you must enter a community string in the SNMP Read

Community field, the SNMP Write Community field, or both. SNMP community

stringsauthenticateaccesstoMIBobjects.EmbeddedspacesarenotallowedinSNMP

community strings. When you set the SNMP read community, you can access SNMP

information, but you cannot modify it. When you set the SNMP write community,

you can both access and modify SNMP information.

•In the System Contact and System Location fields, enter a contact name and the wiring

closet, floor, or building where the switch is located.

Step 14 (Optional) You can enable Internet Protocol version 6 (IPv6) on the switch. From the

Advanced Settings tab, check the Enable IPv6 check box.

Note Enabling IPv6 restarts the switch when you complete Express Setup.

Step 15 To complete Express Setup, click Submit from the Basic Settings or the Advanced Settings

tab to save your settings, or click Cancel to clear your settings.

When you click Submit, the switch is configured and exits Express Setup mode. The PC

displays a warning message and tries to connect with the new switch IP address. If you

configured the switch with an IP address that is in a different subnet from the PC,

connectivity between the PC and the switch is lost.

Step 16 Disconnect the switch from the PC, and install the switch in your production network. See

the “Managing the Switch” section on page 9 for information about configuring and

managing the switch.

If you need to rerun Express Setup, see the “Resetting the Switch” section on page 24.

Refreshing the PC IP Address

After you complete Express Setup, you should refresh the PC IP address.

For a dynamically assigned IP address, disconnect the PC from the switch, and reconnect it to the

network. The network DHCP server assigns a new IP address to the PC.

For a statically assigned IP address, change it to the previously configured IP address.

4Managing the Switch

After completing Express Setup and installing the switch in your network, use the device manager or

other management options described in this section for further configuration.

Using the Device Manager

You can manage the switch by using the device manager that is in the switch memory. This is a web

interface that offers quick configuration and monitoring. You can access the device manager from

anywhere in your network through a web browser.

Follow these steps:

1. Start a web browser on your PC or workstation.

2. Enter the switch IP address in the web browser, and press Enter. The device manager page appears.

3. Use the device manager to perform basic switch configuration and monitoring. Refer to the device

manager online help for more information.

4. For more advanced configuration, install Cisco Network Assistant as described in the next section.

Downloading Cisco Network Assistant

Cisco Network Assistant is a free software program that you download from Cisco.com and run on

your PC. Network Assistant offers advanced options for configuring and monitoring multiple devices,

including switches, switch clusters, switch stacks, routers, and access points. Network Assistant is

free—there is no charge to download, install, or use it.

Follow these steps:

1. Go to this Web address: http://www.cisco.com/go/NetworkAssistant

You must be a registered Cisco.com user, but you need no other access privileges.

2. Find the Network Assistant installer.

3. Download the Network Assistant installer, and run it. (You can run it directly from the Web if

your browser offers this choice.)

4. When you run the installer, follow the displayed instructions. In the final panel, click Finish to

complete the Network Assistant installation.

Refer to the Network Assistant online help and the getting started guide for more information.

Command-Line Interface

You can enter Cisco IOS commands and parameters through the CLI. Access the CLI either by

connecting your PC directly to the switch console port or through a Telnet session from a remote PC

or workstation.

Follow these steps:

1. Connect the supplied RJ-45-to DB-9 adapter cable to the standard 9-pin serial port on the PC.

Connect the other end of the cable to the console port on the switch.

2. Start a terminal-emulation program on the PC.

3. Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit,

and no flow control.

4. Use the CLI to enter commands to configure the switch. See the software configuration guide and

the command reference for more information.

Other Management Options

You can use SNMP management applications such as CiscoWorks Small Network Management

Solution (SNMS) and HP OpenView to configure and manage the switch. You also can manage it from

an SNMP-compatible workstation that is running platforms such as HP OpenView or SunNet

Manager.

The Cisco IE2100 Series Configuration Registrar is a network management device that works with

embedded CNS agents in the switch software. You can use IE2100 to automate initial configurations

and configuration updates on the switch.

See the “Accessing Help Online” section on page 24 for a list of supporting documentation.

Autres manuels pour Catalyst 3560

Table des matières

Autres manuels Cisco Changer

Cisco

Cisco AP775A - Nexus Converged Network Switch 5010 Mode d’emploi

Cisco

Cisco Catalyst 3560E-24TD Dimensions

Cisco

Cisco ME-3600X-24CX Series Manuel utilisateur

Cisco

Cisco CSS 11501 - Content Services Switch Manuel utilisateur

Cisco

Cisco Nexus 1110-S Guide de référence rapide

Cisco

Cisco SLM2024 - Small Business Smart Switch Manuel utilisateur

Cisco

Cisco Catalyst 3560E-12SD Dimensions

Cisco

Cisco Catalyst 6500-E Series Manuel utilisateur

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manuel d'installation et d'exploitation

Cisco

Cisco VCO/4K Manuel utilisateur

Cisco

Cisco Catalyst 3560-E Series Manuel utilisateur

Cisco

Cisco Gigabit Switch Router Cisco 12012 Mode d’emploi

Cisco

Cisco Catalyst 3850 series Manuel utilisateur

Cisco

Cisco Catalyst 3120 Guide de démarrage rapide

Cisco

Cisco SF250-24-K9 Manuel utilisateur

Cisco

Cisco Catalyst 3560-CX Manuel utilisateur

Cisco

Cisco MGX 8950 Manuel utilisateur

Cisco

Cisco Nexus 5596 Manuel

Cisco

Cisco 5509 - Catalyst Chassis Switch Manuel utilisateur

Cisco

Cisco 6509 - Catalyst Chassis Switch Manuel utilisateur

Cisco

Cisco WS-C2960L-24TS-LL Manuel utilisateur

Cisco

Cisco SG 300-10 Manuel utilisateur

Cisco

Cisco Nexus 9000 Series Manuel utilisateur

Cisco

Cisco MGX 8950 Instructions d'utilisation et de sécurité

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur