Cisco 861W - Integrated Services Router Wireless Manuel utilisateur

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco Configuration Professional

Quick Start Guide

April 29, 2011

This document explains how to start using Cisco Configuration Professional Express

(Cisco CP Express) and Cisco Configuration Professional (Cisco CP).

Cisco Configuration Professional (Cisco CP) is a GUI based device management tool for Cisco access

routers. This tool simplifies routing, firewall, IPS, VPN, unified communications, WAN and LAN

configuration through GUI based easy-to-use wizards.

Cisco CP is a valuable productivity enhancing tool for network administrators and channel partners for

deploying routers with increased confidence and ease. It offers a one-click router lockdown and an

innovative voice and security auditing capability to check and recommend changes to router

configuration. Cisco CP also monitors router status and troubleshoots WAN and VPN connectivity

issues.

Cisco CP Express is a light weight version of Cisco CP. You can use Cisco CP Express to configure basic

security features on the router’s LAN and WAN interfaces. Cisco CP Express is available on the router

Flash memory.

This document shows you how to set up a PC to connect to the router, give the router an initial network

configuration using Cisco CP Express, and then begin using Cisco CP.

This document is intended for users with one of the ordering options (SKU) listed in Table 1, and for

users who download these configuration tools from Cisco.com. Refer to the Release Notes for

Cisco Configuration Professional for information about supported routers, web browsers, and plug-ins.

Cisco CP ordering options are provided to suit a variety of deployments. Table 1 describes the Cisco CP

ordering options, the deployment each supports, and how this document can be used.

Cisco Configuration Professional Quick Start Guide

78-18480-08

Table 1 Cisco CP Ordering Options

ORDERING OPTION (SKU) CD and Configuration File Which Task Sections You Can Use

CCP-CD

This option lets you use

Cisco CP Express to set up

an individual router when

you receive it, and to install

Cisco CP from the CD and

begin using it.

Cisco CP CD?

Yes. The Cisco CP CD is provided.

Default Configuration File in NVRAM?

Yes. A default configuration file is in

NVRAM, so the router will have a basic

configuration with an IP address on

startup.

Default Configuration File in Flash?

Yes. The router can be set to factory

defaults using the Factory Defaults

feature in Cisco CP Express.

You can use the following task sections of this

document:

•Task 3: Configure the IP Address on the PC

•Task 4: Connect the PC to the Router

•Task 5: Run the Cisco CP Express Wizard

•Task 6: Verify the Initial Configuration

•Task 7: Install Cisco CP

•Task 8: Start Using Cisco CP

CCP-CD-NOCF

This option gives you the

flexibility of loading a

configuration on the router

by using a TFTP server or

by other means, and allows

for batch configuration. If

you start a console session,

the Setup Command Facility

starts automatically.

Cisco CP CD?

Yes. The Cisco CP CD is provided.

Default Configuration File in NVRAM?

No. If a console session is established

with the router, the Setup Command

Facility starts automatically

Default Configuration File in Flash?

Yes. The router can be set to factory

defaults using the Factory Defaults

feature in Cisco CP Express.

You can use the following task sections of this

document:

•Task 2: Configure the Router for Cisco CP

•Task 7: Install Cisco CP

•Task 8: Start Using Cisco CP

CCP-EXPRESS

This option lets you use

Cisco CP Express to set up

an individual router when

you receive it. If you want

Cisco CP, you can

download it from

www.cisco.com.

Cisco CP CD?

No. The Cisco CP CD is not provided. If

you want to use Cisco CP, you can

download it from the following page:

http://www.cisco.com/go/ciscocp

Default Configuration File in NVRAM?

Yes. A default configuration file is in

NVRAM, so the router will have a basic

configuration with an IP address on

startup.

Default Configuration File in Flash?

Yes. The router can be set to factory

defaults using the Factory Defaults

feature in Cisco CP Express.

You can use the following task sections of this

document:

•Task 1: Download the Cisco CP Files

•Task 3: Configure the IP Address on the PC

•Task 4: Connect the PC to the Router

•Task 5: Run the Cisco CP Express Wizard

•Task 6: Verify the Initial Configuration

•Task 7: Install Cisco CP

•Task 8: Start Using Cisco CP

Cisco Configuration Professional Quick Start Guide

78-18480-08

Task 1: Download the Cisco CP Files

This task section explains how to download the Cisco CP files. See the following table to determine if

you need to use this section.

To download Cisco CP, complete the following tasks:

Step 1 Open a web browser and go to the following link:

http://www.cisco.com/go/ciscocp

Step 2 In the Support box, click Download Software.

Step 3 If a web page is displayed that asks for your Cisco.com credentials, enter them in this page, and click

to this page.

Step 4 In the Download page that allows you to select a release, choose the release that you want to download.

CCP-EXPRESS-NOCF

This option gives you the

flexibility of loading a

configuration on the router

by using a TFTP server or

by other means, and allows

for batch configuration. If

you start a console session,

the Setup Command Facility

starts automatically.

Cisco CP CD?

No. The Cisco CP CD is not provided. If

you want to use Cisco CP, you can

download it from the following page:

http://www.cisco.com/go/ciscocp

Default Configuration File in NVRAM?

No. If a console session is established

with the router, the Setup Command

Facility starts automatically

Default Configuration File in Flash?

Yes. The router can be set to factory

defaults using the Factory Defaults

feature in Cisco CP Express. Cisco CP

is not shipped with the router.

You can use the following task sections of this

document:

•Task 1: Download the Cisco CP Files

•Task 2: Configure the Router for Cisco CP

•Task 7: Install Cisco CP

•Task 8: Start Using Cisco CP

Table 1 Cisco CP Ordering Options (continued)

ORDERING OPTION (SKU) CD and Configuration File Which Task Sections You Can Use

Who Should Use this Section If you did not receive the CD, but you want to install and use Cisco CP,

use this section.

Who Can Skip this Section If you received the CD, skip this section, and go to Task 2: Configure the

Router for Cisco CP.

Cisco Configuration Professional Quick Start Guide

78-18480-08

Task 2: Configure the Router for Cisco CP

Step 5 In the Download page for the release that you chose, click the link Cisco-config-pro-k9-pkg-N_N-ln.zip

to download Cisco CP. In this filename, N_N represents the version number and ln represents the

language. If you wanted English-language Cisco CP 1.1, you would click on the link

Cisco-config-pro-k9-pkg-1_1-en.zip.

Step 6 Save the downloaded file to the PC.

This package will be used in Task 7: Install Cisco CP, page 20.

Task 2: Configure the Router for Cisco CP

This task section explains how to configure the router to support Cisco CP Express and Cisco CP.

Note The tasks that follow can also be accomplished using the Application > Setup New Device option in

Cisco CP by connecting the PC to the console port of the device. See the topic Device Wizard in the

Cisco Configuration Professional User Guide 2.5 at

http://www.cisco.com/en/US/products/ps9422/products_user_guide_list.html for more details.

Note Make sure that the PC on which Cisco CP Express and Cisco CP is installed can connect to the router

using its IP address.

Cisco CP Express and Cisco CP require the following basic configuration in order to connect to the

router and manage it.

•An http or https server must be enabled with local authentication.

•A local user account with privilege level 15 and accompanying password must be configured.

•Vty line with protocol ssh/telnet must be enabled with local authentication. This is needed for

interactive commands.

•An http timeout policy must be configured with the parameters shown in the following procedure to

avoid a known launch issue with Cisco CP.

•The PC on which Cisco CP is to run and the interface through which Cisco CP will be launched must

be configured with IP addresses from the same subnet.

There are two ways that you can ensure that the router configuration meets these requirements:

•You can copy the default configuration file from router Flash memory to router NVRAM. Each

ordering option provides the default configuration file in router Flash memory. To use this method,

see Copying the Default Configuration File to Router NVRAM.

Who Should Use this Section If your ordering option does not include a configuration file in NVRAM,

and you want to use Cisco CP Express or Cisco CP, use this section.

Who Can Skip this Section If your ordering option includes a configuration file in NVRAM, you can

skip this section. The router is configured to support Cisco CP Express and

Cisco CP.

Cisco Configuration Professional Quick Start Guide

78-18480-08

Task 2: Configure the Router for Cisco CP

•You can use the Cisco IOS CLI to enter the necessary configuration commands. To use this method,

see Entering the Configuration Commands Manually.

Copying the Default Configuration File to Router NVRAM

If you want to start with a factory default configuration that is designed to support Cisco CP, you can

use the procedure in this section. The factory default configuration includes all the commands necessary

to support Cisco CP and configures an Ethernet interface with the IP address 10.10.10.1.

To copy the default configuration file from router Flash memory to NVRAM, complete the following

steps.:

Step 1 Log on to the router through the Console port or through an Ethernet port.

Step 2 If you use the Console port, and no running configuration is present in the router, the Setup command

Facility starts automatically, and displays the following text:

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]:

Enter no so that you can enter Cisco IOS CLI commands directly.

If the Setup Command Facility does not start automatically, a running configuration is present, and you

should go to the next step.

Step 3 When the router displays the user EXEC mode prompt, enter the enable command, and the enable

password, if one is configured, as shown below:

Router> enable

password password

Router#

Step 4 To identify the default configuration file, enter the show flash command. The filename is of the form

cpconfig-modelnumber.cfg, where modelnumber represents the router series. For example the

configuration file name for the Cisco 860 and 880 series routers is cpconfig-8xx.cfg.

Router# show flash

-#- --length-- -----date/time------ path

1 2903 Apr 15 2008 20:34:48 +00:00 cpconfig-8xx.cfg

2 115712 Apr 15 2008 20:34:50 +00:00 home.tar

3 2279424 Apr 15 2008 20:34:54 +00:00 cpexpress.tar

Router#

Step 5 To copy the default configuration file to router NVRAM, enter the copy flash: nvram: command, as

shown in the following example:

Router# copy flash:cpconfig-8xx.cfg nvram:

When the default configuration file is in NVRAM, it becomes the router startup configuration.

Step 6 To make the new startup configuration the running configuration, so that the router can support Cisco

CP, enter the copy startup-config running-config command, as shown in the following example:

Router# copy startup-config running-config

Cisco Configuration Professional Quick Start Guide

78-18480-08

Task 2: Configure the Router for Cisco CP

Entering the Configuration Commands Manually

If you don’t want to use the factory default configuration because the router already has a configuration,

or for any other reason, you can use the procedure in this section to add each required command to the

configuration.

To enter the Cisco IOS commands manually, complete the following steps:

Step 1 Log on to the router through the Console port or through an Ethernet port.

Step 2 If you use the Console port, and no running configuration is present in the router, the Setup command

Facility starts automatically, and displays the following text:

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]:

Enter no so that you can enter Cisco IOS CLI commands directly.

If the Setup Command Facility does not start automatically, a running configuration is present, and you

should go to the next step.

Step 3 When the router displays the user EXEC mode prompt, enter the enable command, and the enable

password, if one is configured, as shown in the following example:

Router> enable

password password

Step 4 Enter config mode by entering the config terminal command, as shown in the following example.

Router> config terminal

Router(config)#

Step 5 Using the command syntax shown, create a user account with privilege level 15.

Router(config)# username name privilege 15 secret 0 password

Step 6 If no router interface is configured with an IP address, configure one so that you can access the router

over the network. The following example shows the interface Fast Ethernet 0 configured.

Router(config)# int FastEthernet0

Router(config-if)# ip address 10.10.10.1 255.255.255.248

Router(config-if)# no shutdown

Router(config-if)# exit

If you are going to connect the PC directly to the router, the PC must be on the same subnet as this

interface.

Step 7 Configure the router as an http server for nonsecure communication, or as an https server for secure

communication.

To configure the router as an http server, enter the ip http server command shown in the example:

Router(config)# ip http server

To configure the router as an https server, enter the ip http secure-server command shown in the

example:

Router(config)# ip http secure-server

Step 8 Configure the router for local authentication, by entering the ip http authentication local command, as

shown in the example:

Router(config)# ip http authentication local

Cisco Configuration Professional Quick Start Guide

78-18480-08

Configure the Switch for Cisco CP

Step 9 Configure the http timeout policy as shown in the example:

Router(config)# ip http timeout-policy idle 60 life 86400 requests 10000

Step 10 Configure the vty lines for privilege level 15. For nonsecure access, enter the transport input telnet

command. For secure access, enter the transport input telnet ssh command. An example of these

commands follows:

Router(config)# line vty 0 4

Router(config-line)# privilege level 15

Router(config-line)# login local

Router(config-line)# transport input telnet

Router(config-line)# transport output telnet

Router(config-line)# transport input telnet ssh

Router(config-line)# transport output telnet ssh

Router(config-line)# exit

Router(config)# line vty 5 15

Router(config-line)# privilege level 15

Router(config-line)# login local

Router(config-line)# transport input telnet

Router(config-line)# transport output telnet

Router(config-line)# transport input telnet ssh

Router(config-line)# transport output telnet ssh

Router(config-line)# end

Configure the Switch for Cisco CP

This task section explains how to configure the switch to support Cisco CP.

Note The tasks that follow can also be accomplished using the Application > Setup New Device option in

Cisco CP by connecting the PC to the console port of the device. See the topic Device Wizard in the

Cisco Configuration Professional User Guide 2.5 at

http://www.cisco.com/en/US/products/ps9422/products_user_guide_list.html for more details.

Note Make sure that the PC on which Cisco CP is installed can connect to the switch using its IP address.

Cisco CP require the following basic configuration in order to connect to the switch and manage it.

•An http or https server must be enabled with local authentication.

•A local user account with privilege level 15 and accompanying password must be configured.

•Vty line with protocol ssh/telnet must be enabled with local authentication. This is needed for

interactive commands.

•An http timeout policy must be configured with the parameters shown in the following procedure to

avoid a known launch issue with Cisco CP.

•The PC on which Cisco CP is to run and the interface through which Cisco CP will be launched must

be configured with IP addresses from the same subnet.

You can use the Cisco IOS CLI to enter the necessary configuration commands. To use this method, see

Entering the Configuration Commands Manually.

Cisco Configuration Professional Quick Start Guide

78-18480-08

Configure the Switch for Cisco CP

Entering the Configuration Commands Manually

To enter the Cisco IOS commands manually, complete the following steps:

Step 1 Log on to the switch through the Console port or through an Ethernet port.

Step 2 If you use the Console port, and no running configuration is present in the switch, the Setup command

Facility starts automatically, and displays the following text:

---System Configuration Dialog---

Continue with configuration dialog? [yes/no]:

Enter no so that you can enter Cisco IOS CLI commands directly.

If the Setup Command Facility does not start automatically, a running configuration is present, and you

should go to the next step.

Step 3 When the switch displays the user EXEC mode prompt, enter the enable command, and the enable

password, if one is configured, as shown in the following example:

Switch> enable

password password

Step 4 Enter config mode by entering the config terminal command, as shown in the following example.

Switch> config terminal

Switch(config)#

Step 5 Using the command syntax shown, create a user account with privilege level 15.

Switch(config)# username name privilege 15 secret 0password

Step 6 If IP Address is not configured, configure one so that you can access the switch over the network. The

following example shows the IP Address configured on interface Vlan1.

Switch(config)# interface Vlan1

Switch(config-if)# ip address 10.10.10.1 255.255.255.248

Switch(config-if)# no shutdown

Switch(config-if)# exit

If you are going to connect the PC directly to the switch, the PC must be on the same subnet as this

interface.

Step 7 Configure the switch as an http server for nonsecure communication, or as an https server for secure

communication.

To configure the switch as an http server, enter the ip http server command shown in the example:

Switch(config)# ip http server

To configure the switch as an https server, enter the ip http secure-server command shown in the

example:

Switch(config)# ip http secure-server

Step 8 Configure the switch for local authentication, by entering the ip http authentication local command, as

shown in the example:

Switch(config)# ip http authentication local

Step 9 Configure the http timeout policy as shown in the example:

Switch(config)# ip http timeout-policy idle 60 life 86400 requests 10000

Cisco Configuration Professional Quick Start Guide

78-18480-08

Task 3: Configure the IP Address on the PC

Step 10 Configure the vty lines for privilege level 15. For nonsecure access, enter the transport input telnet

command. For secure access, enter the transport input telnet ssh command. An example of these

commands follows:

Switch(config)# line vty 0 4

Switch(config-line)# privilege level 15

Switch(config-line)# login local

Switch(config-line)# transport input telnet

Switch(config-line)# transport output telnet

Switch(config-line)# transport input telnet ssh

Switch(config-line)# transport output telnet ssh

Switch(config-line)# exit

Switch(config)# line vty 5 15

Switch(config-line)# privilege level 15

Switch(config-line)# login local

Switch(config-line)# transport input telnet

Switch(config-line)# transport output telnet

Switch(config-line)# transport input telnet ssh

Switch(config-line)# transport output telnet ssh

Switch(config-line)# end

Task 3: Configure the IP Address on the PC

This task section explains how to configure an IP address on the PC so that you can connect to

Cisco CP Express and begin configuring the router.

The default configuration file assigns an IP address to a LAN interface on the router, and you must

configure the PC to be on the same subnet as the router LAN interface. If the router is a fixed-interface

model, it is configured as a DHCP server, and the PC must be configured to accept an IP address

automatically. If the router can accept modular interfaces, it is not configured as a DHCP server, and you

must configure the PC with a static IP address on the same subnet as the router.

To configure the IP address on the PC, complete the following steps:

Step 1 Find your router model number in Table 2. Note the required IP address configuration for the PC.

Note If the router model you want to configure does not appear in Table 2, see the Release Notes for

Cisco Configuration Professional for updated information.

Who Should Use this Section If you are setting up a new router, and want to use Cisco CP Express to

give the router a basic configuration, use this section.

Who Can Skip this Section If you don’t want to use Cisco CP Express to give the router a basic

configuration, you can skip this section.

Cisco Configuration Professional Quick Start Guide

78-18480-08

Task 3: Configure the IP Address on the PC

Step 2 Configure the IP address on the PC.

If the PC runs Microsoft Windows XP, complete the following steps to display the Internet Protocol

TCP/IP Properties dialog:

a. Click Start > Control Panel > Network Connections > Local Area Connection.

b. In the item list, select Internet Protocol (TCP/IP).

c. Click Properties.

d. Go to Step 3.

If the PC runs Microsoft Windows Vista, complete the following steps to display the Internet Protocol

TCP/IP Properties dialog:

a. Click Start > Control Panel > Network and Sharing Center.

b. In the Tasks column on the left, click Manage network connections.

c. In the Network Connections screen, click Local Area Connection.

d. In the Networking tab of the Local Area Connection Properties dialog, select Internet Protocol

Version 4, and click Properties.

e. Go to Step 3.

Table 2 Required PC IP Address Configurations

Router Model DHCP Server Required PC IP Address Configuration

Cisco 815, Cisco 85x, Cisco 86x, Cisco

87x, Cisco 88x, Cisco 891, Cisco 892,

Cisco 180x, Cisco 1805, Cisco 1811 and

1812

Yes Obtain an IP address automatically.

Cisco 1841, Cisco 1861, Cisco 28xx,

Cisco 38xx

No Static IP address from 10.10.10.2 to

10.10.10.6

Subnet Mask: 255.255.255.248

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Logiciel

Cisco

Cisco TELEPRESENCE MANAGEMENT SUITE SECURE SERVER - CONFIGURATION GUIDE... Manuel utilisateur

Cisco

Cisco TELEPRESENCE MANAGEMENT SUITE EXTENSION 2.2 - FOR MICROSOFT... Manuel utilisateur

Cisco

Cisco Cisco Access Registrar 4.2 Manuel de l'opérateur

Cisco

Cisco GO GREEN Manuel utilisateur

Cisco

Cisco 1701 Mode d’emploi

Cisco

Cisco TELEPRESENCE MOVI 4.1 - ADMINISTRATOR GUIDE... Manuel de service

Cisco

Cisco 6.x and 7.0 Guide de démarrage rapide

Cisco

Cisco 3.3 Manuel utilisateur

Cisco

Cisco 5520 - ASA IPS Edition Bundle Manuel utilisateur

Cisco

Cisco TMS SQL DATABASE Manuel utilisateur

Cisco

Cisco CSACSE-1111-K9 - Secure Access Control Server Solution... Manuel utilisateur

Cisco

Cisco TELEPRESENCE CALL DETAIL RECORDS FILE FORMAT... Manuel utilisateur

Cisco

Cisco TELEPRESENCE MOVI 4.1 - FOR MAC OS X Manuel utilisateur

Cisco

Cisco WS-SUP32-GE-3B - Supervisor Engine 32 Manuel utilisateur

Cisco

Cisco TELEPRESENCE MANAGEMENT SUITE SECURE SERVER - CONFIGURATION GUIDE... Manuel utilisateur

Cisco

Cisco CISCO1811 Manuel utilisateur

Cisco

Cisco CCNA NETWORK SIMULATOR Manuel utilisateur

Cisco

Cisco Unified Videoconferencing Manager Manuel utilisateur

Cisco

Cisco MeetingPlace Video Integration Manuel de service

Cisco

Cisco CRS-1 Series Manuel utilisateur

Cisco

Cisco ASA5500-SC-5= - ASA 5500 Security Context Manuel utilisateur

Cisco

Cisco Router IOS XR Manuel utilisateur

Cisco

Cisco MCS 7825 Series Manuel utilisateur

Cisco

Cisco Digital Media System 3.5 Mode d’emploi

Manuels Logiciel populaires d'autres marques

COMPRO

COMPRO COMPROFM Manuel utilisateur

Muratec

Muratec OFFICEBRIDGE ONLINE Manuel utilisateur

Oracle

Oracle Contact Center Anywhere 8.1 Manuel utilisateur

Adobe

Adobe 65007312 - Photoshop Lightroom Manuel

Avaya

Avaya NULL One-X for RIM Blackberry Manuel utilisateur

HP ProLiant BL420c Manuel utilisateur

PS Audio

PS Audio PowerPlay Manuel du propriétaire

Brady

Brady LOCKOUT PRO 3.0 Manuel de service

Avaya

Avaya Interaction Center Manuel utilisateur

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manuel

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manuel utilisateur

Oracle

Oracle Application 9i Manuel utilisateur

Acer

Acer RDM Manuel utilisateur

Canon

Canon Vixia HF21 Manuel utilisateur

Canon

Canon ZR950 Manuel utilisateur

Samsung

Samsung Auto Backup Manuel utilisateur

Polycom

Polycom Vortex EF2201 Instructions d'installation et d'utilisation

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manuel utilisateur