Cisco Digital Media Player Manuel utilisateur

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

User Guide for Cisco Digital Media Player

Device Manager 1.0

May 17, 2007

Text Part Number: OL-12472-01

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the

document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

User Guide for Cisco Digital Media Player Device Manager 1.0

CCSP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick

Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified

Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation,

Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ

Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing,

ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO

are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (0411R)

iii

User Guide for Cisco Digital Media Player Device Manager 1.0

OL-12472-01

CONTENTS

Document Conventions v

Obtaining Documentation, Obtaining Support, and Security Guidelines vi

CHAPTER

1Introduction 1-1

Environmental Tolerances and Safety Guidelines 1-2

General Precautions 1-3

Protecting Against Electrostatic Discharge 1-4

Understanding DMP Modes of Operation 1-5

Limited Support for MPEG-4 1-5

Supported Filetypes in the Embedded Browser 1-5

Understanding the Difference Between ‘Apply’ and ‘Save’ 1-6

Understanding Content Substitution (Failover) 1-6

Preconfiguring Your DMP To Run Without a Local DHCP Server 1-6

Basic DMS Concepts and Vocabulary 1-8

CHAPTER

2Using DMPDM 2-1

Using One-Click Options for a DMP Display 2-1

Viewing the Assigned DMP IP Address 2-1

Viewing Video Content in Full-Screen Mode 2-2

Viewing HTML Content in Full-Screen Mode 2-2

Configuring Settings 2-2

Adjusting Basic Network Settings 2-2

Adjusting Embedded Browser Settings 2-4

Adjusting DMP Display Settings 2-5

Enabling or Disabling Centralized Management 2-7

Adjusting the Placement and Proportions of Content on a DMP Display 2-8

Enabling or Disabling Types of Access to Your DMP 2-9

Selecting the Content to Show 2-10

Showing or Stopping Video Content from a UDP Multicast Stream 2-10

Showing or Stopping Video Content from an HTTP URL 2-11

Showing or Stopping Video Content from a File Stored on Your DMP 2-11

Adjusting the Transparency of the HTML Content Plane 2-12

Contents

User Guide for Cisco Digital Media Player Device Manager 1.0

OL-12472-01

Specifying the URL to Show on the HTML Content Plane 2-13

Supported Fonts 2-14

Supported X11 Bitmap Fonts 2-15

Supported TrueType Fonts 2-16

Using Administrative Options 2-17

Editing the DMPDM User Account 2-17

Editing the FTP User Account 2-17

Saving Settings That You Configured 2-18

Restoring Factory Default Settings 2-18

Restarting Your DMP 2-19

Upgrading the DMP Firmware 2-19

Common Scenarios for Using DMPDM 2-20

Showing Content Files That Are Stored on the SD Card 2-20

Showing Content Files That Are Stored on a USB Flash Drive 2-20

Viewing the DMPDM ‘About Box’ 2-21

Viewing the DMP Device License Number 2-21

User Guide for Cisco Digital Media Player Device Manager 1.0

OL-12472-01

Preface

Cisco Digital Media System is the collective name for a product family that consists of Cisco Digital

Media Manager (DMM) appliances, Cisco Video Portal appliances, Cisco Digital Media Player (DMP)

endpoints, Cisco Digital Media Encoder (DME) devices, and all associated software components.

This guide describes how to use Cisco Digital Media Player Device Manager 1.0 (DMPDM) software

that is embedded on every Cisco Digital Media Player 4300G device.

The intended audience for this guide is systems or network administrators who install, configure, or

troubleshoot DMP device hardware, and anyone who owns or uses fewer than three DMPs.

Tip If you you own more than three DMPs but do not understand why you should use DMM-DSM instead

of DMPDM to manage a digital signage network, see Understanding DMP Modes of Operation, page 5.

See Cisco.com for related DMS and DMM user documentation.

Document Conventions

This guide uses these text formatting conventions:

Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the

publication.

Item Convention

Commands and keywords boldface font

Variables for which you supply values italic font

Displayed session and system information screen font

Information you enter boldface screen font

Variables you enter italic screen font

Menu items and button names boldface font

Selecting a menu item in paragraphs Option > Network Preferences

Selecting a menu item in tables Option > Network Preferences

User Guide for Cisco Digital Media Player Device Manager 1.0

OL-12472-01

Preface

Obtaining Documentation, Obtaining Support, and Security Guidelines

Caution Means reader be careful. In this situation, you might do something that could result in equipment

damage or loss of data.

Tip Means the following information will help you solve a problem. The tips information might not be

troubleshooting or even an action, but could be useful information, similar to a Timesaver.

Obtaining Documentation, Obtaining Support, and

Security Guidelines

For information on obtaining documentation, obtaining support, providing documentation feedback,

security guidelines, and also recommended aliases and general Cisco documents, see the monthly

What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical

documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

CHAPTER

1-1

User Guide for Cisco Digital Media Player Device Manager 1.0

OL-12472-01

Introduction

Revised Apr. 25, 2007

This guide describes how to use your DMP device and how to use the preinstalled DMPDM software.

DMP devices can show networked digital video streams and multicast, high-quality MPEG video on any

television receiver or monitor (NTSC, PAL, LCD, plasma, or VGA) that you attach.

Tip To learn what other filetypes your DMP can render, see Supported Filetypes in the Embedded Browser,

page 1-5.

DMPDM helps you to deliver compelling digital media to one DMP display for many possible purposes:

•Marketing—Describe products and services directly to your in-store customers.

•Customer experience— Deliver entertainment and information to reduce perceived wait times.

•Messaging—Broadcast executive and internal communications in real time.

•Training —Deliver cost-effective, flexible training.

•Information—Deliver real-time schedules, news, and way-faring information where people need it.

•Advertising— Sell advertising time and space to third parties.

•Branding— Communicate about your brand consistently.

This guide assumes that you already completed the procedures in Quick Start Guide for Cisco Digital

Media Player 4300G and therefore all of the following are true:

•Your DMP is connected to:

–

A network with a DHCP server.

–

A DMP display.

–

A 120V AC electrical socket.

•You already:

–

Checked the LEDs to confirm that your DMP has power and has obtained an IP address.

–

Learned what dynamic IP address the DHCP server assigned to your DMP.

–

Used your browser to log in to the DMPDM administrative account.

–

Used DMPDM to configure video output settings for the DMP display.

–

(Optional) Used DMPDM to identify the one trusted DMM appliance from which your DMP

should accept centralized management instructions and file transfers.

1-2

User Guide for Cisco Digital Media Player Device Manager 1.0

OL-12472-01

Chapter 1 Introduction

Environmental Tolerances and Safety Guidelines

If any of the preceding is not yet true for you, we recommend that you obtain Quick Start Guide for

Cisco Digital Media Player 4300G and complete all of the procedures in it before you use this guide.

This introduction contains the following sections:

•Environmental Tolerances and Safety Guidelines, page 1-2

•Understanding DMP Modes of Operation, page 1-5

•Limited Support for MPEG-4, page 1-5

•Supported Filetypes in the Embedded Browser, page 1-5

•Understanding the Difference Between ‘Apply’ and ‘Save’, page 1-6

•Preconfiguring Your DMP To Run Without a Local DHCP Server, page 1-6

•Basic DMS Concepts and Vocabulary, page 1-8

Environmental Tolerances and Safety Guidelines

Caution Your DMP might malfunction or be severly damaged if the temperature drops too low or climbs too high

at the physical location where you deploy it, or if other environmental tolerances are exceeded.

Table 1-1 describes environmental tolerance ranges for a DMP 4300G.

Table 1-1 DMP 4300G Environmental Tolerance Ranges

Environmental Characteristics Tolerance Ranges and Levels

Temperature, ambient US Customary Unit Modern Metric Unit

Minimum Maximum Minimum Maximum

Operating, long-term or short-term 41°F 104°F 5°C 40°C

Nonoperating or storage –4°F 140°F –20°C 60°C

Humidity, relative (noncondensing; ambient) Minimum Maximum

Operating, nonoperating, and storage 20 percent 85 percent

Altitude (above sea level) US Customary Unit Modern Metric Unit

Minimum Maximum Minimum Maximum

Operating, nonoperating, and storage 0 feet 13,780 feet 0 meters 4,200 meters

1-3

User Guide for Cisco Digital Media Player Device Manager 1.0

OL-12472-01

Chapter 1 Introduction

Environmental Tolerances and Safety Guidelines

Warning

The device is designed to work with TN power systems.

The power supply must be placed indoors.

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Read the installation instructions before connecting the system to the power source.

This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that

the protective device is rated not greater than: 120 VAC, 15A U.S. (240 VAC, 10A international)

The plug-socket combination must be accessible at all times, because it serves as the main

disconnecting device.

To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network

voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some

LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.

Installation of the equipment must comply with local and national electrical codes.

This equipment is intended to be grounded. Ensure that the host is connected to an earth ground

during normal use.

When installing the unit, always make the ground connection first and disconnect it last.

Ultimate disposal of this product should be handled according to all national laws and regulations.

To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment, observe the

following precautions.

•General Precautions, page 1-3

•Protecting Against Electrostatic Discharge, page 1-4

General Precautions

Observe the following general precautions for using and working with your system:

•Observe and follow service markings. Do not service any Cisco product except as explained in your

system documentation. Opening or removing covers that are marked with the triangular symbol with

a lightning bolt may expose you to electrical shock. Components inside these compartments should

be serviced only by an authorized service technician.

•If any of the following conditions occur, unplug the product from the electrical outlet and replace

the part or contact your authorized service provider:

–

The power cable, extension cord, or plug is damaged.

–

An object has fallen into the product.

–

The product has been exposed to water.

–

The product has been dropped or damaged.

–

The product does not operate correctly when you follow the operating instructions.

1-4

User Guide for Cisco Digital Media Player Device Manager 1.0

OL-12472-01

Chapter 1 Introduction

Environmental Tolerances and Safety Guidelines

•Keep your system components away from radiators and heat sources. Also, do not block

cooling vents.

•Do not spill food or liquids on your system components, and never operate the product in a wet

environment.

•Do not push any objects into the openings of your system components. Doing so can cause fire or

electric shock by shorting out interior components.

•Use the product only with other Cisco-approved equipment.

•Allow the product to cool before removing covers or touching internal components.

•Use the correct external power source. Operate the product only from the type of power source

indicated on the electrical ratings label. If you are not sure of the type of power source required,

consult your service representative or local power company.

•Use only approved power cables. If you have not been provided with a power cable for your DMP

or for any AC-powered option intended for your DMP, purchase a power cable that is approved for

use in your country. The power cable must be rated for the product and for the voltage and current

marked on the product's electrical ratings label. The voltage and current rating of the cable should

be greater than the ratings marked on the product.

•To help prevent electric shock, plug the system components and peripheral power cables into

properly grounded electrical outlets. These cables are equipped with three-prong plugs to help

ensure proper grounding. Do not use adapter plugs or remove the grounding prong from a cable. If

you must use an extension cord, use a three-wire cord with properly grounded plugs.

•Observe extension cord and power strip ratings. Make sure that the total ampere rating of all

products plugged into the extension cord or power strip does not exceed 80 percent of the extension

cord or power strip ampere ratings limit.

•Do not use appliance or voltage converters or kits sold for appliances with your product.

•To help protect your system components from sudden, transient increases and decreases in electrical

power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).

•Position cables and power cords carefully; route cables and the power cord and plug so that they

cannot be stepped on or tripped over. Be sure that nothing rests on your system components' cables

or power cord.

•Do not modify power cables or plugs. Consult a licensed electrician or your power company for site

modifications. Always follow your local or national wiring rules.

Protecting Against Electrostatic Discharge

Static electricity can harm delicate components inside a DMP. To prevent static damage, discharge static

electricity from your body before you touch any electronic components. You can do so by touching an

unpainted metal surface on the chassis.

You can also take the following steps to prevent damage from electrostatic discharge (ESD):

•When unpacking a static-sensitive component from its shipping carton, do not remove the

component from the antistatic packing material until you are ready to install the component in your

system. Just before unwrapping the antistatic packaging, be sure to discharge static electricity from

your body.

•When transporting a sensitive component, first place it in an antistatic container or packaging.

•Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads and

workbench pads.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Logiciel

Cisco

Cisco 4700M Manuel utilisateur

Cisco

Cisco Unity Express 8.0 Voice-Mail System Manuel utilisateur

Cisco

Cisco Nexus 7000 Series Mode d’emploi

Cisco

Cisco 4700M Mode d’emploi

Cisco

Cisco 5520 - ASA IPS Edition Bundle Manuel utilisateur

Cisco

Cisco Craft Works Interface Manuel utilisateur

Cisco

Cisco TELEPRESENCE MANAGEMENT SUITE SECURE SERVER - CONFIGURATION GUIDE... Manuel utilisateur

Cisco

Cisco CONFERENCING EXTENSIONS - FOR MICROSOFT EXCHANGE... Manuel utilisateur

Cisco

Cisco ROUTER-SDM-CD Manuel utilisateur

Cisco

Cisco IP Communicator Mode d’emploi

Cisco

Cisco 861W - Integrated Services Router Wireless Manuel utilisateur

Cisco

Cisco TELEPRESENCE CALL DETAIL RECORDS FILE FORMAT... Manuel utilisateur

Cisco

Cisco CVPN3002-8E-K9 - Fast Ethernet VPN Gateway Manuel utilisateur

Cisco

Cisco 6503-E - Catalyst Chassis With Supervisor Engine 32... Mode d’emploi

Cisco

Cisco AP775A - Nexus Converged Network Switch 5010 Manuel de service

Cisco

Cisco CISCO1811 Manuel utilisateur

Cisco

Cisco ASA5500-SC-5= - ASA 5500 Security Context Manuel utilisateur

Cisco

Cisco TELEPRESENCE MANAGEMENT SUITE SECURE SERVER - CONFIGURATION GUIDE... Manuel utilisateur

Cisco

Cisco 2600 Series Comment utiliser

Cisco

Cisco ACTIVE NETWORK ABSTRACTION 3.7.2 Manuel utilisateur

Cisco

Cisco 881 SRST - EN Security Router Manuel utilisateur

Cisco

Cisco III - Supervisor Engine III Manuel utilisateur

Cisco

Cisco OL-11757-01 Mode d’emploi

Cisco

Cisco TMS SERVER REDUNDANCY - CONFIGURATION GUIDE... Manuel utilisateur

Manuels Logiciel populaires d'autres marques

COMPRO

COMPRO COMPROFM Manuel utilisateur

Muratec

Muratec OFFICEBRIDGE ONLINE Manuel utilisateur

Oracle

Oracle Contact Center Anywhere 8.1 Manuel utilisateur

Adobe

Adobe 65007312 - Photoshop Lightroom Manuel

Avaya

Avaya NULL One-X for RIM Blackberry Manuel utilisateur

HP ProLiant BL420c Manuel utilisateur

PS Audio

PS Audio PowerPlay Manuel du propriétaire

Brady

Brady LOCKOUT PRO 3.0 Manuel de service

Avaya

Avaya Interaction Center Manuel utilisateur

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manuel

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manuel utilisateur

Oracle

Oracle Application 9i Manuel utilisateur

Acer

Acer RDM Manuel utilisateur

Canon

Canon Vixia HF21 Manuel utilisateur

Canon

Canon ZR950 Manuel utilisateur

Samsung

Samsung Auto Backup Manuel utilisateur

Polycom

Polycom Vortex EF2201 Instructions d'installation et d'utilisation

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manuel utilisateur