Cisco AS5200 - Universal Access Server Manuel utilisateur
Quick Start Guide
CISCO AS5200 UNIVERSAL ACCESS SERVER
INSTALL AND CONFIGURE
TOOLS AND EQUIPMENT
INSTALL THE UNIVERSAL ACCESS SERVER
CONFIGURE THE UNIVERSAL ACCESS SERVER
1
2
3
1
1Tools and Equipment
Items Included
• Cisco AS5200 universal access server
• 19- and 24-inch rack-mount brackets
• Rubber feet for desktop installation
• Jackscrewsandslide-latchconnectorkitforyour
optional Ethernet transceiver (transceiver not
included)
• RJ-45-to-DB-9 female DTE adapter (labeled
TERMINAL)
• RJ-45-to-DB-25 female DTE adapter (labeled
TERMINAL)
• RJ-45-to-DB-25 male DCE adapter (labeled
MODEM)
• RJ-45-to-RJ-45 rollover console cable
• ESD-preventive wrist strap
• Two nylon cable ties
• Two cable tie holders
• Grounding lug
• Power cord
•Quick Start Guide (this document)
• Cisco AS5200 Universal Access Server
Hardware Installation Guide
• Cisco AS5200 Universal Access Server Software
Configuration Guide
• Regulatory Compliance and Safety Information
document
• Release Notes for the specific Cisco IOS release
installed on the access server
• Documentation CD-ROM
Items Not Included
• Four screws for installing the chassis in a rack
• T1 channel service unit/data service unit
(CSU/DSU) or E1 networks terminating unit
• PC running terminal emulation software for
administrative access
• Modem for remote administrative access
• Ethernet transceiver and a straight-through
RJ-45-to-RJ-45 cable (for connection from the
Ethernet transceiver to an Ethernet hub) OR
Ethernet AUI cable
• Straight-through RJ-48C-to-RJ-48C cable for a
T1 connection
• Serial transition cable
• E1 cable for an E1 connection
• Slot cover for unused slots
• 19-inch telco rack-mount brackets
(P/N 700-01928-01)
Ordering Information
To place an order, contact Cisco Customer Service at
408 526-4000 or 800 553-6387.
2
Prepare the Chassis for
Rack-Mounting
You can install the chassis in a rack or on a desktop.
For a desktop installation, proceed to the next
section, “Prepare the Chassis for Desktop Use.”
Note: Brackets are included. Screws are included
for attaching the brackets to the chassis, but not for
installing the chassis in a rack. You will need four
additional screws to install the chassis in a rack.
Step 1 Attach the brackets using one of the three
methods shown above.
Step 2 Install the chassis in a rack.
H10335
Front panel forward
Rear panel forward
Rear panel forward,
center-mount telco
2Install the Universal Access Server
3
2Install the Universal Access Server (continued)
Prepare the Chassis for
Desktop Use
Attachthe rubberfeet beforeinstalling thechassis on
a desktop.
Note: Rubber feet are included.
Step 1 Locate the rubber feet on the black
adhesive strip that shipped with the
chassis.
Step 2 Place the access server upside-down on a
flat, smooth surface.
Step 3 Peel off the rubber feet from the black
adhesive strip and place them
adhesive-side down on the dotted circles
at each corner of the chassis bottom.
Step 4 Place the access server right-side up on a
flat, smooth, secure surface.
Caution Do not place anything that
weighs more than 10 lb (4.5 kg) on top of
theaccess server. Excessiveweightplaced on
top of the chassis could damage it.
Universal access server
chassis bottom
4
2Install the Universal Access Server (continued)
Connect the Ethernet Port for
10BaseT Ethernet LAN Access
You can connect the access server to a 10BaseT or
thick Ethernet network. For a thick Ethernet
connection, proceed to the next section, “Connect
the Ethernet Port for Thick Ethernet LAN Access.”
You will need an Ethernet transceiver and cable to
connect the access server to a 10BaseT hub.
Note: The cable, transceiver, and hub are not
included.
Step 1 Connect an Ethernet transceiver to the
port labeled AUI on the rear panel of the
access server.
Step 2 Connect an Ethernet cable to the Ethernet
transceiver.
Step 3 Connect the other end of the Ethernet
cable to a 10BaseT hub.
Note: The Ethernet ports on the access server and
the hub must have the same baseband.
H10344
Universal access server
Ethernet AUI port (DB-15)
Ethernet
transceiver
1
10BaseT hub
Straight-through
10BaseT cable
87
5
2Install the Universal Access Server (continued)
Connect the Ethernet Port for
Thick Ethernet LAN Access
You will need an Ethernet AUI cable to connect the
access server to a hub.
Note: The cable and hub are not included.
Step 1 Connect your Ethernet AUI cable to the
port labeled AUI on the rear panel of the
access server.
Step 2 Connect the other end of the Ethernet
cable to an Ethernet hub.
Ethernet hub
H10342
Universal access server
Ethernet AUI port (DB-15)
Ethernet AUI cable
6
2Install the Universal Access Server (continued)
Connect the Dual T1/PRI Card
for WAN Access
You can connect the access server to a dual T1 or
E1/PRI card for WAN access. If you have a dual
E1/PRI card, go to the next section, “Connect the
Dual E1/PRI Card for WAN Access.”
You will need two straight-through
RJ-48C-to-RJ-48C cables to connect the dual
T1/PRI card to a WAN.
Note: RJ-48C-to-RJ-48C cables are not included.
Step 1 Connect one end of the straight-through
RJ-48C-to-RJ-48C cable to the port
labeled Port 0 on the rear panel of the
access server.
Step 2 Connect the other end of the cable to an
RJ-48C jack.
Step 3 Repeats steps 1 and 2 to connect a second
cable to the port labeled Port 1.
RJ-48C jack
Straight-through
RJ-48C-to-RJ-48C cable
T1/PRI
port 0 (RJ-45)
H10337
Universal access server
T1/PRI card T1/PRI
port 1 (RJ-45)
7
2Install the Universal Access Server (continued)
Connect the Dual E1/PRI Card
for WAN Access
You will need two E1 cables to connect the dual
E1/PRI card to a WAN.
Note: E1cablesand E1 networksterminating units
are not included.
Step 1 Connect one end of the E1 cable to the
portlabeled Port0ontherear panelof the
access server.
Step 2 Connect the other end of the cable to an
E1 networks terminating unit.
Step 3 Repeats steps 1 and 2 to connect a second
cable to the port labeled Port 1.
H10338
Universal access server
DB-15, Twinax,
RJ-45, or
BNC connector
E1/PRI card
E1/PRI
port 1 (DB-15)
E1 cable
E1 networks terminating unit
E1/PRI
port 0 (DB-15)
8
2Install the Universal Access Server (continued)
Connect the Synchronous
Serial Port for WAN Access
You will need two CSU/DSUs or modems and two
serial transition cables to connect the synchronous
serial ports to a WAN.
Note: CSU/DSUs and serial transition cables are
not included.
Step 1 Connect one end of a serial transition
cable to the port labeled Serial.
Step 2 Connect the other end of the cable to a
CSU/DSU or other DCE (such as a
modem).
H10339
Universal access server
Synchronous serial
port (DB-60)
EIA/TIA-232, EIA/TIA-449, V.35,
X.21, or EIA-530 connector
Serial
transition
cable
Autres manuels pour AS5200 - Universal Access Server
1
Table des matières
Autres manuels Cisco Serveur
Cisco
Cisco UCS C480 M5 Instructions de montage
Cisco
Cisco expressway ce1100 Manuel utilisateur
Cisco
Cisco SNS-3515 series Manuel
Cisco
Cisco UCS C220 M3 Manuel utilisateur
Cisco
Cisco UCS C240 M3 Guide de démarrage rapide
Cisco
Cisco UCS 5100 Guide de démarrage rapide
Cisco
Cisco C880 M4 Manuel utilisateur
Cisco
Cisco UCS C24 Instructions d'installation et d'entretien
Cisco
Cisco UCS 5100 Guide rapide
Cisco
Cisco SNS-3415 series Manuel de programmation
Cisco
Cisco C880 Series Instructions de montage
Cisco
Cisco UCS Invicta C3124SA Manuel
Cisco
Cisco NAC-3300 Series Manuel utilisateur
Cisco
Cisco TelePresence Server 7010 Manuel utilisateur
Cisco
Cisco UCS C220 M4 Guide de démarrage rapide
Cisco
Cisco TelePresence Manuel utilisateur
Cisco
Cisco UCS B Series Manuel d'installation et d'exploitation
Cisco
Cisco TelePresenceMCU 5300 Series Manuel utilisateur
Cisco
Cisco UCS B440 M2 Manuel utilisateur
Cisco
Cisco Profile Series Manuel utilisateur
