Cisco VEdge 5000 Manuel utilisateur

Release Tab

Click!

Hardware Installation

Package Contents

Four-Post Rack Mount

Secure the router to the rack by inserting

one screw (provided in the accessory box)

into the center holeof each mounting ear.

Tighten the screw ﬁrmly.

Detach both inner rails from the two slide

rails. To do so, slide the inner bracket all

the way to the end of the slide rail.

Then push the slide rail lock outwards

in the direction indicated by the arrow.

Install the two outer rails into the

19-inch rack. To do so, clip the outer rail

ﬁrst to the front and then to the rear

post of the rack. Ensure that you align

the three holes on either side of the

outer rail to the three holes in the

front and rear posts of the rack.

Lift and insert the chassis into the outer

rails, making sure to align it on both sides,

until you hear a click.

Slide the chassis as far back as possible,

pushing the release tabs on both the inner

railsin the direction shown below.

For complete documentation, see

https://sdwan-docs.cisco.com/

Product_Documentation

Router chassis

AC power cords for your

geographical location

RJ-45 to DB-9 console cable

Rack-mounting ears

Slide rails

Mounting screws

Quick Start document

Attach the two inner rails to either side

of the router chassis using the ten inner

rail screws in the accessory box. Attach

the two mounting ears to either side of

the router chassis using the six mounting

ear screws in the accessory box.

Package Contents

Step 1 Step 2

Step 3 Step 4 Step 5 Step 6

Before installing the router or

connecting it to a power source,

read the planning and installation

instructions at:

https://sdwan-docs.cisco.com/

Product_Documentation/vEdge_Routers

Failure to observe these safety warnings

can result in personal injury or death.

Safety Standards

vEdge 5000 Router Quick Start

NOTE: If you power on the router

without inserting a NIM module,

the ZTP process will not work.

Product 78-101267-01, Rev 071118

Insert the NIM modules:

Boot the vEdge router:

Flip the On/Oﬀ switch on the rear

of the router to the ON position.

From vManage > Dashboard or

from vManage > Network > Device

Dashboard, verify that the vEdge

router is operational.

Install at least one NIM module in any

of the four available NIM slots.

Connect AC power to the vEdge router:

Plug one end of the power cord into

the AC power supply.

Plug the other end into the AC

power outlet.

Step 1 Step 2 Step 3 Step 4

Initial Conﬁguration

Caution: If you are connecting AC

power to the router, it is recommended

that the building have an external surge

protective device installed.

From vManage > Conﬁguration >

Devices > WAN Edge List > Upload

WAN Edge List, upload the WAN

Edge authorized serial number ﬁle.

From vManage > Conﬁguration >

Certiﬁcates > WAN Edge List:

a. Check that the router's chassis and

serial number are in the WAN Edge list.

b. Authorize each router by clicking

Valid in the Validate column.

c. Click Send to Controller to send the

WAN Edge list to the controller devices.

From vManage > Conﬁguration >

Templates:

a. Create a device template for the

vEdge router.

b. Attach the router to the device

template.

Conﬁgure the vEdge router:

vEdge 5000 Router Quick Start

Autres manuels Cisco Routeur réseau

Cisco

Cisco AGS+ Mode d’emploi

Cisco

Cisco ASR 901 10G Series Manuel

Cisco

Cisco 7206VXR NPE-400 Manuel utilisateur

Cisco

Cisco 10000 Series Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

Cisco

Cisco 1800 Series Instructions originales

Cisco

Cisco 7120 Series Manuel utilisateur

Cisco

Cisco 3640 Series Manuel utilisateur

Cisco

Cisco WS-C3550-12G Manuel utilisateur

Cisco

Cisco 8200 Series Manuel

Cisco

Cisco 1710 Manuel utilisateur

Cisco

Cisco 1841 - 1841 Integrated Services Router Manuel

Cisco

Cisco ASR 920-24SZ-IM Mode d’emploi

Cisco

Cisco 3800 Series Manuel utilisateur

Cisco

Cisco Small Business SRP520-U Manuel utilisateur

Cisco

Cisco 520-T1 - Small Business Pro SR Secure Router Manuel utilisateur

Cisco

Cisco CGR 1240 Manuel utilisateur

Cisco

Cisco 871 Manuel utilisateur

Cisco

Cisco 220 Series Smart Plus Mode d’emploi

Cisco

Cisco WRT54GP2 Mode d’emploi

Cisco

Cisco 820 Series Manuel utilisateur

Cisco

Cisco 1401 Manuel utilisateur

Cisco

Cisco 809 Guide de démarrage rapide

Cisco

Cisco 867W Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

EnGenius

EnGenius ESR-9710 Manuel utilisateur

LevelOne

LevelOne FBR-1416 Manuel utilisateur

Dynacord

Dynacord Promatrix 6000 Manuel utilisateur

Lorex

Lorex F5D8230-4 Manuel utilisateur

Cisco vEdge 5000 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques