Cisco NCS 4216 Mode d’emploi

Installing the Cisco NCS 4216

This chapter describes how to install the Cisco NCS 4216.

•Prerequisites, on page 1

•Installing the Router in a Rack, on page 1

•Installing the Chassis Ground Connection, on page 17

•Installing the Fan Tray, on page 19

•RSP Installation, on page 26

•Interface Module Installation, on page 29

•Installing the Power Supply, on page 33

•Installing the AC power Supply, on page 39

•Connecting the Cisco NCS 4216 Router to the Network, on page 42

Prerequisites

Before installing the Cisco NCS 4216, it is important to prepare for the installation by:

• Preparing the site (site planning) and reviewing the installation plans or method of procedures (MOP)

• Unpacking and inspecting the Cisco NCS 4216

• Gathering the tools and test equipment required to properly install the Cisco NCS 4216

For more instructions on how to prepare for the installation of the Cisco NCS 4216, see the Preparing for

Installation section.

Installing the Router in a Rack

The sections describe how to install the Cisco NCS 4216 in a rack.

The Cisco NCS 4216 Door is not displayed in the figures below. It is only displayed in the Installing the Cisco

NCS 4216 Door figure.

Note

Installing the Cisco NCS 4216

Installing the Chassis Brackets

The chassis is shipped with mounting brackets that can be installed on the front or rear of the chassis. To

install the brackets on the front of the chassis, perform these steps:

Procedure

Step 1 Remove the rack-mount brackets from the accessory kit and position them beside the router chassis.

Figure 1: Attaching Mounting Brackets for a 23-inch Rack

Step 2 Position one of the brackets against the chassis side, and align the screw holes.

Step 3 Secure the bracket to the chassis with the screws removed when performing Step 1. The recommended

maximum torque is 28 in.-lb (3.16 N-m).

The A907-FAN-E fan tray with filter (A907-FAN-F) cannot be mounted using the mounting screws that are

supported for fan tray. This is not an issue with the FAN tray filter blank panel (A907-FAN-F-B). We

recommend that you use the short screws provided in the following rack mount kits to avoid interference of

the air filter during rack mounting and while replacing the fan tray with the fan tray filter (A907-FAN-E):

• 23" rack mount kit (A907-RCKMT-23IN)

What to do next

Repeat Step 2 and Step 3 for the other bracket.

Installing the Cisco NCS 4216

Installing the Chassis Brackets

Installing Plenum Assembly and Chassis in the Rack

Following steps help you to install the plenum assembly irrespective of the chassis and rack size.

The below illustrations are for representation purpose only. The size displayed in the images may vary

depending upon your chassis type and rack size but the steps remain the same. Ensure to select the 21 or 23

inches adapter for your plenum based on your rack size.

Note

Procedure

Step 1 Position the adapter to the plenum base and secure using a maximum torque of 11.5 in.-lb (1.3 N-m). See

figure below.

Figure 2: Adapter to Plenum

Plenum2Plenum adapter deflector1

-Securing the Plenum to the base3

Step 2 Position the air deflector inside the plenum and secure using a maximum torque of 11.5 in.-lb (1.3 N-m). See

figure below.

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Figure 3: Deflector in Plenum

Plenum2Air deflector1

Step 3 Secure the plenum deflector with a recommended torque of 11.5 in.-lb (1.3 N-m). See figure below.

Figure 4: Plenum Deflector

Securing screws onto plenum2Secure deflector to plenum base1

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Step 4 Position the air baffle and the side plate to the plenum. Secure the air baffle and the side plate using a maximum

torque of 11.5 in.-lb (1.3 N-m). See figure below.

Figure 5: Assembling Air Baffle to the Plenum

Side plate2Air baffle1

Plenum deflector4Plenum base3

Step 5 Secure the air baffle using a maximum torque of 11.5 in.-lb (1.3 N-m). See figure below.

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Figure 6: Securing the Air Baffle Tray

-Securing air baffle to air plenum1

Step 6 Repeat Step-3 to Step-5 to complete the plenum assembly on the other side of the plenum base.

Step 7 Position the front cover hinge assembly on the plenum deflector. Secure the front cover using a recommended

torque of 11.5 in.-lb (1.3 N-m). See figure below.

Figure 7: Front Cover Hinge Assembly on the Plenum

-Front cover hinge assembly1

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Step 8 Secure the cable brackets to the plenum deflector using a torque of 11.5 in.-lb (1.3 N-m). See figure below.

Figure 8: Cable Brackets to Plenum Deflector

Screws to secure brackets2Cable brackets1

Step 9 Position the plenum assembly to the rack and secure the cable brackets to the rack using a torque of 11.5 in.-lb

(1.3 N-m). See figure below.

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Figure 9: Plenum Assembly to Rack

Plenum assembly2Rack1

-Securing the plenum to the brackets3

Step 10 Position cable guides on the router chassis.

Step 11 Guide the router chassis carefully into the plenum assembly. See figure below.

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Figure 10: Chassis Assembly to Plenum in Rack

Cable guides on chassis2Plenum assembly1

-Securing screws to chassis onto rack3

Step 12 Position the door onto the router chassis and slide it into the rack. Secure the screws with a torque of 11.5

in.-lb (1.3 N-m). See figure below.

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Figure 11: Door Assembly to Rack

Door2Chassis in plenum assembly1

-Securing door to the chassis onto rack3

Installing the Air Plenum (A907-F2B-AIR) in the Rack

This procedure installs the air plenum to orient the air flow in front-to- back direction in the NCS 4216 router.

Before performing any of the following procedures, ensure that power is removed from the DC circuit.

Statement 1074

Warning

This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal

use. Statement 39

Warning

For nominal voltage of -60 VDC, the input voltage range is from -40 to -72 VDC.

Note

Installing the Cisco NCS 4216

Installing the Air Plenum (A907-F2B-AIR) in the Rack

Autres manuels pour NCS 4216

Table des matières

Autres manuels Cisco Routeur réseau

Cisco

Cisco Catalyst IR1800 Rugged Series Manuel

Cisco

Cisco HiPort Manuel utilisateur

Cisco

Cisco NCS 540 Series Manuel utilisateur

Cisco

Cisco SB 106 Manuel utilisateur

Cisco

Cisco CPA2501 Manuel utilisateur

Cisco

Cisco ASR 5000 Series Mode d’emploi

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Manuel

Cisco

Cisco Linksys WET610N Manuel utilisateur

Cisco

Cisco Linksys WRT54GS Instructions d'utilisation d'origine

Cisco

Cisco ASR 5500 Mode d’emploi

Cisco

Cisco Network Router Manuel utilisateur

Cisco

Cisco 675E Manuel

Cisco

Cisco ASR 920 series Mode d’emploi

Cisco

Cisco 7513 Series Manuel utilisateur

Cisco

Cisco 676 Instructions d'utilisation et d'entretien

Cisco

Cisco Linksys WRT610N Manuel utilisateur

Cisco

Cisco 6000 series Manuel technique

Cisco

Cisco ASR 5000 Series Mode d’emploi

Cisco

Cisco cBR 8 Manuel utilisateur

Cisco

Cisco 2612 Manuel

Cisco

Cisco IE 2000U Series Instructions d'utilisation et de sécurité

Cisco

Cisco 2811 Series Mode d’emploi

Cisco

Cisco 1760V Manuel utilisateur

Cisco

Cisco 4451 ISR Manuel

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

EnGenius

EnGenius ESR-9710 Manuel utilisateur

LevelOne

LevelOne FBR-1416 Manuel utilisateur

Dynacord

Dynacord Promatrix 6000 Manuel utilisateur

Lorex

Lorex F5D8230-4 Manuel utilisateur