Cisco MERAKI MR57 Manuel utilisateur

MR57 Installation uide

The Cisco Meraki MR57 is a tri-band enterprise-class Wi-Fi 6E cloud-managed access point supporting 2.4 Hz, 5

Hz, and the newly opened unlicensed 6 Hz frequency bands. Designed for the ultra high capacity and highest

density, MR57 meets the needs of the most demanding and mission-critical environments. The access point also

includes a fourth radio dedicated to optimizing the RF environment and securing the airwaves. The MR57 also has an

additional Bluetooth Low Energy (BLE) capable radio used for location and other IoT applications. In addition to this

MR57 has a USB port to support external devices for IoT applications

About this uide

This guide provides instructions on how to install and configure your MR57 access points. This guide also provides

mounting instructions and limited troubleshooting procedures. For more wireless installation guides, refer to the wireless

installation guides section on our documentation website.

Product Overview

Physical Specifications

MR57

Interfaces

• 2x 100/1000/2.5 /5 BASE-T Ethernet (RJ45)

• 1x DC power connector (5.5 mm x 2.5 mm, center positive)

Power

• Power over Ethernet: 42.5 - 57 V (802.3 at/PoE+ and 802.3 bt/

UPoE compliant)

• Alternative 12 V DC input via DC adapter

• Power consumption: 30W to 40W (802.3at required)

• Power over Ethernet injector (MA-INJ-6) and DC adapter (MA-

PWR-50WAC)

Note: PoE Injector and DC adapter sold separately

Note: Actual power consumption may vary depending on the AP

usage.

USB will be disabled when powered by 802/3 at/PoE+

It is recommended that you ensure that LLDP is enabled to allow

proper power negotiation

Environment

• Operating temperature: 32 °F to 104 °F (0 °C to 40 °C)

• Storage and Transportation Temperature: -4 °F to 158 °F (-20

°C to 70 °C)

• Humidity: 5 to 95% non-condensing

Physical Security

• Screws that can be attached to the security hasp of the

universal mounting bracket

• Kensington lock hard point

• Concealed mount plate with anti-tamper cable bay

Product View and Physical Features

Your MR57 has the following features:

A - LED indicator

B - USB Slot

C - Kensington lock hard point

D - Rubber Feet/universal mounting bracket slide in points

E - Cable access bay

The Meraki MR57 comes with the default Cisco universal mounting bracket (AIR-AP-BRACKET-2) that has the following

features:

A - Security Hasp

B - Access Point Mounting Keyholes

C- T-rail attachment points

D - Cable access slot

Security Features

The MR57 features multiple options for physically securing the access point after installation:

1. Security hasp – The universal mounting bracket has a security hasp and can be used to secure the access point to

the universal mounting bracket. Engaging the security screw prevents accidental dislodging and theft.

2. Kensington lock – The access point contains a hard point that allows it to be secured to any nearby permanent

structure using a standard Kensington lock.

Ethernet Ports

The MR57 features two RJ45 Ethernet ports capable of operating at 100/1000/2.5 /5 BASE-T Ethernet (RJ45). The

Ethernet ports can also be combined for link aggregation for an effective data rate of up to 10 bps

The labeled “ETH0, PoE” accepts 802.3 af (in power sharing mode), 802.3at and 802.3bt power. This port is typically

used as the primary uplink to your LAN/WAN.

The labeled “ETH1, PoE” can also accept 802.3 af (in power sharing mode), 802.3at and 802.3bt power. This port is

typically used when the AP needs to support High Availability* in case of primary port failure or Power Sharing* (when

two 802.3af power sources are combined to provide 802.3at power or two 802.3at power sources are combined to

provide 802.3bt power).

Note: High Availability and Power Sharing will be available in future firmware versions

Warning: a single 802.3af power source is not supported

Warning: Some of the pre-standard 802.3at/PoE+ switches do not negotiate full 802.3at power output with the MR57

by default. For these switches (Cisco Catalyst 2960,3560, etc) the switch port that is connected to and powering up the

MR57 should be manually configured to provide 30 watts of power. This can be done by going into the interface of the

switch and setting the inline power to 30 watts using the following command

power inline consumption 30000

before actually powering up the AP. Failure to do so may result in the MR57 not receiving enough power to operate and

can remain in low power which can cause the APs to continuously reboot

Link Aggregation

The two Ethernet ports can be used in a bonded configuration. Ensure that the AP is plugged into 2 switch ports on the

same Ethernet switch that has been configured for LACP bonding. Keep in mind that the maximum bonded aggregate

10 ig wired connection to the switch. See the MR Link Aggregation Configuration uide for more details.

Extending the LAN

Edit

section

If only 1 Ethernet port is used to link the AP to the LAN/WAN, the second Ethernet port may be used to connect devices

that do not have wireless capability. In order to utilize the additional LAN port to extend connectivity, a Port Profile needs

to be applied to AP.

Note: When link aggregation is disabled, Eth0 should be used as the primary uplink and POE port.

Power Source Options

MR57 can be powered by dual M- ig 802.3 bt capable PoE ports. The two Ethernet ports are capable of combining the

power of two 802.3 af/at power to provide 802.3 at/bt. The AP is capable of operating at its full capacity when powered

by a single 802.3bt power at full capacity. All the AP radios will run at full capacity, however, the USB port will be

disabled when powered by a single 802.3 at power.

The table below indicates the different modes of PoE power input and the expected operation of the AP

PoE0 PoE1 2.4GHz 5GHz 6GHz Scan IoT USB

AF None Not Supported and AP does not power up

AF AF 4x4 4x4 4x4 ON ON OFF

AT None 4x4 4x4 4x4 ON ON OFF

AT AT 4x4 4x4 4x4 ON ON ON

BT None 4x4 4x4 4x4 ON ON ON

BT BT 4x4 4x4 4x4 ON ON

MR57 APs can be powered by the PoE power in different modes as mentioned above when using a PoE-

capable switch. MR57 can also be powered by a single 802.3bt capable PoE injector MA-INJ-6 - Meraki multi igabit

802.3bt Power over Ethernet Injector. It can also be powered by an AC power adaptor MA-PWR-50WAC Meraki AC

Adapter for MR Series

Factory Reset Button

If the button is pressed and held for at least ﬁve seconds and then released, the AP will reboot and be restored to its

original factory settings by deleting all configuration information stored on the unit.

LED Indicators and Run Dark Mode

Your access point is equipped with a multi-color LED light on the front of the unit to convey information about system

functionality and performance:

• Orange - AP is booting (permanent Orange suggests hardware issue)

• Rainbow - AP is initializing/scanning

• Blinking Blue - AP is upgrading

• reen - AP in ateway mode with no clients

• Blue - AP in ateway mode with clients

• Blinking Orange - AP can't find uplink

NOTE: Blinking reen LED indicates that the device is in site survey mode. Please see the Conducting Site Surveys

with MR Access Points for more details.

The MR57 access point may be operated in the “Run Dark” mode for additional security and to reduce the visibility of the

access point. In this mode, the LED will not be illuminated. This mode may be enabled through the Meraki Dashboard.

Package Contents

The access point packages contain the following:

MR57 Cloud-Managed Access Point

Cisco Universal Mount Bracket - AIR-AP-BRACKET-2

T-Rail mount attachment (AIR-AP-T-RAIL-R) - and screws (5 Nos - 6-32 x 1/4 included)

X 5

Note: AIR-AP-BRACKET-1 (ordered separately) and AIR-AP-T-RAIL-F (ordered separately) is one other universal

mounting option for MR57 when AP needs to be mounted flush to the wall or ceiling

Safety and Warnings

These operations are to be taken with respect to all local laws. Please take the following into consideration for safe

operation:

• Power off the unit before you begin. Read the installation instructions before connecting the system to the power

source.

• Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with

standard practices for preventing accidents.

• Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to

follow the correct procedures could result in a hazardous situation to people and damage to the system.

• This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective

device is rated not greater than 15 A, 125 Vac, or 10A, 240 Vac.

• Please only power the device with the provided power cables or standard PoE to ensure regulatory compliance.

Pre-install Preparation

You should complete the following steps before going on-site to perform an installation.

Configure your Dashboard Network

The following is a brief overview only of the steps required to add an access point to your network. For detailed

instructions about creating, configuring and managing Meraki wireless networks, refer to the online documentation

(documentation.meraki.com).

1. Login to http://dashboard.meraki.com. If this is your ﬁrst time, create a new account.

2. Find the network to which you plan to add your APs or create a new network.

3. Add your APs to your network. You will need your Meraki order number (found on your invoice) or the serial

number of each AP, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit. You will also need

your license key, which you should have received via email.

4. o to the map / ﬂoor plan view and place each AP on the map by clicking and dragging it to the location where you

plan to mount it.

Warning: If the Networks in the Organization where the MR57 is to be installed have Meraki Sensors, it is required to

create a separate network for the MR57 for staging purposes. Once the MR57 connects to the cloud and updates the

new firmware, then the AP can be moved to the network where the MR57 needs to operate

Check and Set Firmware

To ensure your access point performs optimally immediately following installation, it is recommended that you facilitate a

ﬁrmware upgrade prior to mounting your AP.

1. Attach your AP to power and a wired Internet connection. See the " etting Power to the AP" section for details.

2. The AP will turn on and the LED will glow solid orange. If the unit does not require a ﬁrmware upgrade, the LED

will turn either green (no clients associated) or blue (clients associated) within thirty seconds.

* If the unit requires an upgrade, the LED will begin blinking orange until the upgrade is complete, at which point the LED

will turn solid green or blue. You should allow at least a few minutes for the ﬁrmware upgrade to complete, depending on

the speed of your internet connection.

Table des matières

Autres manuels Cisco Matériel réseau

Cisco

Cisco VIP-4R/4T Instructions d'utilisation et d'entretien

Cisco

Cisco Aironet 1400 Series Manuel utilisateur

Cisco

Cisco IAD1101 Manuel utilisateur

Cisco

Cisco CE-507 - Content Engine 507 Manuel utilisateur

Cisco

Cisco 2650XM Manuel utilisateur

Cisco

Cisco ASA 5506-X Manuel

Cisco

Cisco CTM GateWay Guide d'installation

Cisco

Cisco AIM-VPN - DES/3DES VPN Data Encryption AIM... Manuel utilisateur

Cisco

Cisco SPA901-UK - Small Business Pro Manuel utilisateur

Cisco

Cisco GS7000 Mode d'emploi

Cisco

Cisco NSS4100 - Gigabit Storage System Mode d’emploi

Cisco

Cisco 15530-LCMB-0200 - ESCON Multiplexing Line Card... Manuel

Cisco

Cisco ISA 3000 Guide de démarrage rapide

Cisco

Cisco Cisco ONS 15600 SDH Manuel utilisateur

Cisco

Cisco Gigabit Switch Router Cisco 12012 Manuel utilisateur

Cisco

Cisco VSVM Mode d’emploi

Cisco

Cisco AIR-BR350-A-K9 - Aironet 350 Wireless Bridge Manuel

Cisco

Cisco 1230AG - Aironet - Wireless Access Point Manuel utilisateur

Cisco

Cisco Cisco ASA Series Manuel utilisateur

Cisco

Cisco ISA500 Series Manuel utilisateur

Cisco

Cisco Aironet 340 Series Comment utiliser

Cisco

Cisco NSS4100 - Gigabit Storage System Mode d’emploi

Cisco

Cisco Linksys Business Series Network Storage System... Manuel utilisateur

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur