Christie Solaria One Manuel utilisateur

Retrofitting the Solaria

One with the GDC

SR-1000 IMB

This document describes the steps for installing an integrated media block (IMB) faceplate retrofit kit,

allowing the use of the GDC SR-1000 third party IMB in Solaria One series projectors.

Affected products

These instructions apply to the following products

• Christie Solaria One

• Christie Solaria One+

Prerequisites

The following components are required to complete the installation.

• ASSY SR-1000 IMB (P/N: 003-121741-XX)—GDC-SO-1804-012 SR-1000 Standalone

Integrated Media Block

• Solaria SR-1000 kit (P/N: 003-108430-XX) containing the following components:

• Faceplate (QTY: 1)

• Support Bracket (QTY: 1)

• Backer Bracket (QTY: 1)

• EMI gaskets (QTY: 2)

• Phillips screws 4-40 (QTY: 2)

• Locking nuts 4-40 (QTY:2)

• Void warranty label (QTY: 1)

• Screw M3 Hex (QTY: 3)

• Electrostatic discharge bag (QTY: 1)

Retrofitting the Solaria One with the GDC SR-1000 IMB Instruction Sheet 1

020-102945-03 Rev. 1 (05-2019)

Required tools

The following tools are required to complete the installation.

• Electrostatic discharge mat

• Grounded electrostatic discharge wrist strap

• #1 Phillips screwdriver

• #2 Phillips screwdriver

• 14 mm wrench or 14 mm deep socket

• 3/16 nut driver

• 7/32 nut driver

• 1/4 socket or wrench

• 2.5 mm hex driver

• 2.5 mm ball driver

Upgrading the projector software

Before installing the faceplate kit, upgrade the projector software to Solaria Main Software v4.8.1(3).

1. On the touch panel controller (TPC), tap Menu > Administrator Setup > Upgrade.

2. Tap Upload.

3. Browse to the location of the software upgrade file.

4. Tap the upgrade file and tap Open.

5. In the Available Upgrade Files list, tap the upgrade file loaded in the previous step.

6. Tap Next.

Retrofitting the Solaria One with the GDC SR-1000 IMB

Retrofitting the Solaria One with the GDC SR-1000 IMB Instruction Sheet 2

020-102945-03 Rev. 1 (05-2019)

7. To upgrade all components in the upgrade package, select Upgrade Different Components

Only (Recommended).

8. Tap Next.

Turning off the projector

Before removing the card cage, turn off the projector and disconnect it from AC power.

1. To turn off the lamp, tap and hold the lamp button on the touch panel controller (TPC).

2. To turn off the projector, tap and hold the power button on the TPC.

The projector enters cool down mode.

3. Allow the lamp to cool for a minimum of 10 minutes.

4. Unplug the AC power cable from the projector.

Disassembling the card cage faceplate and

board assembly

Complete the following procedure to remove the faceplate and board assembly from the projector and

take apart the components.

1. Place the electrostatic discharge mat on a clean flat surface.

2. Put on the grounded electrostatic discharge wrist strap.

3. Cut the void warranty label.

4. Using a #2 Phillips® screwdriver, remove the eight screws securing the card cage faceplate to

the card cage. Set the screws aside.

Retrofitting the Solaria One with the GDC SR-1000 IMB

Retrofitting the Solaria One with the GDC SR-1000 IMB Instruction Sheet 3

020-102945-03 Rev. 1 (05-2019)

5. Using the two handles, pull the card cage faceplate assembly out of the card cage.

6. Place the assembly on the electrostatic discharge mat as shown.

7. Using a 14 mm wrench or deep socket, remove the GEN Lock, Sync Out, and LTC Out nuts. Set

the nuts and washers aside.

Retrofitting the Solaria One with the GDC SR-1000 IMB

Retrofitting the Solaria One with the GDC SR-1000 IMB Instruction Sheet 4

020-102945-03 Rev. 1 (05-2019)

8. Using a 3/16 nut driver, remove the two nuts on either side of the AES3 output. Set the nuts

aside.

9. Using a 2.5 mm ball hex driver, remove the left screw securing the Christie IMB to the

faceplate. Set the screw aside.

10. Rotate the assembly 180 degrees.

11. Using a 2.5 mm ball hex driver, remove the right screw securing the Christie IMB to the

faceplate. Set the screw aside.

Retrofitting the Solaria One with the GDC SR-1000 IMB

Retrofitting the Solaria One with the GDC SR-1000 IMB Instruction Sheet 5

020-102945-03 Rev. 1 (05-2019)

12. Using a 2.5 mm hex driver, remove the two screws on the bottom of the PIBS1 board. Set the

screws and support bracket aside.

13. Carefully separate the Christie IMB from the faceplate. Set the Christie IMB aside.

14. Using a 3/16 nut driver, remove the 3D Sync, RS 232 PIBS1, HDMI A/LEFT, and HDMI B/RIGHT

nuts. Set the nuts aside.

Retrofitting the Solaria One with the GDC SR-1000 IMB

Retrofitting the Solaria One with the GDC SR-1000 IMB Instruction Sheet 6

020-102945-03 Rev. 1 (05-2019)

15. Disconnect the harness from the PIB faceplate board.

16. Using a #1 Phillips® screwdriver, remove the two screws securing the PIBS1 board to the

faceplate. Set the screws aside.

17. Carefully separate the PIBS1 board from the faceplate. Set the board aside.

Retrofitting the Solaria One with the GDC SR-1000 IMB

Retrofitting the Solaria One with the GDC SR-1000 IMB Instruction Sheet 7

020-102945-03 Rev. 1 (05-2019)

18. Using a 7/32 nut driver, remove the four nuts securing the PIB faceplate board to the faceplate

and remove the PIB faceplate board and four spacers. Set the nuts, board, and spacers aside.

19. Using a #1 Phillips® screwdriver, remove the four screws securing the handles to the faceplate.

Set the handles and screws aside.

20. Remove the EMI gasket and set it aside.

Installing the faceplate kit

Complete the following procedure to install the GDC SR-1000 IMB to the Solaria One faceplate

provided in the conversion kit.

1. Place the GDC SR-1000 IMB onto the electrostatic discharge mat.

Retrofitting the Solaria One with the GDC SR-1000 IMB

Retrofitting the Solaria One with the GDC SR-1000 IMB Instruction Sheet 8

020-102945-03 Rev. 1 (05-2019)

2. Using a 14mm deep socket or wrench, remove the REF-IN nut and washer (A) and set them

aside.

3. Remove IMB license label plate using two Phillips #1 screws (B) and set it aside.

4. Using a #1 Phillips screwdriver, remove the three 4-40 screws securing the SR-1000 board to

the SR-1000 faceplate (C).

Retrofitting the Solaria One with the GDC SR-1000 IMB

Retrofitting the Solaria One with the GDC SR-1000 IMB Instruction Sheet 9

020-102945-03 Rev. 1 (05-2019)

5. Carefully separate the SR-1000 board from the faceplate.

6. Remove the washer (L) from the SR-1000 REF-IN connector.

Retrofitting the Solaria One with the GDC SR-1000 IMB

Retrofitting the Solaria One with the GDC SR-1000 IMB Instruction Sheet 10

020-102945-03 Rev. 1 (05-2019)

Autres manuels pour Solaria One

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Christie Projecteur

Christie

Christie DHD410S Manuel utilisateur

Christie

Christie LX650 Manuel utilisateur

Christie

Christie LX501 Manuel du propriétaire

Christie

Christie DS+26 Manuel utilisateur

Christie

Christie CineX35 DATZ Manuel utilisateur

Christie

Christie J series 2.0kW Manuel utilisateur

Christie

Christie L2K1500 Manuel utilisateur

Christie

Christie Roadster X9 Manuel utilisateur

Christie

Christie Mirage 2000 Manuel utilisateur

Christie

Christie LW650 Manuel utilisateur

Christie

Christie RPMX-D120U Manuel utilisateur

Christie

Christie DS30 Manuel utilisateur

Christie

Christie LX750 Manuel utilisateur

Christie

Christie LX400 Manuel utilisateur

Christie

Christie Mirage WU-L Manuel utilisateur

Christie

Christie 3308-VIV303-01 Manuel utilisateur

Christie

Christie LX66 Manuel utilisateur

Christie

Christie LW600 Manuel utilisateur

Christie

Christie DS+650 Manuel utilisateur

Christie

Christie D12HD-H Manuel utilisateur

Christie

Christie CP2000-M Manuel utilisateur

Christie

Christie LW40U Manuel utilisateur

Christie

Christie CP4230 Manuel utilisateur

Christie

Christie DWU1075-GS Guide de démarrage rapide

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur