Chesney's Optimyst Manuel utilisateur

Electric Fire Basket &

Electric Stove User Manual

CHESNEY’S

Issue 04

Thank you for choosing this Chesney’s electric ﬁre. Please

read this information guide carefully to be able to safely

install, use and maintain your product.

Front cover upper image shows Chesney’s Electric Fire with Universal Basket and Spherical Fire Dogs.

Lower image shows the Beaumont Electric Stove in yellow paint ﬁnish

CHESNEY’S

Contents

1. Important Safety Advice 2

2. General Information 4

3. Installation Instructions 5

4. Operating the Fire 7

5. Maintenance 10

6. Troubleshooting 20

7. Additional Information 22

8. Warranty Registration 25

1. Important Safety Advice

WHEN USING ELECTRICAL APPLIANCES, BASIC

PRECAUTIONS SHOULD ALWAYS BE FOLLOWEDTO

REDUCETHE RISK OF FIRE, ELECTRICAL SHOCK AND

INJURYTO PERSONS, INCLUDINGTHE FOLLOWING:

1. OVERHEATING

WARNING: IN ORDERTO AVOID OVERHEATING, DO

NOT COVERTHE HEATER. DO NOT PLACE MATERIAL OR

GARMENTS ON, OR OBSTRUCTTHE AIR CIRCULATION

AROUNDTHE APPLIANCE.THE HEATER CARRIES A DO NOT

COVER WARNING.

2. DAMAGE

IFTHE APPLIANCE IS DAMAGED, CHECK WITHTHE

SUPPLIER BEFORE INSTALLATION AND OPERATION.

IFTHE SUPPLY CORD IS DAMAGED IT MUST BE REPLACED

BYTHE MANUFACTURER OR SERVICE AGENT OR A

SIMILARLY QUALIFIED PERSON IN ORDERTO AVOID A

HAZARD.

3. LOCATION

DO NOT USE OUTDOORS.

DO NOT USE INTHE IMMEDIATE SURROUNDINGS OF A

BATH, SHOWER OR SWIMMING POOL.

DO NOT LOCATETHE FIRE IMMEDIATELY BELOW A FIXED

SOCKET OUTLET OR CONNECTION BOX.

ENSURETHAT FURNITURE, CURTAINS OR OTHER

COMBUSTIBLE MATERIAL ARE POSITIONED NO CLOSER

THAN 1 METRE FROMTHE APPLIANCE.

ALTHOUGHTHIS HEATER CONFORMS WITH SAFETY

STANDARDS, WE DO NOT RECOMMEND ITS USE ON DEEP

PILE CARPETS OR ON LONG HAIRTYPE OF RUGS.

4. PLUG POSITIONING

THE APPLIANCE MUST BE POSITIONED SOTHATTHE PLUG

IS ACCESSIBLE.

KEEPTHE SUPPLY CORD AWAY FROMTHE FRONT OFTHE

APPLIANCE.

5. USE OF OTHER CONTROLS

DO NOT USETHIS HEATER IN SERIES WITH ATHERMAL

CONTROL, A PROGRAM CONTROLLER, ATIMER OR

ANY OTHER DEVICETHAT SWITCHES ONTHE HEAT

AUTOMATICALLY, SINCE A FIRE RISK EXISTS WHENTHE

HEATER IS ACCIDENTALLY COVERED OR DISPLACED.

6. UNPLUGGING

INTHE EVENT OF A FAULT UNPLUGTHE DEVICE.

UNPLUGTHE DEVICE WHEN NOT REQUIRED FOR LONG

PERIODS.

7. OWNER/USER

THIS APPLIANCE CAN BE USED BY CHILDREN AGED FORM

8YEARS AND ABOVE AND PERSONS WITH REDUCED

PHYSICAL, SENSORY OR MENTAL CAPABILITIES OR LACK

OF EXPERIENCE AND KNOWLEDGE IFTHEY HAVE BEEN

GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE

OFTHE APPLIANCE IN A SAFE WAY AND UNDERSTANDTHE

HAZARDS INVOLVED. CHILDREN SHALL NOT PLAY WITH

THE APPLIANCE.

CLEANING AND USER MAINTENANCE SHALL NOT BE

MADE BY CHILDREN WITHOUT SUPERVISION.

CHILDREN OF LESSTHAN 3YEARS SHOULD BE KEPT AWAY

UNLESS CONTINUOUSLY SUPERVISED. CHILDREN AGED

FROM 3YEARS AND LESSTHAN 8YEARS SHALL ONLY

SWITCH ON/OFFTHE APPLIANCE PROVIDEDTHAT IT HAS

BEEN PLACED OR INSTALLED IN ITS INTENDED NORMAL

OPERATING POSITION ANDTHEY HAVE BEEN GIVEN

SUPERVISION OR INSTRUCTION CONCERNING USE OF

THE APPLIANCE IN A SAFE WAY AND UNDERSTANDINGTHE

HAZARDS INVOLVED. CHILDREN AGED FROM 3YEARS AND

LESSTHAN 8YEARS SHALL NOT PLUG IN,

REGULATE AND CLEANTHE APPLIANCE OR PERFORM USER

MAINTENANCE.

CAUTION - SOME PARTS OFTHIS PRODUCT CAN BECOME

VERY HOT AND CAUSE BURNS. PARTICULAR ATTENTION

HAS TO BE GIVEN WHERE CHILDREN AND VULNERABLE

PEOPLE ARE PRESENT.

8. ELECTRICITY

WARNING –THIS APPLIANCE MUST BE EARTHED.

THIS APPLIANCE MUST BE USED ON AN AC ~ SUPPLY ONLY

ANDTHE VOLTAGE MARKED ONTHE APPLIANCE MUST

CORRESPONDTOTHE SUPPLY VOLTAGE.

BEFORE SWITCHING ON, PLEASE READTHE SAFETY

ADVICE AND OPERATING INSTRUCTIONS.

2. General Information

Only use ﬁltered water in this appliance.

This model is designed to be free standing and is normally positioned

near a wall, on a non combustible surface.

Always ensure the appliance is sitting on a level, non-combustible

surface.

Please note: Used in an environment where background noise is very

low, it may be possible to hear a sound which is related to the operation

of the ﬂame effect.This is normal and should not be a cause for concern.

If this product experiences a power surge for whatever reason the

product may cut-out.This is a normal safety feature and the product will

resume operation after 30 seconds.

Once installed, never move this appliance or lay on its back, without

draining the water from sump and water tank.

If you intend not using the appliance for longer than 2 weeks, drain the

water from sump and water tank and dry the sump.

The water tank, sump, sump lid, tank cap and air ﬁlters must be cleaned

once every two weeks, particularly in hard water areas.

The appliance should never be operated if the lamps are not working.

The lamps should be regularly inspected as described under

‘Maintenance’ and ‘Changing lamps’.

3. Installation Instructions

This section describes how to set up your ﬁre.

BEFORE YOU START

1. Ensure that all packing items are removed (read any warning labels

carefully) and retain all packing for possible future use e.g. in the event of

moving house or returning the appliance to your supplier.

2. Before connecting to the mains supply, check that the supply voltage is

the same as that stated on the appliance.

INSTALLATION

Electric Fire Baskets: Place the appliance against a wall.

Connect the power cable to the appropriate power connector at the back

of the appliance and plug the power cable into a 13amp/240volt outlet.

Do not yet switch the appliance on.

Electric Stoves: Place the stove in to position allowing a minimum of

125mm all around the stove for ventilation.

Connect the power cable to the appropriate power connector at the back

of the ﬁre and plug the power cable into a 13amp/240volt outlet.

Do not yet switch the appliance on.

Connecting theTransducer Unit + Lamps

1. Release the two red tabs by turning them by 90 degrees (see Fig.1).

2. Lift out the Sump Nozzle (Fig.2).

3. Insert lamps into lamp holders (Fig.3), carefully locating the pins into

the holes (Fig.4).

4. Push lamps ﬁrmly into place.

5. Place theTransducer Unit into the sump and join the cable to the

connector on the sump (Fig 5).

6.To ensure that theTransducer Unit is correctly placed in the sump, the

tab on theTransducer Unit should be lined up with the moulded recess in

the sump (Fig 5a).

7. Ensure that the cable is not placed above the disc on theTransducer

Unit (Fig 5b).To prevent the cable becoming pinched between the nozzle

and the sump, place the cable in the slot in the wall of the sump.

8. Replace the Sump Nozzle and secure it by turning the two red tabs

by 90 degrees (Fig 6).

Filling the WaterTank

9. Place WaterTank in sink and remove cap (turn anti-clockwise to open)

(Fig 7).

10. Fill WaterTank with ﬁltered tap water only.This is necessary to pro-

long the life of the ﬂame and smoke effect producing unit.The water

should be ﬁltered through a conventional domestic water ﬁlter unit and

the ﬁlter should be replaced regularly. Distilled water must not be used.

11. Screw the cap back on – do not overtighten.

12. Place the WaterTank in the Sump, with the tank cap facing down and

the ﬂat side of the tank facing outward (Fig 8).

Assembling the ﬁre

13. Place the Fuelbed on top of the WaterTank.

The appliance is now ready for use.

4. Operating the Fire

This section describes how to activate your ﬁre using either the manual

controls or remote control.

MANUAL CONTROLS

The manual controls are located beneath the hinged ﬂap. (See Fig.9 for

Manual Control lay out).

Switch ‘A’:- Controls the electricity supply to the Fire.

Note:This switch must be in the ‘ON’ ( I ) position for the Fire to operate.

Switch ‘B’:- Press once to turn on the ﬂame effect.This will be

indicated by an audible beep. Although the main lights operate

immediately it will take a further 30 seconds before the ﬂame effect

starts.

(Electric Stove models only)

Press again to give ﬂame effect and half heat.This will be

indicated by two beeps.

Press again to give ﬂame effect and full heat.This will be

indicated by three beeps.

Press again to return to ﬂame effect only.This will be

indicated by one beep.

Press to put ﬁre in to standby mode.This will be indicated by one

beep.

Control Knob ‘C’:- Controls theThermostat setting. (Electric Stove Models only).

Turning the control knob to the left will decrease the temperature setting,

turning the control knob to the right will increase the temperature setting.

Control Knob ‘D’:- Controls the intensity of the ﬂame effect.

Turning the control knob to the left increases the ﬂame effect, turning the

control knob to the right will decrease the ﬂame effect.

SETTING THE THERMOSTAT (Electric Stove models only)

Ensure the ﬁre is plugged in and switch it on to the full heat setting.Turn

the Control Knob ‘C’ fully to the right (max temperature setting) to warm

the room rapidly. When the room temperature has reached the desired

level, turn the thermostat knob back slowly until you hear the thermostat

just click off.The heater will then maintain the room temperature at the

chosen level.

Note: Should your heater fail to come on when the thermostat is at a low

setting, this may be due to the room temperature being higher then the

thermostat setting.

THERMAL SAFETY CUT-OUT (Electric Stove models only)

A thermal safety cut-out is incorporated in the fan heater to prevent

damage due to overheating.This can happen if the heat outlet was

restricted in any way. If the cut-out operates, unplug the heater from the

socket outlet and allow approximately 10 minutes before reconnecting.

Before switching the heater back on remove any obstruction that may be

restricting the heat outlet, then continue normal operation.

Caution: In order to avoid a hazard due to inadvertent resetting of the

thermal cutout, this appliance must not be supplied through an external

switching device, such as a timer, or connected to a switch that is

regularly switched on and off by the utility.

GETTING THE DESIRED FLAME EFFECT

1.The ﬂame control knob ‘D’ (Fig.9) may be turned up or down to give a

more realistic effect.

2. Generally the ﬂames appear more realistic when the ﬂame control is

turned down.

3. Give the ﬂame generator time to react to changes you may make.

4.The appliance will use less water if the ﬂame effect is set to a lower

level (control knob ‘D’).

5. Do not tilt or move the appliance while there is water in the tank or

sump.

6. Make sure that the appliance is on a level ﬂoor.

Autres manuels pour Optimyst

Table des matières

Autres manuels Chesney's Poêle

Chesney's

Chesney's SALISBURY Mode d’emploi

Chesney's

Chesney's 8 Series Mode d'emploi

Chesney's

Chesney's Wood Burning Manuel d'utilisation

Chesney's

Chesney's FIRESIDE Mode d'emploi

Chesney's

Chesney's BEAUMONT Mode d’emploi

Chesney's

Chesney's Beaumont 8SGS Mode d'emploi

Chesney's

Chesney's Optimyst Manuel utilisateur

Chesney's

Chesney's Wood Burning and Multi Fuel Stoves Guide de dépannage

Manuels Poêle populaires d'autres marques

Arada

Arada Cassette Stove Manuel utilisateur

Parmco

Parmco FS 600 Manuel utilisateur

MCZ

MCZ SUITE AIR 10 M2 Manuel utilisateur

HearthStone

HearthStone Stowe DV 8321 Guide de dépannage

Cattara

Cattara FAMILY Manuel utilisateur

Stanley

Stanley Argon F500 OVAL Manuel utilisateur

Avalon

Avalon B-VENT Manuel utilisateur

Nordpeis

Nordpeis Vega Manuel utilisateur

Exquisit

Exquisit EKC601-5 Manuel d'utilisation

Stanley

Stanley Oisin Oil MK II Manuel du propriétaire

Thermocet

Thermocet Brookfield S/CC Manuel utilisateur

HASE

HASE delhi Manuel utilisateur

Vermont Castings

Vermont Castings Intrepid 2 Manuel utilisateur

Italiana Camini

Italiana Camini CLASSICA Guide de démarrage rapide

Avalon

Avalon Vashon Avanti DVS FS Manuel utilisateur

Spartherm

Spartherm ambiente a1 Manuel utilisateur

Dimplex

Dimplex MCFSTV12AU Manuel utilisateur

Warmlite

Warmlite WL46040 Manuel utilisateur