Chamberlain LiftMaster Security+ 327LM Manuel utilisateur

To deactivate any unwanted remote, first erase all codes:

Press and the hold “learn” button on motor unit until the learn indicator light goes out

(approximately 6 seconds). All previous codes are now erased. Reprogram each remote or

keyless entry you wish to use.

Model 372LM Security✚®2-Button Remote Control

The 372LM remote control can activate two separate

315MHz residential or commercial garage door openers

and/or gate openers. The instructions for programming

garage door openers are illustrated below. Please refer to

the original receiver programming for commercial and gate

products.

Both push buttons are factory programmed to work with

315MHz Security✚®receivers having a purple “learn”

button. The rolling code between these buttons and the

receiver changes with each use, randomly accessing over

100 billion new codes.

As an added feature, the push button on the right is

capable of learning or being trained to duplicate or match

another CGI manufactured fixed code or billion-code

remote. This feature is normally used when several

remotes are required to operate one fixed code device

such as a gate opener or commercial dock door. In this

case, the code transmitted to the receiver remains

constant or fixed, not using the Security✚®format.

NOTE: The push button on the left cannot be changed

from Security

✚

®, only the right button is trainable.

KG KG

123

1.Press and release the “learn” button

on the motor unit. The learn

indicator light will glow steadily for

30 seconds.

2. Within 30 seconds, press and hold

the button on the hand-held remote

that you wish to operate your

garage door.

3. Release the button when the motor

unit light blink. It has learned the

code. If light bulbs are not installed,

two clicks will be heard.

KG KG

Instructions are described and illustrated below.

Figure 1

Right

Push Button

(Multi-use)

KG KG

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this

receiver and/or transmitter are prohibited, except for changing the code setting or replacing the

battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

To prevent possible SERIOUS INJURY or DEATH from a moving gate

or garage door:

• ALWAYS keep remote controls out of reach of children. NEVER

permit children to operate, or play with remote control

transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed.

NEVER permit anyone to cross path of moving gate or door.

WARNING

CAUTION

WARNING

ATTENTION

AVERTISSEMENT AVERTISSEMENT

AVERTISSEMENT

To Erase All Codes From Motor Unit Memory

Replacement Parts

3V2032 Lithium battery (2 required) . . . . . . . . . . .10A20

Visor clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29B137

FOR SERVICE DIAL OUR TOLL FREE NUMBER:

US: 1-800-528-2817

CANADA: 1-800-654-4736

1. Begin by having both the 372LM and Remote Control X

available.

2. Press and hold both buttons

on the 372LM until the yellow

indicator light, visible on the

bottom through a small hole,

begins to blink. It will blink for

30 seconds; during this time it

is in the learn or training

mode, and the buttons can be

released.

3. While it is in learn mode, hold

Remote Control X, another

CGI fixed or billion-code

transmitter, back to back with

FCC labels touching as

illustrated.

4. Press and hold the Remote

Control X push button as you

slowly slide the remotes

across each other until the

372LM indicator light blinks

very rapidly, indicating it has

learned the code. (If Remote

Control X is also a 372LM,

you must press and hold its

right push button.)

5. The right button is now

sending the same identical

coded signal as Remote

Control X. This code will

remain inside the 372LM until

replaced with another new

code by repeating steps 1-4 above, or by resetting to

Security✚®.

When Several Remotes operate one device:

To match the 372LM to another 315MHz CGI

manufactured remote’s code (Remote Control X):

FCC Label

Remote Control X

Yellow

Indicator

Light

Resetting the right push button

back to Security✚®as follows.

Push and hold both buttons while

observing the small yellow indicator light.

Hold both buttons for ten seconds until

the yellow indicator light stops blinking.

The remote has defaulted to one of six

randomly preprogrammed Security✚®

settings.

The Remote Control Batteries

The lithium batteries should

produce power for up to 5 years.

To replace, pry open case with

visor clip or screwdriver, as

shown. Insert batteries positive

side up (+).

Dispose of old batteries properly.

Yellow

Indicator

Light

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

WARNING

CAUTION

WARNING

ATTENTION

AVERTISSEMENT AVERTISSEMENT

AVERTISSEMENT

Autres manuels Chamberlain Télécommande

Chamberlain

Chamberlain 892LT Manuel utilisateur

Chamberlain

Chamberlain KLIK3U-BK2 Manuel utilisateur

Chamberlain

Chamberlain Security? 971LM Manuel utilisateur

Chamberlain

Chamberlain 300MC Manuel utilisateur

Chamberlain

Chamberlain KLIK3C-BL Manuel utilisateur

Chamberlain

Chamberlain 312HMC Manuel utilisateur

Chamberlain

Chamberlain LiftMaster 973LM Manuel utilisateur

Chamberlain

Chamberlain LiftMaster 361LM Manuel utilisateur

Chamberlain

Chamberlain SMART GARAGE MYQ-G0301 Manuel utilisateur

Chamberlain

Chamberlain 374UT Manuel utilisateur

Chamberlain

Chamberlain 953EV Manuel utilisateur

Chamberlain

Chamberlain LiftMaster 333LM Manuel utilisateur

Chamberlain

Chamberlain 811LMX Manuel utilisateur

Chamberlain

Chamberlain 375UT Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Security+ 973-315LM Manuel utilisateur

Chamberlain

Chamberlain POWER DRIVE 950CB Manuel utilisateur

Chamberlain

Chamberlain LIFTMASTER 374LM Manuel utilisateur

Chamberlain

Chamberlain 64LM Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional 33LM Manuel utilisateur

Chamberlain

Chamberlain 375LM Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional 98685E Manuel utilisateur

Chamberlain

Chamberlain Passport MAX PPV3M Manuel utilisateur

Chamberlain

Chamberlain POWER DRIVE Whisper DRIVE 953CD Manuel utilisateur

Chamberlain

Chamberlain 54332EML Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation