Central Pneumatic 92917 Manuel d'installation

COIL ROOFING NAILER

3/4” TO 1-3/4” FASTENER LENGTH CAPACITY

92917

93253

SET UP AND OPERATING INSTRUCTIONS

Distributed exclusively by Harbor Freight Tools®.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Cover Revised 08l; Manual Revised 09h

Page 2 For technical questions, please call 1-800-444-3353. SKU 92917

93253

SAVE THIS MANUAL

Keep this manual for the safety

warnings and precautions, assembly,

operating, inspection, maintenance and

cleaning procedures. Write the product’s

serial number in the back of the manual

near the assembly diagram (or month

and year of purchase if product has no

number). Keep this manual and the

receipt in a safe and dry place for future

reference.

Safety Alert Symbol and Signal

Words

In this manual, on the labeling,

and all other information

provided with this product:

This is the safety alert

symbol. It is used to alert

you to potential personal

injury hazards. Obey all

safety messages that

follow this symbol to avoid

possible injury or death.

DANGER indicates

a hazardous

situation which, if not

avoided, will result in death or

serious injury.

WARNING

indicates a

hazardous situation which, if

not avoided, could result in

death or serious injury.

CAUTION, used

with the safety

alert symbol, indicates a

hazardous situation which, if

not avoided, could result in

minor or moderate injury.

NOTICE is used to

address practices

not related to personal injury.

CAUTION, without

the safety alert

symbol, is used to address

practices not related to

personal injury.

Symbol Denitions

Symbol Property or statement

PSI Pounds per square inch of pressure

CFM Cubic Feet per Minute ow

SCFM Cubic Feet per Minute ow at

standard conditions

NPT National pipe thread, tapered

NPS National pipe thread, straight

WARNING marking concerning Risk

of Eye Injury. Wear ANSI-approved

safety goggles with side shields.

Warning marking concerning Risk of

Puncture Injury. Wear heavy-duty

work gloves.

Read the manual before set-up and/

or use.

WARNING marking concerning Risk

of Hearing Loss. Wear hearing

protection.

WARNING marking concerning Risk

of Respiratory Injury. Wear NIOSH-

approved dust mask/respirator.

WARNING marking concerning Risk

of Explosion.

Page 3For technical questions, please call 1-800-444-3353.SKU 92917

93253

IMPORTANT SAFETY

INSTRUCTIONS

INSTRUCTIONS PERTAINING

TO A RISK OF FIRE,

ELECTRIC SHOCK, OR

INJURY TO PERSONS

WARNING – When using tools, basic

precautions should always be

followed, including the following:

General

To reduce the risks of electrica.

shock, re, and injury to persons,

read all the instructions before

using the tool.

Work area

Keep the work area clean and wella. lighted. Cluttered benches and dark

areas increase the risks of electric

shock, re, and injury to persons.

Do not operate the tool inb. explosive atmospheres, such as in

the presence of ammable liquids,

gases, or dust. The tool is able to

create sparks resulting in the ignition

of the dust or fumes.

Keep bystanders, children, andc. visitors away while operating the

tool. Distractions are able to result in

the loss of control of the tool.

Personal safety

Stay alert. Watch what you area. doing and use common sense

when operating the tool. Do not

use the tool while tired or under

the inuence of drugs, alcohol, or

medication. A moment of inattention

while operating the tool increases the

risk of injury to persons.

Dress properly. Do not wear looseb. clothing or jewelry. Contain long

hair. Keep hair, clothing, and

gloves away from moving parts.

Loose clothes, jewelry, or long hair

increases the risk of injury to persons

as a result of being caught in moving

parts.

Avoid unintentional starting. Bec. sure the trigger is released before

connecting to the air supply. Do not

carry the tool with your nger on the

trigger or connect the tool to the air

supply with the trigger pressed.

Do not overreach. Keep properd. footing and balance at all times.

Proper footing and balance

enables better control of the tool in

unexpected situations.

e. Use safety equipment. A

dust mask, non-skid safety

shoes and a hard hat must

be used for the applicable

conditions. Wear heavy-duty work

gloves during use.

f. Always wear eye

protection. Wear ANSI-

approved safety goggles

with side shields.

g. Always wear hearing

protection when using

the tool. Prolonged

exposure to high intensity

noise is able to cause hearing loss.

Do not attach the hose or tool toh. your body. Attach the hose to the

structure to reduce the risk of loss of

balance if the hose shifts.

Page 4 For technical questions, please call 1-800-444-3353. SKU 92917

93253

Always assume that the tooli. contains fasteners. Do not point

the tool toward yourself or anyone

whether it contains fasteners or not.

WARNING – Do not re fastener on j. top of another fastener. This is able

to cause the fastener to be deected

and hit someone, or cause the tool to

react and result in a risk of injury to

persons.

WARNING – Remove nger from k. the trigger when not driving

fasteners. Never carry the tool with

nger on trigger, the tool is able to re

a fastener.

Tool use and care

Use clamps or another practicala. way to secure and support the

workpiece to a stable platform.

Holding the work by hand or against

the body is unstable and can lead to

loss of control.

Do not force the tool.b. Use the

correct tool for the application. The

correct tool will do the job better and

safer at the rate for which the tool is

designed.

Do not use the tool if the triggerc. does not turn the tool on or off.

Any tool that cannot be controlled

with the trigger is dangerous and

must not be used until repaired.

Disconnect the tool from thed. air source before making

adjustments, doing tool

maintenance, clearing jams,

touching the safety nosepiece,

leaving work area, loading,

or unloading the tool. Such

precautionary measures reduce the

risk of injury to persons.

Store the tool when it is idle oute.

of reach of children and other

untrained persons. A tool is

dangerous in the hands of untrained

users.

Maintain the tool with care.f. A

properly maintained tool reduces

the risk of binding and is easier to

control.

Check for misalignment or bindingg. of moving parts, breakage of

parts, and any other condition

that affects the tool’s operation.

If damaged, have the tool serviced

before using. Many accidents are

caused by poorly maintained tools.

There is a risk of bursting if the tool is

damaged.

Use only accessories that areh.

identied by the manufacturer for

the specic tool model. Use of an

accessory not intended for use with

the specic tool model, increases the

risk of injury to persons.

Use only those fasteners listedi.

in the Specications chart of this

manual. Fasteners not identied

for use with this tool by the tool

manufacturer are able to result in

a risk of injury to persons or tool

damage when used in this tool.

Service

Tool service must be performed a.

only by qualied repair personnel.

When servicing a tool, use onlyb. identical replacement parts. Use

only authorized parts.

Page 5For technical questions, please call 1-800-444-3353.SKU 92917

93253

Use only the lubricants suppliedc.

with the tool or specied by the

manufacturer.

Air source

a. Never connect to an air

source that is capable of

exceeding 200 PSI. Over

pressurizing the tool may

cause bursting, abnormal operation,

breakage of the tool or serious injury

to persons. Use only clean, dry,

regulated compressed air at the rated

pressure or within the rated pressure

range as marked on the tool. Always

verify prior to using the tool that the

air source has been adjusted to the

rated air pressure or within the rated

air-pressure range.

Never use oxygen, carbon dioxide,b. combustible gases or any bottled

gas as an air source for the tool.

Such gases are capable of explosion

and serious injury to persons.

SAVE THESE

INSTRUCTIONS.

SPECIFIC SAFETY

INSTRUCTIONS

Operators and others in work area1. MUST wear ANSI-approved safety

goggles with side shields during

use. The employer is responsible to

enforce the use of eye protection by

the operator and others in the work

area.

Keep ngers away from trigger 2. when not driving fasteners to

avoid accidental ring.

Choice of triggering method is3. important. Check manual for

triggering options.

Always assume the tool contains4. fasteners.

Do not point the tool toward yourself5. or anyone whether it contains

fasteners or not.

Do not actuate the tool unless the6.

tool is placed rmly against the

workpiece.

Respect the tool as a working7. implement.

No horseplay. This tool is not a toy8. and can be deadly if misused.

Do not load the tool with fasteners9. when any one of the operating

controls, such as the Trigger or

Safety Nosepiece, is activated.

Do not remove, tamper with, or10. otherwise cause the tool operating

controls to become inoperable.

Do not operate the tool if any portion11. of the tool operating controls is

inoperable, disconnected, altered, or

not working properly.

Disconnect the tool from the air12. supply when:

Unattended.a.

Performing any maintenance orb. repair.

Clearing a jam.c.

Moving the tool to a new location.d.

Do not make any modications to this 13. tool.

Refer to the tool maintenance14. instructions for detailed information

Page 6 For technical questions, please call 1-800-444-3353. SKU 92917

93253

on the proper maintenance of the

tool.

Fire fasteners into an appropriate15. work surface only. Do not attempt to

re fasteners into surfaces too hard

to penetrate. Do not drive fasteners

on top of other fasteners, or at too

steep of an angle. Fasteners can

ricochet causing personal injury.

Do not re fasteners too close to the 16. edge of a workpiece. They may split

the workpiece and y free, causing

personal injury.

Keep clear of the workpiece near the17. area being fastened. Fasteners may

bend sideways during ring, causing

them to exit the workpiece at an

unexpected point, causing personal

injury.

Transport Tool safely. Always18. disconnect air supply when moving

the tool. Carry the tool by the handle

and avoid contact with the trigger.

Hold tool away from head and body.19. During operation the Tool may kick

back causing injury.

Do not re fasteners into a workpiece 20. that has people, utility lines, or other

objects behind or inside it.

Keep balance while using this tool.21. Keep area below clear if working in

an elevated location, and secure air

hose to prevent falls from bystanders

accidentally pulling on it.

Obey the manual for the air22. compressor used to power this tool.

Install an in-line shutoff valve to allow23. immediate control over the air supply

in an emergency, even if a hose is

ruptured.

Do not engrave or stamp anything24. into the housing to prevent

weakening of the housing.

WARNING: Some dust created by25. power sanding, sawing, grinding,

drilling, and other construction

activities, contains chemicals

known [to the State of California] to

cause cancer, birth defects or other

reproductive harm. Some examples

of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and

cement or other masonry products

• Arsenic and chromium from

chemically treated lumber

Your risk from these exposures

varies, depending on how often you

do this type of work. To reduce your

exposure to these chemicals: work in

a well ventilated area, and work with

approved safety equipment, such as

those dust masks that are specially

designed to lter out microscopic

particles. (California Health & Safety

Code § 25249.5, et seq.)

WARNING: The brass components26. of this product contain lead, a

chemical known to the State of

California to cause birth defects (or

other reproductive harm).

(California Health & Safety code §

25249.5, et seq.)

The warnings and precautions27. discussed in this manual cannot

cover all possible conditions and

situations that may occur. It must

be understood by the operator that

common sense and caution are

factors which cannot be built into this

Page 7For technical questions, please call 1-800-444-3353.SKU 92917

93253

product, but must be supplied by the

operator.

Vibration Precautions

This tool vibrates during use.

Repeated or long-term exposure to

vibration may cause temporary or

permanent physical injury, particularly to

the hands, arms and shoulders. To reduce

the risk of vibration-related injury:

Anyone using vibrating tools regularly1. or for an extended period should

rst be examined by a doctor and

then have regular medical check-

ups to ensure medical problems are

not being caused or worsened from

use. Pregnant women or people

who have impaired blood circulation

to the hand, past hand injuries,

nervous system disorders, diabetes,

or Raynaud’s Disease should not use

this tool. If you feel any symptoms

related to vibration (such as tingling,

numbness, and white or blue ngers),

seek medical advice as soon as

possible.

Do not smoke during use. Nicotine2. reduces the blood supply to the

hands and ngers, increasing the risk

of vibration-related injury.

Wear suitable gloves to reduce the3. vibration effects on the user.

Use tools with the lowest vibration4. when there is a choice between

different processes.

Include vibration-free periods each5. day of work.

Grip tool as lightly as possible (while6. still keeping safe control of it). Let

the tool do the work.

To reduce vibration, maintain tool as7. explained in this manual. If abnormal

vibration occurs, stop immediately.

SAVE THESE

INSTRUCTIONS.

Page 8 For technical questions, please call 1-800-444-3353. SKU 92917

93253

Components and Controls

TRIGGER

(73)

CANISTER

SAFETY

NOSEPIECE

AIR

INLET

Safety Nosepiece - Also called the

workpiece contact, the Safety

Nosepiece helps prevent the tool

from ring unless it is pressed against

an object.

INITIAL TOOL SET UP/

ASSEMBLY

Read the ENTIRE IMPORTANT

SAFETY INFORMATION

section at the beginning of this

manual including all text under

subheadings therein before set

up or use of this product.

Note: For additional information regarding

the parts listed in the following pages,

refer to the Assembly Diagram near

the end of this manual.

Unpacking

When unpacking, make sure that the

item is intact and undamaged. If any parts

are missing or broken, please call Harbor

Freight Tools at 1-800-444-3353 as soon

as possible.

This air tool may be shipped with a• protective plug covering the air inlet.

Remove this plug before set up.

REV 05i; 05l; 07j

FUNCTIONAL DESCRIPTION

Specications

92917 93253

Unit Weight 8 lb. 6 lb.

Housing Material Aluminum Alloy Magnesium

Fastener Length Capacity 3/4” to 1-3/4” Long

Fastener Thickness 0.12” Diameter (Approximately)

Canister Capacity 120 Nails

Operating PSI 70 to 100

Air Consumption 4.5 CFM @ 90 PSI

Triggering Type Full-Sequential Safety Mechanism

Accessories 5 mm Hex Wrench,

Pneumatic Tool Oil,

120 Nails, Carrying Case

5 mm Hex Wrench,

Pneumatic Tool Oil

Page 9For technical questions, please call 1-800-444-3353.SKU 92917

93253

Air Supply

TO PREVENT

EXPLOSION:

Use only clean, dry, regulated,

compressed air to power this

tool. Do not use oxygen,

carbon dioxide, combustible

gases, or any other bottled

gas as a power source for this

tool.

Quick

Coupler

Recommended Air Line Components

Regulator with

Pressure Gauge

Quick

Coupler Air Hose

on Reel

Valve FilterOiler

Coupler

Plug

Tool

Air

Compressor

Coupler

Plug

Incorporate a lter, regulator with 1. pressure gauge, oiler, in-line shutoff

valve, and quick coupler for best

service, as shown in the diagram

above. An in-line shutoff ball

valve is an important safety device

because it controls the air supply

even if the air hose is ruptured.

The shutoff valve should be a ball

valve because it can be closed

quickly.

Note: If an automatic oiler system is not

used, add a few drops of Pneumatic

Tool Oil into the airline connection

before operation. Add a few more

drops after each hour of continual

use.

Attach an air hose to the2. compressor’s air outlet. Connect the

air hose to the air inlet of the tool.

Other components, such as a coupler

plug and quick coupler, will make

operation more efcient, but are not

required.

WARNING! TO PREVENT SERIOUS

INJURY FROM ACCIDENTAL

OPERATION:

Do not install a female quick

coupler on the tool. Such a coupler

contains an air valve that will allow

the air tool to retain pressure and

operate accidentally after the air

supply is disconnected.

Note: Air ow, and therefore tool

performance, can be hindered by

undersized air supply components.

The air hose must be long enough3. to reach the work area with enough

extra length to allow free movement

while working.

Release the tool’s trigger.4.

Close the in-line safety valve between5. the compressor and the tool.

Turn on the air compressor according6. to the manufacturer’s directions and

allow it to build up pressure until it

cycles off.

Adjust the air compressor’s output7. regulator so that the air output is

enough to properly power the tool,

but the output will not exceed the

tool’s maximum air pressure at any

time. Adjust the pressure gradually,

while checking the air output gauge

to set the right pressure range.

Page 10 For technical questions, please call 1-800-444-3353. SKU 92917

93253

The air pressure setting must8. not exceed job site regulations/

restrictions. The air pressure setting

must not exceed 90 PSI when being

used with work pieces that have a

thickness of less than 1-3/4”.

Inspect the air connections for leaks.9. Repair any leaks found.

If the tool will not be used at this time,10. turn off and detach the air supply,

safely discharge any residual air

pressure, and release the trigger to

prevent accidental operation.

Note: Residual air pressure should not be

present after the tool is disconnected

from the air supply. However, it is a

good safety measure to attempt to

discharge the tool in a safe fashion

after disconnecting to ensure that the

tool is disconnected and unpowered.

Autres manuels pour 92917

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Central Pneumatic Cloueuse

Central Pneumatic

Central Pneumatic 68057 Manuel utilisateur

Central Pneumatic

Central Pneumatic Contractor 97524 Manuel utilisateur

Central Pneumatic

Central Pneumatic 68021 Manuel d'installation

Central Pneumatic

Central Pneumatic Contractor 97526 Manuel de la liste des pièces

Central Pneumatic

Central Pneumatic Contractor 97526 Manuel utilisateur

Central Pneumatic

Central Pneumatic 47612 Contractor Series Manuel d'installation

Central Pneumatic

Central Pneumatic 68024 Manuel d'installation

Central Pneumatic

Central Pneumatic 95218 Manuel de la liste des pièces

Central Pneumatic

Central Pneumatic 66902 Manuel d'installation

Central Pneumatic

Central Pneumatic 98751 Manuel d'installation

Central Pneumatic

Central Pneumatic 96364 Manuel de la liste des pièces

Central Pneumatic

Central Pneumatic 97525 Manuel utilisateur

Central Pneumatic

Central Pneumatic 93656 Manuel utilisateur

Central Pneumatic

Central Pneumatic 66995 Manuel d'installation

Central Pneumatic

Central Pneumatic 98733 Manuel d'installation

Central Pneumatic

Central Pneumatic 66872 Manuel utilisateur

Central Pneumatic

Central Pneumatic 92917 Manuel utilisateur

Central Pneumatic

Central Pneumatic 69927 Manuel utilisateur

Central Pneumatic

Central Pneumatic 91044 Manuel utilisateur

Central Pneumatic

Central Pneumatic 39092 Manuel utilisateur

Central Pneumatic

Central Pneumatic 93656 Manuel utilisateur

Central Pneumatic

Central Pneumatic 93257 Manuel utilisateur

Central Pneumatic

Central Pneumatic 93680 Manuel utilisateur

Central Pneumatic

Central Pneumatic 41209 Manuel utilisateur

Manuels Cloueuse populaires d'autres marques

Performance Tool

Performance Tool M643 Manuel utilisateur

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Manuel utilisateur

Parkside

Parkside PET 25 B1 Manuel utilisateur

Senco

Senco Fusion Technology F-35XP Manuel utilisateur

Grizzly

Grizzly G1847 Manuel utilisateur

Ryobi

Ryobi R18N18G Manuel utilisateur

Black & Decker

Black & Decker 492848-00 Manuel utilisateur

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Manuel utilisateur

Metabo HPT

Metabo HPT NR 3690DC Mode d’emploi

Surtek

Surtek CN650 Dimensions et guide d'installation

Makita

Makita GF600 Manuel utilisateur

Parkside

Parkside PET 25 B1 Manuel utilisateur

Senco

Senco AirFree 25 Manuel utilisateur

Freeman

Freeman P50LSLW Manuel utilisateur

Aicon PRO

Aicon PRO DAC4507 Manuel utilisateur

DAJ

DAJ XR150A Manuel utilisateur

Makita

Makita AN923 Manuel utilisateur

Grizzly

Grizzly T20644 Manuel utilisateur