Ccei MeteoR2 Manuel

Technical information sheet

MeteoR2

Multifunction swim-

ming pool control box

Réf : PF10Y500 / PF10Y501

Table of Contents

1. Pack contents ......................................................................................................................... 3

2. Technical specifications ......................................................................................................... 3

3. Description ............................................................................................................................. 4

3.1. Presentation of the MeteoR2 ...................................................................................... 4

3.2. Filtering management .................................................................................................. 5

3.3. Auxiliary outputs ........................................................................................................ 7

3.4. Cover closure management ......................................................................................... 7

3.5. Lighting management .................................................................................................. 8

3.6. "Level regulation" Option ......................................................................................... 10

3.7. "Zen'iT" option (remote control) ............................................................................... 10

3.8. "Extra inputs" Option ................................................................................................ 11

3.9. Electric protection - Power supply ............................................................................ 11

4. Installation ........................................................................................................................... 12

4.1. Control box mounting ............................................................................................... 12

4.2. Remote control holder installation ............................................................................. 12

4.3. Temperature sensor ................................................................................................... 12

4.4. Connection to electricity ........................................................................................... 13

5. Operation ............................................................................................................................. 21

5.1. Interface presentation ................................................................................................ 21

5.2. Use ............................................................................................................................ 23

5.3. Radio-frequency remote control - use ....................................................................... 37

5.4. Supervisor menus ...................................................................................................... 39

6. Start up ................................................................................................................................ 44

A. Internal wiring diagram ................................................................................................... 45

B. Menu synopsis .................................................................................................................... 46

C. Declaration of conformity ................................................................................................. 48

Read these instructions carefully before installing, commissioning and using

this product.

MPNT0078 v3.2EN (09/03/2017)

Technical information

sheet MeteoR2 v3.2EN

www.c-

cei.fr 2

Technical information

sheet MeteoR2 v3.2EN

1. Pack contents

• 1 multifunction control box MeteoR2

• 1 temperature sensor with Ø50mm ½" fixing collar

• 1 "BRiO®" 4 way radio-frequency remote control

• 1 bag containing

– 6 screws and 6 wall plugs (power supply box + wall mount for the remote control)

– Wall mount for the remote control unit

• Technical manual (this document)

2. Technical specifications

Power supply voltage SINGLE PHASED 230V~ AC 50/60Hz

Power consumption 20W (control electronics + contactors)

Dimensions: Box: 350 x 290 x 150mm / Box: 395 x 300 x 162mm

Weight

Reference number Control box alone Complete box

PF10Y500 4.5kg 5.4kg

PF10Y501 6.3kg 7.2kg

Installation Wall fasteners (4 screws/wall plugs supplied)

Protection factor IP-44

Floodlight power sup-

ply

PF10Y500 12V 100VA

PF10Y501 12V 300VA

Radio-frequency re-

mote control 4 channels 433.92MHz

Maximum current:

Filter pump 0.3A<In<12.0A

Booster pump (Auxiliary 1) 0.3A<In<12.0A

Filtering + booster pump 1.3A<In<16.0A

Socket (Auxiliary2) 5.0A maximum

Filling solenoid 1.0A maximum

Treatment / Auxiliary (Auxiliary 1) 5.0A maximum

Heating Dry contact (25A max)

Total 16.0A max

www.c-

cei.fr 3

Technical information

sheet MeteoR2 v3.2EN

3. Description

3.1. Presentation of the MeteoR2

The new generation of MeteoR2 control box retains the ease of use and installation of the first

MeteoR while bringing new features designed to allow the end user to control the pool more easily.

Discover how to remotely control the pool, our Bluetooth smartphone app, but also options that can

be used to further centralise controls using a single appliance.

Smart multifunction swimming pool control box

• Filtering

– PROG (Clock), AUTO (operates depending on water temperature)

– Monitoring of the current consumed by the pump.

• Lighting

– Electronic programming clock

– Monochrome

– Colour:

• Toggle switch (micro-power cuts)

• Brio RC®

• Brio RC+®

• Auxiliary 1 with electronic programming clock, a choice of: (Only 1 possible function)

– Auxiliary coupled to the filtering or not

– Booster pump

– Heating

– Treatment (electrolysis control)

• Power socket on the side of the appliance (Auxiliary 2)

– Coupled to the filtering or not

• Level regulation (option)

– KIT-NIV: Floater (pool skimmer) + 230V solenoid (PF10K006 V02)

– KIT-NIV BT: 4 floater channel + 230V solenoid (PF10K009)

www.c-

cei.fr 4

Technical information

sheet MeteoR2 v3.2EN

3.2. Filtering management

It is possible for the MeteoR2 to calculate ideal filtering time every day (AUTO mode) by simply

choosing the start-up time. If you prefer to control the pump operating times, it is also possible (in

PROG mode) to programme 3 fixed filtering time slots (= clock).

3.2.1. Pump current monitoring

The MeteoR2 has a built-in current consumption measurement system for the pump (or pumps if

there is a booster pump). There are several monitoring options available:

• No current monitoring

• Low intensity monitoring ( I < 0.75 In for 2 minutes) only (unpriming, running with no water, etc.)

• Over-intensity monitoring ( I > 1.25 In for 2 minutes) only (shaft jammed, etc.)

• Full monitoring (low and high intensity)

The pump is calibrated automatically and managed by the MeteoR2. In this way, a single control

box model can be used to protect different pump powers without having to change circuit-breaker

calibres. The pump's power consumption must be between 0.3 and 12A.

www.c-

cei.fr 5

Technical information

sheet MeteoR2 v3.2EN

3.2.2. Filtering heat regulation (AUTO mode)

As water temperature varies during the season, filtering times must be adjusted. This daily pump

operation adjustment depending on the temperature is carried out automatically by the MeteoR2

in AUTO filtering mode.

Heat regulated filtering calculation method:

• If the pool temperature is higher than 25°C: daily duration = P1 + d

• If the pool temperature is less than 25°C: daily duration = P1 - d/2

where d = |pool T°C - 25°C| and P1 = daily filtering time for the P1 programme

This calculation method makes it possible to adjust daily filtering times in AUTO mode. If you

think that the daily filtering time is not enough, it can be extended by increasing the time in the P1

programme. Or, if you think that the daily filtering time is too much, it can be reduced by lowering

the time in the P1 programme.

Example of calculated filtering time in AUTO mode;

Pool water

temperature 10°C 15°C 20 25 30 35

Filtering time

in AUTO

mode / P1 = 10h

8h to 18:00

02:30 5h 07:30 10h 15h 20h

Filtering time

in AUTO

mode / P1 = 14h

8h to 22:00

06:30 9h 11:30 14h 19h 24h

Filtering time

in AUTO

mode / P1 = 5h

8h to 13:00

2h 2h (min. du-

ration) 02:30 5h 10h 15h

The start time (pump powered on) can be configured, it is the first P1 programme time. The stop

time will depend on the calculated time and any eventual pump stoppages (not enough water, etc.).

www.c-

cei.fr 6

Technical information

sheet MeteoR2 v3.2EN

3.2.3. Anti-freeze monitoring

The MeteoR2 has a built-in anti-freeze system (can be disabled). It is enabled in AUTO or PROG

mode and its threshold can be configured between +1 and +2°C.

• Below this threshold (If T° < Freezing T°), filtering will be regularly started (10 minutes every

hour) to prevent the water from having time to freeze by making it flow.

• This freeze protection mode stops as soon as the pool temperature exceeds the set threshold (as

soon as T° > freezing T° + 1).

• If the pool temperature drops below 0°C, the pump runs continuously.

Freeze protection monitoring is not active in OFF mode (pump stopped).

3.3. Auxiliary outputs

There are two auxiliary outputs available on the MeteoR2. The first exits to a contactor and is used

to control either:

• Water treatment (in this case the output is coupled to the filter pump)

• Or a booster pump (in this case the output is coupled to the filter pump and the pump current

is monitored)

• Or heating (in this case the output is coupled to the filter pump and depends on a temperature

set point set in the MeteoR2)

• Any auxiliary, whether coupled to the filter pump or not

In all configurations, an electronic clock built into the MeteoR2 is used to programme the operating

times for this auxiliary output.

When the auxiliary is configured for "Treatment", it also possible to have an "Auto" mode: In which

case the daily operating time is calculated automatically by the MeteoR2.

The second auxiliary output is on the electric socket located on the side of the MeteoR2. It can be

coupled to the filter pump or not.

3.4. Cover closure management

The MeteoR2 can be used to connect a dry contact from the automatic cover control box. It is then

informed of the closure of the pool cover. Indeed, daily filtering times (and eventually treatment

times) can be reduced if the pool is protected from UVs, wind, etc. If the cover is closed, the Me-

teoR2 will react as follows:

• If auxiliary 1 is configured for "Water treatment", and the TREATMENT mode is PROG or

AUTO, then the time programmed to activate this output is divided by 4.

• If the filtering is used in AUTO mode, the filtering time is divided by 2.

www.c-

cei.fr 7

Technical information

sheet MeteoR2 v3.2EN

3.5. Lighting management

The MeteoR 2 can be used to control most lighting. Several operating modes are available depend-

ing on whether the pool is fitted with monochrome floodlights (simple ON/OFF) or multicoloured

floodlights (Micro power cuts or compatible with BRiO RC® / BRiO RC+®).

TheBRiORC+®protocolallowsamoreintuitivecontroloftheLEDfloodlightsinstalledinthepool

(direct colour / sequence selection, smartphone control, etc.) and requires the installed floodlights

to be compatible with BRiO RC+®. Check the documentation for your floodlights.

Whatever the type of lighting, the MeteoR 2 also has a built-in electronic clock to manage pool

lighting.

A 4-channel radio-frequency remote control and its wall mount are provided to remotely control

the floodlights. It can be used to control your colour floodlight colours / sequences or the powering

on of your white floodlights.

There is also an automatic (AUTO) mode available to turn on lighting at dusk for a 4 hour period.

(Dusk is only estimated theoretically using the date, it can therefore vary from one day to the next)

www.c-

cei.fr 8

Technical information

sheet MeteoR2 v3.2EN

3.5.1. Compatible floodlights

3.5.1.1. T. Switch mode

Most colour floodlights for pools are compatible with the “Toggle switch” control mode. This con-

sists in creating a short power cut to change colours / programmes.

3.5.1.2. RC mode

All CCEI floodlights are compatible with the RC control mode.

3.5.1.3. RC+ mode

All CCEI floodlights manufactured after February 2016 are compatible with the RC + control mode.

Here is the list:

Floodlight Reference number

BRIO Eolia WEX30 PF10R200 / V05 (and higher)

BRIO Eolia WEX60 PF10R104 / V05 (and higher)

BRIO Eolia WEX100 PF10R005 / V06 (and higher)

BRIO Gaïa GAX30 PK10R102 / V03 (and higher)

Mini BRIO X15 PK10R303 / V02 (and higher)

BRIO ZX30 PK10R007 / V03 (and higher)

BRIO ZX60 PK10R008 / V02 (and higher)

BRIO ZX100 PK10R009 / V02 (and higher)

BRIO Stella WPX30 PF10R410 / V04 (and higher)

www.c-

cei.fr 9

Technical information

sheet MeteoR2 v3.2EN

3.6. "Level regulation" Option

The MeteoR2 includes level regulation. Three kits are available as options to complete your instal-

lation;

• Floater only (no topping up, only low water safety) (ref SF140008).

• NIV KIT (ref PF10K006/V02) for pools fitted with skimmers, it contains

– A floater with a positioning and fixing system,

– A solenoid and a fuse connection kit.

• NIV BT KIT (ref PF10K009) for overflow pools, it contains

– A channel with 4 floaters, a positioning and fixing system,

– A solenoid and a fuse connection kit.

Level regulation can be configured using the following options:

• Low water safety = pump shutdown + topping up (Ref. PF10K006/V02 or SF140008)

• Topping up = topping up only (PF10K006/V02)

• Overflow (regulation for the buffer pool) (PF10K009)

3.7. "Zen'iT" option (remote control)

The Zen'iT control box is the "must have" option

for your MeteoR2. Offset using a cable (maxi-

mum 1000m), it is used to control all your ap-

pliance features. All the menus are identical to

the control box menus. Its "mirror" design and

rounded corners make it possible to install it in

a living area (lounge, pool-house, patio). It must

be installed in a place that is sheltered from rain

and splashing. Up to 3 Zen'iT control boxes can

be installed on a MeteoR2.

3.7.1. IOS / Android application

The Zen'iT control box also has a bluetooth gateway (Bluetooth Low Energy). Using this feature,

you can control all your MeteoR2 functions from your smartphone.

www.c-

cei.fr 10

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ccei Unité de contrôle

ccei

ccei NIVA 3 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur

ccei MeteoR2 Manuel

Manuels Unité de contrôle populaires d'autres marques